04.11.2012 Views

Unichiller in Desktop Housing - HUBER

Unichiller in Desktop Housing - HUBER

Unichiller in Desktop Housing - HUBER

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

Start up<br />

General<br />

All models must be moved and <strong>in</strong>stalled <strong>in</strong> an upright position. Provide for a stable<br />

<strong>in</strong>stallation and make sure that the thermostat cannot tilt. Ensure that sufficient fresh<br />

air is available for the circulation pump and compressors at the <strong>in</strong>stallation site. The<br />

warm exhaust air must be able to escape unh<strong>in</strong>dered upwards.<br />

Water-cool<strong>in</strong>g (valid for units with water cool<strong>in</strong>g)<br />

A cool<strong>in</strong>g water controller is used <strong>in</strong> Huber temper<strong>in</strong>g devices with water cool<strong>in</strong>g, <strong>in</strong><br />

order to reduce the cool<strong>in</strong>g water consumption. This only allows as much cool<strong>in</strong>g water<br />

to flow as is required by the current load situation of the temper<strong>in</strong>g device. Only little<br />

cool<strong>in</strong>g water is consumed, if the required refrigerat<strong>in</strong>g capacity is low. No cool<strong>in</strong>g<br />

water flows <strong>in</strong> the OFF state. Only use pressure-resistant hoses <strong>in</strong> the cool<strong>in</strong>g water<br />

circuit.<br />

Connection diagram:<br />

water <strong>in</strong>let water outlet dra<strong>in</strong><strong>in</strong>g / water<br />

Caution!<br />

Depend<strong>in</strong>g upon mode of operation and available cool<strong>in</strong>g water pressure, a cool<strong>in</strong>g<br />

water pressure of > 2 bar can build up <strong>in</strong> the cool<strong>in</strong>g water supply l<strong>in</strong>e. In order to<br />

avoid flood<strong>in</strong>g of the premises, check the leak tightness and quality of the hoses, hose<br />

connections <strong>in</strong> regular <strong>in</strong>tervals, and if necessary take appropriate measures<br />

(Replacement). Close down the cool<strong>in</strong>g water supply to the temper<strong>in</strong>g device even<br />

dur<strong>in</strong>g shorter shutdowns (e.g. over night).<br />

Re<strong>in</strong>forced hoses must be used for <strong>in</strong>creased safety requirements.<br />

Preparation of devices with water-cool<strong>in</strong>g:<br />

Establish the hose connections for the cool<strong>in</strong>g water. The filter screen has to be<br />

<strong>in</strong>serted <strong>in</strong>to the cool<strong>in</strong>g water <strong>in</strong>let. Please <strong>in</strong>fer the position of the cool<strong>in</strong>g water<br />

connections from the connection diagram <strong>in</strong> the appendix. Cool<strong>in</strong>g water connectors<br />

Dra<strong>in</strong>age with seal cap held closed and /or close. Open all stop valves. Please <strong>in</strong>fer the<br />

m<strong>in</strong>imum / maximum differential pressure <strong>in</strong> the cool<strong>in</strong>g water circuit and the<br />

recommended cool<strong>in</strong>g water <strong>in</strong>let temperature from the data sheet.<br />

Information on water quality can be found on our website (www.huber-onl<strong>in</strong>e.com)<br />

under "Download / Safety data sheets thermofluids / Characteristics of water".<br />

19

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!