Renold Clutches & Couplings - casa sueca s.a.

RB Shaft to Shaft
Rigid half / Flex half
W3
J3
B
J J
S x T
W2
J2
Features
●
Can accommodate a
wide range of shaft
diameters
Benefits
●
Allows the optimum
coupling to be
selected
A
F
E
X
D C D1
Y
G
Q x R
W1
J1
●
●
Easy disconnection of
the outer member
and driving flange
Coupling available
with limited end
float
●
●
Allows the driving
and driven machines
to be disconnected
Provides axial
location for
armatures with axial
float
Coupling
Size A B C D D1 E F G J Q R S T U MAX.X MAX.Y MIN.X&Y
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
0.12 200.0 104.8 3.2 50.8 50.8 79.4 177.8 156.5 12.7 5 M8 6 M8 9.2 50 55 30
0.2 222.2 111.2 3.2 54.0 54.0 95.2 200.0 178 14.3 6 M8 6 M8 9.2 60 70 35
0.24 238.1 123.8 3.2 60.3 60.3 101.6 212.7 186.5 15.9 6 M8 6 M10 11.2 65 75 40
0.37 260.3 136.5 3.2 66.7 66.7 120.6 235.0 210 17.5 6 M10 8 M10 11.2 80 85 40
0.73 308.0 174.6 3.2 85.7 85.7 152.4 279.4 251 19.0 6 M10 8 M12 13.2 95 95 55
1.15 358.8 193.7 3.2 95.2 95.2 184.1 323.8 295 19.0 6 M12 10 M12 13.2 115 115 55
2.15 466.7 233.4 4.8 114.3 114.3 222.2 438.15 362 19.0 6 M12 16 M12 13.2 140 140 70
3.86 508.0 260.4 6.4 127.0 127.0 279.4 469.9 435 22.2 7 M12 12 M16 17.25 170 170 80
5.5 577.8 285.8 6.4 139.7 139.7 330.2 536.6 501.5 25.4 8 M12 12 M16 17.25 210 210 90
Coupling
Size
Rubber Elements Max. Speed (rpm) Weight (3)Kg Inertia (3)Kgm 2 Allowable Misalignment (2)
Per Cavity Per Coupling (1) W1 W2 W3 J1 J2 J3 Radial (mm) Axial (mm) Conical (degree)
0.12 1 10 5250 2.82 4.0 4.06 0.0044 0.0232 0.0153 0.75 1.5 0.5
0.2 1 12 4725 4.04 5.05 5.82 0.0084 0.0375 0.027 0.75 1.5 0.5
0.24 1 12 4410 5.29 6.38 7.42 0.0131 0.0546 0.0396 0.75 1.5 0.5
0.37 1 12 4035 7.49 8.14 10.44 0.0233 0.0887 0.0644 0.75 1.5 0.5
0.73 1 12 3410 12.82 13.29 18.03 0.0563 0.20 0.1475 1.0 1.5 0.5
1.15 1 12 2925 23.39 18.41 27.37 0.1399 0.3674 0.2862 1.5 1.5 0.5
2.15 1 12 2250 35.88 33.98 47.43 0.3227 1.1035 0.7998 1.5 2.0 0.5
3.86 1 14 2070 62.81 43.87 75.39 0.8489 1.9161 1.512 1.5 3.0 0.5
55.5 1 16 1820 102.09 59.0 113.32 1.9633 3.4391 2.9796 1.5 3.0 0.5
(1) For operation above 80% of the declared maximum coupling speed it is recommended that the coupling is dynamically balanced.
(2) Installations should be initially aligned as accurately as possible. In order to allow for deterioration in alignment over time it is
recommended that initial alignment should not exceed 25% of the above noted data. The forces on the driving and driven machinery
should be calculated to ensure that these do not exceed the manufacturers allowables.
(3) Weights and inertias are based on the minimum bore size.
RENOLD Hi-Tec Couplings. Tel: + 44 (0) 1422 255000 Fax: + 44 (0) 1422 320273 E-Mail: sales@hitec.renold.com
66