Renold Clutches & Couplings - casa sueca s.a.

More documents

Recommendations

Info

PM Design Variations The PM coupling range can be adapted to meet customer needs. Below are some of the arrangements that have been produced. For a more comprehensive list contact Renold Hi-Tec Couplings. Cardan shaft coupling used to increase the distance between shaft ends and give a higher misalignment capability. Cardan shaft coupling with thrust bearings to support the drive line on vertical applications. Combination with a torque limiting device to prevent damage to driving and driven machine under shock loads. Coupling with a brake disc for use on cranes, fans and conveyor drives. RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 86
Coupling Selection Checklist Photocopy this page and complete the following check list to ensure the correct coupling selection is achieved, then fax it to the Renold Hi-Tec Couplings Sales Fax Line below for a speedy response. Customer: Project: Prime mover: (see page 86) Service factor: Driven equipment: (see page 87) Service factor: Continuous power: Maximum power: Operating speed: Overspeed: Driving shaft diameter: Driven shaft diameter: Driving shaft length: Driven shaft length: Flywheel location diameter: Hole size and PCD: Continuous misalignment: Transient misalignment: Diameter constraints: Length constraints: Distance between shaft ends: If you require help with coupling selections contact Renold Hi-Tec Couplings: Tel: +44 (0) 1422 255000 Fax: +44 (0) 1422 255100 RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com 87
Page 1 and 2:
Couplings Resilient and Soft Start
Page 3:
Contents Page No Company Profile 5
Page 6 and 7:
Flexible and Soft Start Couplings -
Page 8 and 9:
Pictorial Contents Spiderflex Coupl
Page 10 and 11:
Gears and Variable Speed Product Ra
Page 12 and 13:
Selection of Couplings Flexible Cou
Page 14 and 15:
Service Factors and Selection Servi
Page 16 and 17:
Range of Taper Bushes Metric Range
Page 18 and 19:
Spiderflex G H1 H2 H2 Assembled len
Page 20 and 21:
Spider F D A B C C Coupling Power T
Page 22 and 23:
Pinflex E F D B C1 C2 C2 Type B Typ
Page 24 and 25:
Pinflex Brakedrum Couplings G H D B
Page 26 and 27:
Crownpin An established pin/buffer
Page 28 and 29:
Crownpin (continued) Component Spar
Page 30 and 31:
Tyreflex Sizes TY40 to TY60 Sizes T
Page 32 and 33:
Tyreflex (continued) Ordering Code
Page 34 and 35:
Discflex E E D A B Type B C F C Typ
Page 36 and 37: Chainflex An all metal flexible yet
Page 38 and 39: Rigid C1 E C2 E C2 E D B A D B D B
Page 40 and 41: Gearflex - Introduction Piloted Cro
Page 42 and 43: Gearflex DA L1 L2 F1 NORMAL F2 POSI
Page 44 and 45: Gearflex SA L F B1 A1 C1 C2 A2 B2 D
Page 46 and 47: Gearflex GFV B1 A1 C1 F L C2 A2 B2
Page 48 and 49: Hydrastart Soft Start - Fluid Coupl
Page 50 and 51: Operating Principles OUTER COVERS D
Page 52 and 53: ‘Soft’ Starting 600 Fig. 3 500
Page 54 and 55: Hydrastart Selection Chart 1000 800
Page 56 and 57: Standard Available Options Non Dela
Page 58 and 59: Hydrastart Pinflex Coupling - Dimen
Page 60 and 61: Hydrastart Gearflex Coupling - Dime
Page 62 and 63: Renold Hi-Tec Couplings Hi-Tec Coup
Page 64 and 65: RB Flexible Coupling General purpos
Page 66 and 67: RB Shaft to Shaft Rigid half / Flex
Page 68 and 69: RB Standard SAE Flywheel to Shaft 0
Page 70 and 71: RB Standard SAE Flywheel to Shaft w
Page 72 and 73: RB Technical Data 1.1 Diesel Engine
Page 74 and 75: RB Technical Data Coupling Nominal
Page 76 and 77: PM Flexible Coupling Heavy duty ste
Page 78 and 79: PM Shaft to Shaft PM 0.4 to PM 130
Page 80 and 81: PM Mill Motor Couplings Mill motor
Page 82 and 83: PM Technical Data 1.1 Prediction of
Page 84 and 85: PM 180 - PM 6000 PM Technical Data
Page 88 and 89: Selection Procedure ● From the co
Page 90 and 91: Selection Examples Example 1 Exampl
Page 92 and 93: Rubber Information The rubber block
Page 94 and 95: Product Range The products comprise
Page 97 and 98: Notes RENOLD Hi-Tec Couplings. Tel:
Page 99 and 100: Worldwide Sales and Services NORWAY
show all

Renold Clutches & Couplings - casa sueca s.a.

Create successful ePaper yourself

Delete template?

Save as template?