March 4, 2013 - Cabarrus County

More documents

Recommendations

Info

Does your bid comply? Yes __X__ No_____ Body Skin Thickness and Alloy All sidewall, front and rear panels will be single piece .125” 5052-H32 aluminum with a minimum density of 1.75 pounds per square foot. The single piece body skin shall be attached to the 2” x 2” structural with interval welds spaced at 10”-12” along the mating edge of each structural tubing member. In addition, the skin shall be bonded to each structural upright full length using high strength Chemrex CX400QT structural adhesive. The body side skin is welded to each corner post along the inside contact point of each corner extrusion. This method of installation provides a welded application to the entire perimeter of the body side skin, a bonded attachment to the wall substructure and an additional flexible adhesive bond for enhanced support. Alternative bonding methods that utilize liquids, caulks, tape or rivets as an attachment process for bonding the side skin to the body structure will not be acceptable. Does your bid comply? Yes __X__ No_____ Body Structural Framing All framing will be a minimum of 2" x 2" square tubing with a wall thickness of .125” and an alloy rating of 6061-T6. Tubing members will be spaced on a maximum of 12-inch centers for optimum load and structural support. Gussets shall be added at all stress points. Gussets will be either .250” plate or 2" square tubing welded to the adjacent structural members at 45-degree angles for diagonal strength. Does your bid comply? Yes __X__ No_____ Vertical Corner Posts As a part of the inherent structural strength of the modular unit, the use of reinforced extruded corner post is required. The vertical posts will have a minimum wall thickness of .125" and will have an alloy rating of 5052- H32. The extrusion shall have full-length slots for insertion of the exterior wall skin. This characteristic eliminates exposed panel edges and with the added benefit of seam sealed joints, reduces oxidation and corrosion. The slot provides an area on the inside of the extrusion/sheet junction for welding the body side skin to the corner extrusion. Additionally, the extrusion shall incorporate a full-length, integrally extruded center reinforcement rib with a minimum thickness of .200 inches and two side flanges. Bidder must be prepared to verify compliance with this section. Drawings and samples of actual materials used may be required. The lower ends of the vertical corner posts must be closed off with an aluminum plate. 38 Attachment number 1 4-4 Page 72
The vertical corner posts and the roof corner extrusion shall be mated by a cast aluminum corner cap welded to all three extrusions inside and out. Construction which merely welds the extrusions together is unacceptable. Does your bid comply? Yes __X__ No_____ Roof The roof skin shall consist of a single sheet of .090”– 5052-H32 alloy rated aluminum. Roof framing shall be 4” x 4” tubing with a wall thickness of .125” and an alloy rating of 6061-T6. These beams shall be formed with an arch to give the roof a minimum of ¾” crown at the center, to prevent pooling of snow/ice/water. They shall also be engineered and designed with openings for the center wiring harness and, if equipped, for ducting for overhead HVAC system. These structural tubing members shall be set on 16 inch centers. The roof sheeting shall not be required as integral part of the roof structure; however, the roof skin shall be welded to the outer extrusions using a full perimeter, continuous weld on all four sides. The roof structure itself shall be designed to enhance the safety and structural integrity of the modular body and to meet or exceed the load requirements of AMD Standard No. 001. A flat roof will not be considered. Does your bid comply? Yes __X__ No_____ Horizontal Roof Edge The extruded roof edge structural members will measure 6" x 4.75" with a 2" radius, a minimum wall thickness of .125" and an alloy rating of 5052-H32. The roof extrusions will include an integral, full-length drip rail for each side and from side to side on both the front and rear of the module. Drip rails which are attached to the roof edge perimeter may not be attached using screws, adhesives, or rivets. Does your bid comply? Yes __X__ No_____ Static Load Test The ambulance body as a unit shall be designed and built to provide impact resistance. The body shall be of sufficient strength to support a minimum of( 2.5) times the weight of the "fully" loaded vehicle on its top and side, without crushing, separation of joint or excessive deformation of roof bows, reinforcements, body parts, doors, floor members, inner linings, outer panels, rub rails or any other structure in accordance with AMD Standard No. 001. 39 Attachment number 1 4-4 Page 73
Page 1 and 2:
CABARRUS COUNTY BOARD OF COMMISSION
Page 3 and 4:
ATTACHMENTS QSCB Project Status Rep
Page 5 and 6:
School Project Description Total Or
Page 7 and 8:
Page 9 and 10:
Cabarrus County Facility Data 11 Ad
Page 11 and 12:
Weaknesses of Facilities in Cabarru
Page 13 and 14:
Page 15 and 16:
No COUNTY MANAGER’S RECOMMENDATIO
Page 17 and 18:
FRIDAY, JANUARY 18, 2013, 3:00 PM S
Page 19 and 20:
Page 21 and 22: Cabarrus County Budget Amendment Re
Page 23 and 24: North Carolina Department of Transp
Page 25 and 26: Based on the Revised Summary Sheet
Page 27 and 28: CABARRUS COUNTY BOARD OF COMMISSION
Page 29 and 30: Cabarrus County Budget Amendment Re
Page 31 and 32: Section II. A. Special appropriatio
Page 35 and 36: Specifications for a Type 1 (conven
Page 37 and 38: When submitting their Bid Proposal,
Page 39 and 40: Scope This specification covers a n
Page 41 and 42: Does your bid comply? Yes __X__ No_
Page 43 and 44: All bid prices and conditions must
Page 45 and 46: The term "heavy-duty" as used to de
Page 47 and 48: Front Suspension - front independen
Page 49 and 50: Trailer tow hooks - front (2) Wheel
Page 51 and 52: ventilated with clean air. The syst
Page 53 and 54: Engine High-Idle Speed Control, Aut
Page 57 and 58: Mud Flaps In order to provide addit
Page 59 and 60: Driver's Compartment Controls The F
Page 63 and 64: Circuit Connections Circuit connect
Page 67 and 68: control console and will be an inte
Page 69 and 70: Each compartment and module entry d
Page 71: There shall be provided a clear LED
Page 77 and 78: Side Window There shall be a fixed
Page 79 and 80: (Q). Each compartment door shall ha
Page 81 and 82: Dimensions given here are applicabl
Page 83 and 84: Floor The sub floor of module body
Page 85 and 86: Patient Compartment Carbon Monoxide
Page 87 and 88: eak angles and locations to be pre-
Page 89 and 90: Cabinet Layout See drawings accompa
Page 91 and 92: controlled by a low voltage switch
Page 93 and 94: Two (2) 100-watt Cast SA4319 speake
Page 95 and 96: of F3963 and F3964 etch primer. The
Page 99 and 100: EXTRACT FROM MINUTES OF PUBLIC HEAR
Page 101 and 102: EXTRACT FROM MINUTES OF MEETING BOA
Page 103 and 104: the aggregate principal amount of t
Page 105 and 106: date for such interest, pursuant to
Page 107 and 108: Section 6. following form: The Bond
Page 109 and 110: of any Bond to be redeemed shall be
Page 111 and 112: [The following four paragraphs are
Page 113 and 114: The Bond Registrar shall not be req
Page 115 and 116: ASSIGNMENT FOR VALUE RECEIVED the u
Page 117 and 118: thereof shall also set forth, if le
Page 119 and 120: time Bonds in accordance with the p
Page 121 and 122: the best interests of the County in
Page 123 and 124:
(d) (6) adverse tax opinions, the i
Page 125 and 126:
proceeds of the Bonds, and to perfo
Page 127 and 128:
BUDGET AMENDMENT REQUIRED: Yes COUN
Page 129 and 130:
Totalnumberofinspections July Augus
Page 131 and 132:
REVISED Buildings %Change HousingUn
Page 133 and 134:
SUBMITTED BY: Mark Browder, Mark II
Page 135 and 136:
2012 - 2013 Renewal Estimate Mark I
Page 137 and 138:
2012 - 2013 Experience Mark III Emp
Page 139 and 140:
2013 - 2014 Renewal Options Mark II
Page 141 and 142:
Employee Health Improvement Initiat
Page 143 and 144:
In the spring of 2013: Employee Hea
Page 145 and 146:
Employee Health Improvement Initiat
Page 147 and 148:
Page 149 and 150:
COORDINATOR AT 704-920-2100 AT LEAS
show all

March 4, 2013 - Cabarrus County

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?