Renold Clutches & Couplings - casa sueca s.a.
Renold Clutches & Couplings - casa sueca s.a.
Renold Clutches & Couplings - casa sueca s.a.
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Gearflex SA<br />
L<br />
F<br />
B1<br />
A1<br />
C1<br />
C2<br />
A2<br />
B2<br />
D<br />
Coupling Power Torque Speed Bore A1 Bore A2 Dimensions<br />
Size /100rpm Nominal Max** Max* Min Max Min B1 B2 C1 C2 D F L Mass WR 2<br />
Kw Nm rpm mm mm mm mm mm mm mm mm mm mm mm kg kg m 2<br />
GF10SA 14.9 1423 7100 46 14 58 14 60 76 43 40 116 4 87 4.8 0.005<br />
GF15SA 28.2 2693 5400 57 20 75 20 76 98 49 47 152 4 100 8.4 0.019<br />
GF20SA 48 4584 4800 78 27 95 27 102 124 62 60 178 4 125 17.2 0.044<br />
GF25SA 77.6 7411 4250 90 27 110 27 117 148 77 75 213 5 156 29.0 0.107<br />
GF30SA 128 12224 4000 110 39 130 39 143 173 91 89 240 5 185 39.0 0.200<br />
GF35SA 196 18718 3600 127 39 155 39 165 201 106 104 279 6 216 63.5 0.446<br />
GF40SA 312 29796 3290 145 55 180 55 191 233 121 116 318 8 244 93.9 0.842<br />
GF45SA 431 41161 2920 165 55 200 55 216 262 135 130 346 9 274 127 1.350<br />
GF50SA 578 55199 2630 185 55 225 55 241 294 153 148 389 9 310 186 2.800<br />
GF55SA 857 81844 2320 205 55 250 55 267 324 175 164 425 9 348 244 3.940<br />
GF60SA 1096 104668 2120 225 55 265 55 292 349 188 182 457 10 380 299 5.130<br />
GF70SA 1640 156620 1830 260 55 310 55 343 406 221 221 527 13 454 472 11.040<br />
Ordering Code<br />
Misalignment Rating<br />
Angle (degrees) Factor<br />
1.50 1.00<br />
1.00 1.15<br />
0.75 1.30<br />
0.50 1.55<br />
0.00 2.00<br />
Gearflex<br />
Size<br />
GF 40 SA<br />
Catalogue ratings shown are nominal values at 1.50 degrees.<br />
For values at misalignments less than 1.50 degrees:-<br />
Multiply nominal catalogue values by factor in table left.<br />
Single Engagement<br />
Long hub versions available. Contact <strong>Renold</strong> for details. See key stress calculations on Page 14.<br />
<strong>Renold</strong> can supply cardan shaft or torque tube assemblies.<br />
Critical speeds must be checked, please contact <strong>Renold</strong>.<br />
* Maximum Bore - The maximum bores shown are absolute maximums. Under normal circumstances the boss to bore ratio should not be less<br />
than 1.5 for standard applications. Consult <strong>Renold</strong> for overbore approval.<br />
** Speed in excess of these shown may require additional balancing.<br />
RENOLD <strong>Clutches</strong> and <strong>Couplings</strong>. Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 E-Mail: couplings@cc.renold.com<br />
44