March 4, 2013 - Cabarrus County

More documents

Recommendations

Info

Does your bid comply? Yes __X__ No_____ Drip Rails In addition to the drip rail found in the roof extrusion there shall be a drip rail provided over each exterior compartment door. These lower drip rails shall be attached in such a manner to provide quick and easy replacement in the event they are damaged. They shall not be riveted or welded to the doorframe extrusion. Does your bid comply? Yes __X__ No_____ Sub floor Structure The sub floor structure of the modular body shall be constructed of 2" x 2" x .125" structural tubing. There shall be two (2) longitudinal and twelve (12) lateral tubes welded together to form a sub floor structure. The floor structure shall be designed to provide strength while conforming to chassis component clearance requirements and to provide appropriate locations for body mounting devices. Sufficient structure for maximum support and the safe installation of cot mount hardware, or other floor-mounted devices, will be integral to the sub floor structure. The sub floor structure shall include a 4" x 5" x .250" tube of 6061-T6 alloy as an "in-frame" pass through for the OEM fuel filler and DEF filler necks. Routing under the sub-floor frame or frame trimming to accommodate the fuel fill hose is not acceptable to the Purchaser and will not be accepted. Does your bid comply? Yes __X__ No_____ Body Mounting The modular body shall be mounted to the chassis frame at the ten (10) points provided by the OEM chassis manufacturer. For consistency of materials, compliance with the chassis manufacturer’s second unit body mounting requirements and to facilitate future remounting of the body, only OEM supplied mounting hardware shall be used. Methods of body to chassis mounting that do not match the OEM cab mounting process will not be considered due to the stresses created by difference in flexibility between the cab and the modular body. The mounting hardware shall consist of ten (10) 1/2” thick by 6” wide aluminum plates of 6061-T6 alloy welded to the underside of the structural floor to provide puck mounting locations corresponding to the mounting points on the OEM frame rails. The mounting system must be designed so the mounting bolts can be removed during a remount without having to cut the bolts. Drawings shall be furnished to show the mounting system on the unit being bid. 40 Attachment number 1 4-4 Page 74
Does your bid comply? Yes __X__ No_____ Cab-to-body attachment-Type III The body shall be attached to the cab using a minimum of twenty-four (24) .250" x 20 zinc treated steel bolts, fender washers and nylon lock nuts. A one-piece automotive style closed cell bulb seal shall be installed between the cab and body to completely seal the joint between the cab and the modular body. The body shall be primed and painted prior to the cab & chassis being attached to provide maximum protection against electrolysis. The body shall be primed and painted prior to the cab & chassis being attached to provide maximum protection against electrolysis. Does your bid comply? Yes __X__ No_____ Cab-to-body attachment-Type I The cab shall be provided with a steel box frame extended roof covered with 10 ga. steel plate, primed and painted to match the cab roof. The front wall of the module body shall be provided with a bellows mount "walk through" opening to allow walk-thru access from the cab to the module body. This bellows shall be of a rubber type material, heavy duty, with properties allowing it to remain flexible under cold weather conditions, attached securely and sealed in a manner to prevent water, dirt, or air leakage. There shall be, on the inside of the ambulance, an attractive, audio and thermally insulated cover attached to cover the bellows. There shall be provided a door with a fixed Plexiglas window with approximate dimensions of the door being 18" wide x 50" high. Does your bid comply? Yes __X__ No_____ Module Side Entry Door The modular body shall be provided with one (1) entry door on the curbside of the module. A forward hinged single door shall provide an opening of 76 inches high by 32 inches wide, and swing out to 100 degrees for 41 Attachment number 1 4-4 Page 75
Page 1 and 2:
CABARRUS COUNTY BOARD OF COMMISSION
Page 3 and 4:
ATTACHMENTS QSCB Project Status Rep
Page 5 and 6:
School Project Description Total Or
Page 7 and 8:
Page 9 and 10:
Cabarrus County Facility Data 11 Ad
Page 11 and 12:
Weaknesses of Facilities in Cabarru
Page 13 and 14:
Page 15 and 16:
No COUNTY MANAGER’S RECOMMENDATIO
Page 17 and 18:
FRIDAY, JANUARY 18, 2013, 3:00 PM S
Page 19 and 20:
Page 21 and 22:
Cabarrus County Budget Amendment Re
Page 23 and 24: North Carolina Department of Transp
Page 25 and 26: Based on the Revised Summary Sheet
Page 27 and 28: CABARRUS COUNTY BOARD OF COMMISSION
Page 29 and 30: Cabarrus County Budget Amendment Re
Page 31 and 32: Section II. A. Special appropriatio
Page 35 and 36: Specifications for a Type 1 (conven
Page 37 and 38: When submitting their Bid Proposal,
Page 39 and 40: Scope This specification covers a n
Page 41 and 42: Does your bid comply? Yes __X__ No_
Page 43 and 44: All bid prices and conditions must
Page 45 and 46: The term "heavy-duty" as used to de
Page 47 and 48: Front Suspension - front independen
Page 49 and 50: Trailer tow hooks - front (2) Wheel
Page 51 and 52: ventilated with clean air. The syst
Page 53 and 54: Engine High-Idle Speed Control, Aut
Page 57 and 58: Mud Flaps In order to provide addit
Page 59 and 60: Driver's Compartment Controls The F
Page 63 and 64: Circuit Connections Circuit connect
Page 67 and 68: control console and will be an inte
Page 69 and 70: Each compartment and module entry d
Page 71 and 72: There shall be provided a clear LED
Page 73: The vertical corner posts and the r
Page 77 and 78: Side Window There shall be a fixed
Page 79 and 80: (Q). Each compartment door shall ha
Page 81 and 82: Dimensions given here are applicabl
Page 83 and 84: Floor The sub floor of module body
Page 85 and 86: Patient Compartment Carbon Monoxide
Page 87 and 88: eak angles and locations to be pre-
Page 89 and 90: Cabinet Layout See drawings accompa
Page 91 and 92: controlled by a low voltage switch
Page 93 and 94: Two (2) 100-watt Cast SA4319 speake
Page 95 and 96: of F3963 and F3964 etch primer. The
Page 99 and 100: EXTRACT FROM MINUTES OF PUBLIC HEAR
Page 101 and 102: EXTRACT FROM MINUTES OF MEETING BOA
Page 103 and 104: the aggregate principal amount of t
Page 105 and 106: date for such interest, pursuant to
Page 107 and 108: Section 6. following form: The Bond
Page 109 and 110: of any Bond to be redeemed shall be
Page 111 and 112: [The following four paragraphs are
Page 113 and 114: The Bond Registrar shall not be req
Page 115 and 116: ASSIGNMENT FOR VALUE RECEIVED the u
Page 117 and 118: thereof shall also set forth, if le
Page 119 and 120: time Bonds in accordance with the p
Page 121 and 122: the best interests of the County in
Page 123 and 124: (d) (6) adverse tax opinions, the i
Page 125 and 126:
proceeds of the Bonds, and to perfo
Page 127 and 128:
BUDGET AMENDMENT REQUIRED: Yes COUN
Page 129 and 130:
Totalnumberofinspections July Augus
Page 131 and 132:
REVISED Buildings %Change HousingUn
Page 133 and 134:
SUBMITTED BY: Mark Browder, Mark II
Page 135 and 136:
2012 - 2013 Renewal Estimate Mark I
Page 137 and 138:
2012 - 2013 Experience Mark III Emp
Page 139 and 140:
2013 - 2014 Renewal Options Mark II
Page 141 and 142:
Employee Health Improvement Initiat
Page 143 and 144:
In the spring of 2013: Employee Hea
Page 145 and 146:
Employee Health Improvement Initiat
Page 147 and 148:
Page 149 and 150:
COORDINATOR AT 704-920-2100 AT LEAS
show all

March 4, 2013 - Cabarrus County

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?