E.g. Wheels, Bearings, Hubs, Drive Shafts, Etc.
E.g. Wheels, Bearings, Hubs, Drive Shafts, Etc. E.g. Wheels, Bearings, Hubs, Drive Shafts, Etc.
Wheel Hubs KL-0174 Puller Series Puller Bolts Puller plates Nut The KL-0174 Puller Series used together with the hydraulic cylinder KL-0215-10 (17t.) or with the hydraulic spindle KL-0045-7 (12t.) allow to press out drive shafts glued with loctite or rusted. Together with the slide hammer KL-0049-31 wheel hubs, brake drums and half shafts can be removed directly in-situ on the vehicle. Thanks to the use and combination of different perforated disks, tie bolts and drives the Puller Series KL-0174 is almost universally applicable. Adaptor Spindle Application: Slide Hammer Drive shaft pressing out: mechanical or hydraulic drive e.g. the use of the 17 t. hydraulic cylinder KL-0040-2500 and of the press spindle KL-0039-1930) allows you to press out even rusted, very stuck or glued drive shafts. Wheel Hubs Wheel hubs, half shafts and brake drums removal: with slide hammer KL-0049-31 By using the slide hammer KL-0049-31 wheel hubs, brake drums and half shafts can be removed directly in-situ on the vehicle. Standard Hub, 4 Wheel Bolts Standard Hub, 5 Wheel nuts 4X4 Off-Road, 6 Wheel nuts In order to select the correct puller, the following important data must be known: PCD and number of studs (3, 4, 5 or 6). important to determine the correct plate size with the correct hole pattern Position of wheel bolts number of pitches (here 4) Thread diameter of wheel bolts or nuts Pitch Circle Diameter (PCD) Wheel Hub Wheel nuts (type M) or Screws (type B) and thread diameters. important to determine the puller bolts with inner or outer threads. What drive method is to be used, mechanical spindle, slide-hammer, Hydraulic spindle or Hydraulic Cylinder? important to determine the appropriate adaptor. (see table) 3.3-1 (98) Copyright KLANN-Spezial-Werkzeugbau-GmbH, Germany - 6.E1
Axle repairs e.g. Wheels, Bearings, Hubs, Drive Shafts, etc. Wheel Hubs KL-0174 Puller Series Components for the assembly of a Puller from the Puller-Series KL-0174-... The puller plates with the sizes 0, 1, 2 and 3 can be assembled to an all-purpose puller-system by using different adaptors, spindles, puller bolts, screws and drives. 1. Assembling and mounting the puller: 2. Pressing out the drive shaft: 3. Extracting the wheel hub: Examples of application: Removing the hub using a slide-hammer Pressing out the drive-shaft ange Pressing out the drive-shaft using 17 ton Hydraulic Cylinder. Pressing out the drive-shaft with the mechanical spindle. KL-0174-559 KL-0174-559 KL-0040-2500 Copyright KLANN-Spezial-Werkzeugbau-GmbH, Germany - 6.E1 (99) 3.3-2
- Page 1 and 2: Axle repairs e.g. Wheels, Bearings,
- Page 3 and 4: Axle repairs e.g. Wheels, Bearings,
- Page 5 and 6: Axle repairs e.g. Wheels, Bearings,
- Page 7 and 8: Axle repairs e.g. Wheels, Bearings,
- Page 9 and 10: Axle repairs e.g. Wheels, Bearings,
- Page 11 and 12: Axle repairs e.g. Wheels, Bearings,
- Page 13 and 14: Axle repairs e.g. Wheels, Bearings,
- Page 15 and 16: Axle repairs e.g. Wheels, Bearings,
- Page 17 and 18: Axle repairs e.g. Wheels, Bearings,
- Page 19 and 20: Axle repairs e.g. Wheels, Bearings,
- Page 21 and 22: Axle repairs e.g. Wheels, Bearings,
- Page 23 and 24: Axle repairs e.g. Wheels, Bearings,
- Page 25: Axle repairs e.g. Wheels, Bearings,
- Page 29 and 30: Axle repairs e.g. Wheels, Bearings,
- Page 31 and 32: Axle repairs e.g. Wheels, Bearings,
- Page 33 and 34: Axle repairs e.g. Wheels, Bearings,
- Page 35 and 36: Axle repairs e.g. Wheels, Bearings,
- Page 37 and 38: Axle repairs e.g. Wheels, Bearings,
- Page 39 and 40: Axle repairs e.g. Wheels, Bearings,
- Page 41 and 42: Axle repairs e.g. Wheels, Bearings,
- Page 43 and 44: Axle repairs e.g. Wheels, Bearings,
- Page 45 and 46: Axle repairs e.g. Wheels, Bearings,
- Page 47 and 48: Axle repairs e.g. Wheels, Bearings,
- Page 49 and 50: Axle repairs e.g. Wheels, Bearings,
Wheel <strong>Hubs</strong><br />
KL-0174 Puller Series<br />
Puller Bolts<br />
Puller plates<br />
Nut<br />
The KL-0174 Puller Series used together with the hydraulic cylinder<br />
KL-0215-10 (17t.) or with the hydraulic spindle KL-0045-7 (12t.) allow to<br />
press out drive shafts glued with loctite or rusted. Together with the slide<br />
hammer KL-0049-31 wheel hubs, brake drums and half shafts can be<br />
removed directly in-situ on the vehicle.<br />
Thanks to the use and combination of different perforated disks, tie bolts<br />
and drives the Puller Series KL-0174 is almost universally applicable.<br />
Adaptor<br />
Spindle<br />
Application:<br />
Slide Hammer<br />
<strong>Drive</strong> shaft pressing out:<br />
mechanical or hydraulic drive<br />
e.g. the use of the 17 t. hydraulic cylinder KL-0040-2500 and of the<br />
press spindle KL-0039-1930) allows you to press out even rusted,<br />
very stuck or glued drive shafts.<br />
Wheel <strong>Hubs</strong><br />
Wheel hubs, half shafts and brake drums removal:<br />
with slide hammer KL-0049-31<br />
By using the slide hammer KL-0049-31 wheel hubs, brake drums and<br />
half shafts can be removed directly in-situ on the vehicle.<br />
Standard Hub,<br />
4 Wheel Bolts<br />
Standard Hub,<br />
5 Wheel nuts<br />
4X4 Off-Road,<br />
6 Wheel nuts<br />
In order to select the correct puller, the following important data<br />
must be known:<br />
PCD and number of studs (3, 4, 5 or 6).<br />
important to determine the correct plate size with the correct<br />
hole pattern<br />
Position of wheel bolts<br />
number of pitches (here 4)<br />
Thread diameter<br />
of wheel<br />
bolts or nuts<br />
Pitch Circle Diameter<br />
(PCD)<br />
Wheel Hub<br />
Wheel nuts (type M) or Screws (type B) and thread diameters.<br />
important to determine the puller bolts with inner or outer threads.<br />
What drive method is to be used, mechanical spindle, slide-hammer,<br />
Hydraulic spindle or Hydraulic Cylinder?<br />
important to determine the appropriate adaptor. (see table)<br />
3.3-1<br />
(98) Copyright KLANN-Spezial-Werkzeugbau-GmbH, Germany - 6.E1