Newton Waterproofing Systems Brochure - Barbour Product Search

For more information go to www.barbourproductsearch.info 

Cl/SfB 

Ln6 (L34) 

© John Newton & Co. Ltd. 

Issue Date: February 2012 

Protecting buildings, since 1848 

NEWTON WATERPROOFING SYSTEMS 

Product Catalogue 

100 - Cementitious Products 

200 - Deck And Roofing 

300 - Waterproofing of Concrete Structures 

400 - External Waterproofing 

500 - Cavity Drain Waterproofing 

600 - Flooring Membranes 

700 - Liquid Applied Floor Coatings 

800 - Damp Proofing 

900 - Liquid Primers & Sealers 

FlexProof Construction Joint Waterproofing 

Diathonite Insulating Plaster 

Sump and Pump 

Multi-Use


PRODUCT CATALOGUE 

SYSTEM 100 - CEMENTITIOUS PRODUCTS 

Newton System 100 is a comprehensive portfolio 

of cementitious products which have been 

introduced into our structural waterproofing range 

to complement and complete our basement 

waterproofing designs in areas where the Newton 

System 500 would not be suitable. Such details 

include - lift shafts, flat soffits and externally to 

retained slabs and ring beams. 

Newton 101 F (CW 101), Page 4 

Cementitious Flexible Waterproofing Membrane 

Newton 102 WaterPlug (CW 102), Page 5 

Fast Setting Polymer Compound To Seal Leaks 

Newton 103 SBR (CW 103), Page 5 

Waterproof Additive 

Newton 106 Lime Inhibitor (LC1), Page 5 

Lime Inhibitor for Application to Concrete Surfaces 

Newton 107 QuickFillet (CW 107), Page 6 

Fast Setting Pre-Mix Mortar for Angle Fillets 

SYSTEM 200 - DECK & ROOFING 

A complete range of externally applied elastomeric 

high performance liquid membranes and ancillaries 

for balconies, terraces, flat and inverted roofs, 

podium decks, car parks and reservoirs. This new 

portfolio of seamless and robust liquid membranes 

gives specifiers and specialist waterproofing 

contractors a quick and cost effective solution to 

protect external areas from water ingress. 

Newton RubberFlex System, Page 7 

Podium Deck and Flat Roof Waterproofing System 

Newton 204 Thinner (RF 204), Page 8 

Polyurethane Thinning & Cleaning Agent 

Newton 205 ColorSeal (LM 205), Page 8 

UV Colour Stable Polyurethane Coating 

Newton 207 DeckDrain (M30), Page 9 

Drainage Membrane for Decks and Flat Roofs 

Newton 209 Root Barrier (M32), Page 9 

Puncture Resistant Root Barrier Membrane 

Newton 210 FlexProof-NV (FP4), Page 10 

Waterproofing of Podium Decks and Flat Roofs 

Newton 220 Reservoir (M31), Page 10 

Extensive Green Roof Drainage Membrane 

SYSTEM 300 - WATERPROOFING OF 

CONCRETE STRUCTURES 

Newton System 300 is a range of products, some 

unique to John Newton, used to waterproof construction 

joints and movement joints of retained 

concrete structures so that they become integrally 

waterproof without the need of additional waterproofing 

products, defined within BS8102:2009 as 

Type B waterproofing. 

Newton 301 AquaProof, Page 11 

Metal Construction Joint Water Bar 

Newton 302 InjectionHose, Page 11 

Maintainable Injection Water Bar System 

Newton 303 PolyProof, Page 12 

High Grade Hydrophilic Water Bar 

Newton 304 PolyProof Inject, Page 12 


Newton 305 ActiveJoint, Page 12 

Physical Movement Joint Water Bar 

Newton 306 SwellMastic, Page 13 

Swelling Adhesive 

Newton 307 PipeSeal, Page 13 

Pipe Collar 

Newton 308 Stopaq (SX 108), Page 13 

Unique Hydrophilic Polymer Sealant 

SYSTEM 400 - EXTERNAL WATERPROOFING 

System 400 is a range of products for the 

waterproofing of the outside of earth retained 

structures. Products include sheet membranes for 

the complete envelopment of the raft and walls, 

flexible liquid products for the waterproofing of 

retained walls and composite drainage membranes 

for preventing the build up of ground water to the 

walls or below the raft. Newton System 400 products 

can provide Type A and Type B waterproofing to 

Grades 2 & 3 as defined within BS8102:2009 

Newton 401 FlexProof-X1, Page 14 

Flexible Membrane for Retaining Walls 

Newton 402 Aquabit, Page 15 


Newton 403 HydroBond, Page 15 

Hydrophilic and Bonding Membrane for Raft and 

Wall Waterproofing 

Newton 410 Geodrain, Page 16 

Externally Applied Drainage Membrane 

Note: Please check individual product sheets for advice on appropriate fixings and ancillary products. Contact our Technical 

Department for further information on 020 7237 1217. Copies of our BBA Certificates, Brochures and Data Sheets can be 

downloaded from www.newton-membranes.co.uk. Products and their specifications can be changed or modified without 

prior notice. All copy, diagrams, images and Newton trade names/logos and designs used in this catalogue remain the 

intellectual property of John Newton and Company Ltd. and may not be reproduced without the written permission of the 

Directors of John Newton and Company Ltd. Any party who exploits this property may be subject to prosecution. 

© John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217 

www.newton-membranes.co.uk - info@newton-membranes.co.uk



SYSTEM 500 - CAVITY DRAIN WATERPROOFING 

The professional’s “waterproofing system of 

choice”, Newton System 500 is an internally 

applied waterproofing system based upon our range 

of cavity drain membranes, drainage conduits and 

sophisticated pumping and control systems. Unlike 

conventional ‘tanking’, Newton System 500 is not 

attempting the almost impossible and trying to 

hold water back, but places designed maintainable 

depressurisation voids at known weaknesses in 

the structure so that ingressing water is simply 

captured and diverted out of the property. 

Wall Membranes 

Newton 503 (M5), Page 17 

Newton 503 Mesh (M11 & M12), Page 17 

Newton 508 (M1 & M2), Page 18 

Newton 508 Mesh (M3), Page 18 


Drainage System 

Newton Basedrain (D1), Page 18 

SYSTEM 600 - FLOORING MEMBRANES 

Newton System 600 is a range of HDPE and 

HDPP flooring membranes offering a complete 

damp proof solution for both commercial and 

domestic flooring applications. As well as 

providing protection from dampness within the 

floor, our membranes ‘de-couple’ the floor finish 

from the substrate preventing damage due to 

substrate movement and cracking. Newton damp 

proof membranes can be installed over existing 

and ‘green’ concrete. In addition, our flooring 

membranes are a popular solution for dealing with 

inherent hydrocarbons or ground gas problems. 

Newton flooring membranes can accommodate a 

variety of finishes including timber floors, screeds 

and direct tiles. 

Flooring Membranes 

Newton 601 Slimline (M6), Page 19 

Newton 603 (M23), Page 19 

Newton 603 Mesh (M24 & M25), Page 20 

SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS 

System 700 is a range of liquid applied protective 

and decorative internal flooring products. These 

products are fast curing and available in a 

variety of colours, and are typically used for the 

refurbishment and protection of commercial and 

domestic floors. 

Newton 701 HB (LM 701), Page 21 

High Build Epoxy Floor Coating 

Newton 702 EcoSeal (LM 702), Page 21 

Highly Resistant Polyurethane Floor Coating 

SYSTEM 800 - DAMP PROOFING 

Newton System 800 is a range of BBA approved 

damp proof membranes and ancillaries which are 

quick and clean to install and offer a permanent 

solution for damp proofing walls. The meshed 

membranes provide a firm key and impermeable 

barrier on any damp or deteriorating surface ready 

for plaster, render or dot & dab plasterboard. The 

un-meshed Newton 803 is used where insulation 

requirements dictate the use of a timber or steel 

frame ready for plasterboard. Quick, clean and 

proven to work, Newton damp proof membranes 

offer a permanent and cost effective damp 

proofing solution. 

Damp Proofing Membranes 

Newton 805 Newlath (M9 & M10), Page 22 


Newton 803 Newtonite (M16, M21, M22), Page 23 

Newton 801 FlexProof-X1 Wet Room Waterproofing, 

Page 23 

Damp Proofing Ancillaries 

Newton 800 Mesh Plug (A16), Page 24 

Newton MultiPlug (A1), Page 24 

Newton 800 Cob Plug (A17), Page 24 

Newton 800 Newtonite Plugs (A20), Page 24 

Newton 800 Mastic (A18), Page 25 

Newton Mesh Tape (A25), Page 25 

Newton Overtape (A8), Page 25 

Newton 800 Profile (A19), Page 25 

SYSTEM 900 - LIQUID PRIMERS & SEALERS 

Newton’s high performance range of liquid applied 

products are used in conjunction with System 200 

and 700 liquid membranes. They act as priming 

agents for a variety of substrates prior to the 

application of our specialist waterproofing and 

flooring membranes. 

Newton 901 Humidity Primer (PS 901), Page 26 

Epoxy Primer Suitable for High Humidity Substrate 

Newton 902 (PS 902), Page 26 

Liquid Applied Radon, Gas & Vapour Barrier 

Newton 903 PU Primer (PS 903), Page 27 

Epoxy Primer for Nonporous Substrate 

Newton 904 HP Accelerant (PS 904), Page 27 

Humidity Primer Accelerant 

Newton 906 Mould Stop (PS 906), Page 27 

Mould Steriliser & Killer 





NEWTON FLEXPROOF - CONSTRUCTION 

JOINT WATERPROOFING 

Newton FlexProof-X1 forms an elastomeric polymer 

membrane that is rainproof in minutes and 

capable of handling severe building movements 

and deformations. FlexProof-X1 is quite unique 

with amazing characteristics allowing it to be used 

without a primer, without mixing and in weather 

conditions that preclude the use of alternatives. 

Newton FlexProof-X1 (FP1), Page 28 

Construction Joint Waterproofing 

NEWTON DIATHONITE - INSULATING PLASTER 

Newton Diathonite is a premixed plaster, fibrereinforced 

with cork (granular 0-3 mm), clay 

powders and NHL 3.5 natural hydraulic lime. 

The resulting natural compound produces a plaster 

with unrivalled thermal and acoustic properties that 

is both hard wearing and flexible which is ideal for 

both internal and external applications. 

Newton Diathonite, Page 29 

Eco Thermal Plaster with Insulation and Acoustic 

Properties 

SUMP AND PUMP 

Newtons have an extensive range of submersible 

pumps and pumping ancillaries. We supply the 

highest quality pumps available in each class, 

for the control of clean ground water, grey water, 

effluent or sewage. 

Clean/Ground Water Pumps 

Newton NP150 (P1), Page 30 

Newton CP250 (P31), Page 30 


Newton NP400 (P2 & P3), Page 31 

Newton NP400PP (P13), Page 31 

Newton NP400LLPS (SP1), Page 31 


Newton NP750 (P5 & P6), Page 32 

Effluent Pumps (Not Sewage) 

Newton NP400W (P4), Page 32 

Sewage Pumps 

Newton SP750 Ranger (P9), Page 33 

Newton Flygt DXG (Grinder) (P14 & P16) Page 33 

Sewage Lifting Station 

Trojan Sewage Pumping System (TR1-TR12), Page 33 

Clean/Ground/Effluent Pumping Systems 

Titan-Pro White (TPW), Page 34 

Titan-Pro Green (TPG), Page 34 

Newton Titan-2 (T1-T10), Page 34 

Pumping Ancillary Products 

Newton Control Panel Pro (CP2), Page 35 

Newton High Water Level Alarm (PA50), Page 35 

Newton Dialer (PA5, PA6, PA7), Page 35 

Newton 1200w Power Converter (C1 & C3), Page 36 

Newton 3000w Power Converter (C2 & C4), Page 36 

Newtons can also provide a wide range of specialist 

submersible pumps and sump chambers which 

can be tailor made for site-specific conditions. For 

further information call our technical department 

on 020 7237 1217 

MULTI-USE 

The Multi-Use section is home to products that 

are used within more than one of our systems. 

WaterSeal Tape, for example, can be used with 

System 300, System 400, System 500, System 600 

and System 800. 

Newton Mesh Tape (A25), Page 37 

Newton Overtape (A7, A8, A9), Page 37 

Newton WaterSeal Rope (A6 & A6W), Page 37 

Newton WaterSeal Tape (A5 & A5W), Page 38 

Newton MultiPlug (A1), Page 38 

Newton NuSeal Plugs (A2 & A3), Page 38 




SYSTEM OVERVIEW 

NEWTON SYSTEM 100 

Cementitious Products 

NEWTON SYSTEM 100 - CEMENTITIOUS PRODUCTS 

System Overview 

Newton System 100 is a comprehensive portfolio of Type A 

(BS8102:2009) cementitious waterproofing products for the sealing of 

leaks and the waterproofing of lift shafts, flat soffits, walls and slabs. 

System 100 products can be used on their own, or in conjunction with 

System 200, System 300, System 400 and System 500 waterproofing 

products, and with System 700 (Liquid Flooring Membrane) and System 

800 (damp-proofing) products also. 

NEWTON 101F (CW 101) 

Cementitious Flexible Waterproofing Membrane 

Newton 101F is a two-component acrylic modified cementitious coating. 

It is the ideal product to waterproof and re-surface concrete and masonry. 

101F is a hard wearing, seamless waterproofing solution which is very 

user friendly with simple on-site mixing methods. 

Newton 101F is applied in two coats 1mm each to provide a total 

thickness of 2mm. Each 1mm coat requires a coverage rate of 

1.8kg per m² to give a total coverage rate of 3.6kg per m². Newton 101F 

is supplied in two components of 1 x 25kg tub of powder and 10kg of 

liquid additive (35kg pack) which will cover 9m² - 10m² 

Typical Applications: 

• Waterproof lining for lift pits, swimming pools etc 

• Bathroom and wet areas 

• Waterproof coating for roofs 

• Internal application to flat concrete soffits in conjunction with 

Newton System 500 

• Slurry application to form waterproof bunds 

• Lining existing concrete sump chambers 

• Protection of steels against carbonation and chloride attacks 

Page 4 


www.newton-membranes.co.uk - info@newton-membranes.co.uk 

J o h n N e w t o n L t d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o . u k





NEWTON 102 WATERPLUG (CW 102) 

Fast Setting Polymer Compound To Seal Leaks 

Newton 102 WaterPlug is a fast setting, polymer compound that instantly 

stops running water or seepage through masonry or concrete substrates. 

It becomes harder and more resistant when subjected to constant water 

pressure. Newton 102 WaterPlug is a non-shrink material that expands 

slightly and sets in approximate 2 minutes. Available in 5kg, 10kg or 

25kg tubs. 


• Leak sealing prior to tanking with Newton 101F 

• Sealing of leaks at wall/floor junctions 

• Sealing of leaking mortar joints 

• Leak sealing of cracks in masonry or concrete 

• Repair of construction faults such as honeycombing 

• Anchoring of bolts or posts 

• Controlling water ingress during sump installations 

NEWTON 103 SBR (CW 103) 

Waterproof Additive 

Newton 103 SBR is a high quality liquid, water-based high solids 

styrene butadiene polymer latex with high bonding and waterproofing 

characteristics. It is stable under wet alkaline conditions forming a 

reinforcing polymer matrix within cementitious mixes. Available in 5kg, 

10kg and 25kg 


• Surface waterproofing • Lift shafts 

• Waterproof screeds • Wall/floor junction fillets 

NEWTON 106 LIME INHIBITOR (LC1) 

Lime Inhibitor For Application To Concrete Surfaces 

Newton 106 Lime Inhibitor is applied to concrete surfaces prior to the 

installation of a Newton System 500 cavity drain membrane waterproofing 

system to prevent the ‘leaching’ of free lime from the concrete. Primarily 

designed to be used to new concrete structures, Newton Lime Inhibitor 

should also be used to treat the following areas: newly formed concrete 

walls, kickers and underpins, treatment to cut recesses prior to Basedrain 

installation and as a concrete additive to newly formed sump chambers. 

Supplied in 1kg units - Newton 106 is a concentrated mix to be added 

1 part Newton 106 Lime Inhibitor to 9 parts clean water. Newton 106 

should be applied in this 10 litre mix through a course sprayer and will 

cover a maximum of 100 sq m² 

Product Features: 

• Solvent and caustic free • Easy to use and handle 

• Non-hazardous (on dilution) • Long term durability 

• Compatible with alkaline substrates 

Page 5 








NEWTON 107 QUICKFILLET (CW 107) 

Fast Setting Pre-Mix Mortar For Angle Fillets 

Newton 107 QuickFillet is a fast setting and fast curing mortar with a 

rapid strength gain used to quickly form 45° angled fillets at junctions 

between walls and floors or soffits. Newton 107 QuickFillet should be 

used to form fillets for use with Newton 101F cementitious slurry and 

can be used to reinforce internal corners ready for Newton liquid applied 

membranes such as 201 RubberFlex, 205 ColorSeal or 702 EcoSeal. 

Newton 107 Quick Fillet can also be used to repair substrate prior to the 

use of Newton System 900 primers. 

Newton 107 QuickFillet is supplied in 25kg tubs and when correctly mixed 

with 3.6 litres of clean water should cover approx 30 linear metres applied 

in a 25mm x 25mm fillet 


• Creation of angle fillets 

• Surface repairs to substrate prior to application of Newton System 

900 floor primers 

Page 6 


J o h n N e w t o n L t d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o . u k 





Deck & Roofing 

NEWTON SYSTEM 200 - DECK AND ROOFING 


Newton System 200 is a complete range of externally applied liquid 

elastomeric membranes for the structural waterproofing of podium decks, 

balconies and terraces, flat and inverted roofs, car parks, swimming 

pools, green or turf roofs and reservoirs. This new portfolio of seamless 

and robust liquid membranes gives specifiers and specialist waterproofing 

contractors a quick and cost effective solution to protect external areas 

from water ingress. 

NEWTON RUBBERFLEX SYSTEM 

Podium Deck and Flat Roof Waterproofing System 

Newton RubberFlex is a BBA Certified single part liquid waterproofing 

material, which forms an elastomeric polyurethane membrane, resisting 

UV rays and capable of handling severe building movements and 

deformations. Newton RubberFlex is guaranteed against deterioration 

for 25 years and is supported by BBA Certification Certificate Number 

11/4840. Newton RubberFlex can be specified as a UV stable 

waterproofing membrane with high resistance to impact and abrasion 

or can be the primary waterproofing barrier when used with Newton 

207 DeckDrain drainage membrane to create a complete drained 

waterproofing solution. 

Newton RubberFlex is available in three variants, the choice of which 

would be dependent on the required speed of application between coats 

as well as on the temperature and humidity at the time of installation and 

the type and height of up-stand to be installed. 

Newton 201 RubberFlex 

Self levelling with standard cure times used for horizontal surfaces and 

up-stands of up to 250mm with reinforcement. 

Newton 202 RubberFlex-QC 

Quick Curing derivative with fast cure times used for horizontal surfaces 

and up-stands of up to 250mm with reinforcement. 

Newton 203 RubberFlex-V 

Thixotropic variant for larger vertical areas. 

Newton RubberFlex can be applied either as a reinforced or a nonreinforced 

system depending on substrate type or substrate quality. See 

product datasheet for more details. 

Application rates: 25kg is sufficient to cover 12.5m 2 of surface with a two 

coat treatment of 2kgs per m 2 providing an overall membrane thickness 

of 1.9mm (refer to data sheets for suggested drying times between coats) 

Specialist application equipment such as spiked rollers are available 

on request. 

201 RubberFlex and 202 RubberFlex QC are available in 10kg and 25kg 

tins. 203 RubberFlex-V is available in 10kg tins. 

Page 7 








NEWTON 204 THINNER (RF 204) 

Polyurethane Thinning & Cleaning Agent 

Newton 204 Thinner is a slow acting blended solvent for use with Newton 

RubberFlex and Newton 205 ColorSeal. Newton 204 Thinner is used to 

dilute the polyurethane membrane and is especially useful when Newton 

RubberFlex is applied by airless spray. 

Newton 204 Thinner is also used as a cleaning medium for tools and 

equipment used during the application of the membrane and it can 

also be used as a barrier against humidity when having to store product 

already opened. Newton 204 Thinner is supplied in 4kg, 9kg and 20kg 

containers. 

Newton 204 Thinner is also used for cleaning tools used with Newton 

Flexproof products. 


• Cleaning of tools and equipment 

• Increasing viscosity of membranes for application by airless spraying 

• Sealing of product against moisture in opened containers 

NEWTON 205 COLORSEAL (LM 205) 

UV Colour Stable Polyurethane Coating 

Newton 205 ColorSeal is a UV stable, single component, protective 

polyurethane resin top-coat. 205 ColorSeal provides a transparent hard 

wearing coating, or it can be coloured with the addition of pigmented quartz 

sand to provide a textured, slip resistant, UV colour stable finish. Its primary 

use is as a UV stable and hard wearing protection coat above the Newton 

RubberFlex podium deck and flat roof waterproofing system. 

The exceptional strength and durability means that Newton 205 ColorSeal 

can also be used as a stand-alone flooring product. It cures to a gloss 

finish. For pedestrian walkways it is recommended that a coloured quartz 

sand is applied to the still tacky first coat of 205 ColorSeal to give a nonslip 

surface. Newton 205 ColorSeal is supplied in 4kg, 9kg and 20kg 

containers. 

Coverage: a 4kg pack is sufficient to cover a prepared surface area of 13m 2 

with the recommended covering of 0.3kg/m 2 providing an overall thickness 

of 250-400 microns. With a two coat application which includes the quartz 

sand anti-slip layer, coverage will be 6m 2 with the recommended two 

coat treatment 


• Heavy traffic areas 

• Industrial factories, depots and warehouses 

• UV colour stable and non-slip finish to other floor coatings 

Page 8 








NEWTON 207 DECKDRAIN (M30) 

Drainage Membrane for Decks and Flat Roofs 

Newton 207 DeckDrain is a double cuspated, deck and flat roof drainage 

membrane, that incorporates a non-woven geotextile filter layer, bonded to 

a water impermeable HDPE (High Density Polyethylene) core. The double 

cuspated design provides two layers of drainage; allowing for primary 

drainage through the geotextile filter, as well as secondary drainage between 

the underside of 207 DeckDrain and the primary waterproofing layer. 

The lower drainage layer eliminates the risk of trapped water, a problem 

associated with conventional single cuspated deck drainage membranes. 

Newton 207 DeckDrain is supplied in 1.1m wide x 25m long rolls and is 

simply laid above the waterproofing membrane with the geotextile fleece 

uppermost. 


As the drainage layer above a deck, balcony or flat roof waterproofing 

membrane such as Newton 201 RubberFlex, particularly where: 

1. Block paviours or flooring slabs are bedded on sand as the surface finish. 

2. Soil filled planters are included to the deck or flat roof. 

Also suitable for use as a vertical drainage layer when used as part of 

a professionally designed and installed externally applied basement 

waterproofing system. 

NEWTON 209 ROOT BARRIER (M32) 

Puncture Resistant Root Barrier Membrane 

Newton 209 RootBarrier is designed to eliminate root penetration. It 

consists of an impermeable High Density Polyethylene (HDPE) membrane, 

providing robust root-proof protection to the primary waterproofing 

membrane to green roofs or planters where intrusive root systems are 

present. 

The membrane has high tensile strength and puncture resistance 

and provides an efficient, reliable and cost effective barrier to provide 

protection against Japanese Knotweed and other aggressive root systems. 


As a root barrier to protect the waterproofing membrane from root damage 

within intrusive green roof systems or planters. 

Newton 209 RootBarrier is supplied in 1.2m wide x 50m long rolls and is 

placed above the waterproofing membrane and the Newton 207 DeckDrain 

(if included in the design). Joints are overlapped by at least 150mm and 

sealed with two lines of Newton Waterseal Tape. 

Page 9 








NEWTON 210 FLEXPROOF-NV (FP4) 

Waterproofing of Podium Decks and Flat Roofs 

Newton 210 FlexProof-NV is a highly advanced single component liquid 

waterproofing material, which forms an elastomeric polymer membrane 

capable of handling severe building movements and deformations. 

Movement joints to Decks and Flat Roofs can also be waterproofed with 

Newton 201 FlexProof-NV whether the main waterproofing membrane is 

FlexProof-NV or Newton RubberFlex. 

Newton 210 FlexProof-NV has characteristics that allow it to be used 

without a primer, without mixing and in weather conditions that preclude 

the use of alternatives. With a tight project timescale, 210 FlexProof-NV 

can be relied upon to ensure the project is completed on time. 

Newton 210 FlexProof-NV can be used as the primary waterproofing 

membrane below a number of hard finishes and drainage options and 

when partnered with Newton 207 DeckDrain drainage membrane, creates 

a complete drained waterproofing solution to your deck, terrace or flat roof. 

Newton 210 FlexProof-NV is supplied in 7.5kg and 26kg containers and is 

applied to the deck or roof with a squeegee or trowel and is simply poured 

into movement joints. 


• Waterproofing of podium decks, balconies, terraces and flat roofs. 

• As the primary waterproofing membrane below a green roof. 

• As the waterproofing membrane within a warm roof specification. 

• Waterproofing of planters 

NEWTON 220 RESERVOIR (M31) 

Extensive Green Roof Drainage Membrane 

Newton 220 Reservoir is a unique drainage and water retention 

membrane for use where a water reservoir is required for extensive green 

roofs of sedum, herbaceous plants, mosses or grass above decks and 

roofs. 

Unlike other products of this type, Newton 220 Reservoir has a bonded 

geotextile that prevents intrusion of the soil into the water holding cups 

during back-fill and compression. This results in a permanently larger 

volume reservoir than any other 20mm deep green roof membrane. 

When the water holding cups are full, the large drainage holes within the 

HDPE core allow water to easily pass through to the drainage layer below 

to prevent saturation and water logging of the green roof above. 


As a water holding and drainage layer above a deck, flat roof or pitched 

roof where shallow planting is used to create an extensive green roof. 

Newton 220 Reservoir is supplied in 0.92m wide x 50m long rolls and is simply 

laid above the waterproofing membrane with the geotextile fleece uppermost. 

Page 10 







Waterproofing of Concrete Structures 


WATERPROOFING OF CONCRETE STRUCTURES 


Newton System 300 is a range of products, some unique to John Newton, 

used to waterproof construction joints and movement joints of retained 

concrete structures so that they become integrally waterproof without the 

need of additional waterproofing products, defined within BS8102:2009 

as Type B waterproofing. 

Waterproofing can be further enhanced by the addition of Type A (Newton 

System 100 or System 400) or Type C (Newton System 500) waterproofing 

systems to provide a combined waterproofing approach, recommended 

by BS8102:2009 when absolute waterproofing security is required. 

The podium deck of a retained concrete structure would also require 

waterproofing with one of our System 200 products. 

NEWTON 301 AQUAPROOF 

Metal Construction Joint Water Bar 

Newton 301 AquaProof is a coated metal water bar system used for the 

sealing of construction joints within retained concrete structures. 

Newton 301 AquaProof features an adhesive, reactive 

polymer coating on one of its sides. The coating creates a permanent 

watertight seal with the surrounding concrete to create a water bar that 

works immediately. 

Newton 301 AquaProof is supplied in 6m rolls and is fitted to the 

reinforcing steel with Omega Clips prior to the placing of the concrete. 


• The waterproofing of construction joints to poured concrete elements 

of earth retained structures. 

NEWTON 302 INJECTIONHOSE 

Maintainable Injection Water Bar System 

Newton 302 InjectionHose is a high performance injectable water bar 

system used for the sealing of construction joints within retained concrete 

structures. 

The system offers many benefits over conventional water bars, 

especially its ability to grout poorly compacted concrete and by offering a 

maintainable solution that allows for resealing of the construction joint, 

post construction. 

Newton 302 InjectionHose is supplied in reels of 120m and is applied to 

an already formed concrete element prior to formation of the joint. 


• Post construction grouting and leak sealing of construction joints to 

poured concrete earth retained structures. 

Page 11 








NEWTON 303 POLYPROOF 


Newton 303 PolyProof is a very high grade hydrophilic water bar which 

seals gaps in construction joints by swelling up to 400% its original size. 

The water bar is adhered to the face of the first pour of the joint with 

either Newton 306 SwellMastic or Newton 309 Contact Adhesive. Can 

also be used as the water bar in settlement or compression joints. 

303 PolyProof is available in the following sizes: 

Depth Width Length 

303 PolyProof-2 2mm 20mm 25m 




• Waterproofing of static construction joints, settlement joints and 

compression joints to concrete earth retained structures. 

NEWTON 304 POLYPROOF INJECT 


Unique construction joint water bar that combines the high performance 

swelling capabilities of Newton 303 PolyProof and the post construction 

injection of grouts and resins provided by Newton 302 InjectionHose. 

Newton 304 PolyProof Inject is supplied in coils of 60m and is 

mechanically fixed to the construction joint with special clips. 


• Waterproofing using hydrophilic swelling and post construction 

grouting and leak sealing of construction joints to poured concrete 

earth retained structures. 

NEWTON 305 ACTIVEJOINT 

Physical Movement Joint Water Bar 

MDPE physical water bar for the waterproofing of movement joints. The 

water bar has a unique ‘V’ shape with a number of barbs so that water 

pressure expands the joint, creating more grip to the concrete joint as the 

pressure increases. 

Newton 305 ActiveJoint is supplied in eight widths to waterproof 

movement joints from between 25mm to 100mm. The product is simply 

hammered into a movement joint that has been lubricated with Newton 

306 SwellMastic, which is hydrophilic and will swell in contact with water 

to further waterproof the joint. 


• Waterproofing of movement joints. 

Page 12 








NEWTON 306 SWELLMASTIC 

Swelling Adhesive 

Newton 306 SwellMastic is a high performance mastic used to adhere 

Newton 303 PolyProof and Newton 305 ActiveJoint to the concrete joint. 

Can also be used to seal around protrusions such as pipes and conduits 

and should be used to reinforce Newton 307 PipeSeal being fitted to 

pipes passing through the structure. 

Newton 306 SwellMastic is supplied in cartridges of 290ml and foil 

sausages of 600ml and is applied in a bead. 


• Sealing around protrusions through the structure such as service 

pipes and as an adhesive for Newton 303 PolyProof, 304 PolyProof 

Inject and 305 ActiveJoint. 

NEWTON 307 PIPE SEAL 

Pipe Collar 

Newton 307 PipeSeal is a preformed MDPE seal that creates a physical, 

flanged joint around pipes passing through the structure. Newton 306 

SwellMastic should be used to reinforce the joint. 

Newton 307 PipeSeal is available for sealing pipes of diameters of 

110mm and 160mm and they are simply slipped over the pipe using 

neutral soap as a lubricant. 


• Sealing around pipes protruding through the structure. 

NEWTON 308 STOPAQ (SX 308) 

Unique Hydrophilic Polymer Sealant 

Newton 308 Stopaq is a unique swelling sealant compound system 

which provides a waterproofing solution for the notoriously difficult to seal 

service pipe penetrations through retaining walls. 

Newton 308 Stopaq is supplied in 0.53kg tubes and is applied with a 

specialist applicator gun. The product cartridge needs to be warmed prior 

to installation by submersing in warm water. 


• Sealing around cables, conduits and other difficult to seal protrusions 

through the structure whether in sleeve pipes or directly through the 

concrete. 

Page 13 







External Waterproofing 

NEWTON SYSTEM 400 - EXTERNAL WATERPROOFING 


System 400 is a range of products for the waterproofing of the outside 

of earth retained structures. Products include sheet membranes for the 

complete envelopment of the raft and walls, flexible liquid products for the 

waterproofing of retained walls and composite drainage membranes for 

preventing the build up of ground water to the walls or below the raft. 

Newton System 400 products can provide Type A and Type B 

waterproofing to Grades 2 & 3 as defined within BS8102:2009 Code of 

Practice for the Protection of Below Ground Structures Against Water from 

the Ground. 

NEWTON 401 FLEXPROOF-X1 


Newton 401 FlexProof-X1 is a highly advanced single component liquid 


that is rainproof in minutes and capable of handling severe building 

movements and deformations. 

401 FlexProof-X1 has characteristics that allow it to be used without a 

primer, without mixing and in weather conditions that preclude the use of 

alternatives. 

Newton 401 FlexProof-X1 comes in containers of 15kg & 26kg which is 

applied by trowel in one coat of 3kg/m 2 . 

Suitable Substrate: 

• Concrete or masonry retained walls. 

Key Benefits 

• No mixing required – simply open the packaging and use. 

• Can be used in sub-zero temperatures and on slightly damp 

substrate. 

• No primer required – saving on primer and labour costs 

• Single coat application. 

• 100% waterproof, but allows vapour diffusion. 

• Very flexible – Resistant to movement and fissures in substrates. 

• Excellent adhesion to suitable substrates. 

• Resistant to temperature variations maintaining its characteristics 

between -40ºC & 90ºC. 

• Excellent resistance to the high alkalinity of concrete 

• Page 14 








NEWTON 402 AQUABIT 


Newton 402 Aquabit is a single component water based waterproofing 

bituminous mortar that includes polystyrene micro-spheres that allow it 

to be applied obtaining a level of thickness up to 3mm, modified to make 

the product extremely workable and able with just one coat to fill surface 

irregularities, typical on concrete foundation walls. The material is also 

characterised by a high elasticity, crack bridging ability and a good salt 

resistance. It can be applied both on old and new walls. 

Newton 402 Aquabit comes in containers of 25 litres which is applied by 

trowel in one coat of 2.2 litres per m 2 to give an average thickness 

of 2.5mm. 


• Waterproofing of retained walls 

NEWTON 403 HYDROBOND 

Hydrophilic and Bonding Membrane for Raft and Wall Waterproofing 

Newton 403 HydroBond is a very high performance composite sheet 

membrane that features a locking fleece to one side and a polymer 

hydrophilic coating to the other side. 

When placed below the new raft or against the wall shuttering, the 

poured concrete engages into the locking fleece so that the membrane is 

completely locked in and monolithic to the concrete thus ensuring that if 

a leak did occur it cannot track to the construction joints. The hydrophilic 

coating seals small holes that may be accidentally formed during fixing of 

the reinforcing steel or the pouring or compaction of the concrete. 

Newton 403 HydroBond is supplied in rolls of 2m x 30m and can be laid 

to the blinding and shuttering of a raft construction or adhered to already 

formed retaining walls. 


• Waterproofing of retained walls 

• Waterproofing of decks 

Page 15 








NEWTON 410 GEODRAIN (M18) 

Externally Applied Drainage Membrane 

Newton 410 Geodrain is a component drainage sheet consisting of a 

non-woven geotextile filter layer thermally welded to a water impermeable 

HDPE drainage membrane. Newton 410 Geodrain provides outstanding 

drainage and protection to the outside face of basement walls, preventing 

the build-up of water pressure and protecting the structure from 

aggressive water, chemicals and toxins. 

Newton 410 Geodrain comes in rolls which are 2m x 12.5m with a surface 

coverage of 25m 2 (in-line studs 10mm in depth) 


• As the drainage layer of an externally applied waterproofing system 

when used in conjunction with sheet applied or liquid applied external 

tanking membrane to BS8102:2009 

• Protection of the structure from aggressive chemicals in the ground water 

• To prevent the build up of ground water to retaining walls 

Page 16 







Cavity Drain Waterproofing 

NEWTON SYSTEM 500 - CAVITY DRAIN WATERPROOFING 


The professional’s “waterproofing system of choice”, Newton System 500 

is an internally applied waterproofing system based upon our range of 

cavity drain membranes, drainage conduits and sophisticated pumping 

and control systems. 

Unlike conventional ’tanking’, Newton System 500 is not attempting the 

almost impossible and trying to hold water back, but places designed 

maintainable depressurisation voids at known weaknesses in the 

structure so that ingressing water is simply captured and diverted out 

of the property. Newton recommends that our structural waterproofing 

systems are installed by one of our Nationwide Network of Newton 

Specialist Basement Contractors who have been trained by Newton 

and can offer full professional indemnity on design and insured backed 

guarantee on the installation. 

NEWTON 503 (M5) 

3mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits 

Newton 503 is a BBA approved cavity drain waterproofing membrane 

suitable for use internally to retaining walls, vaulted soffits and floors. 

Newton 503 is a flexible HDPE membrane which at 0.5mm in thickness 

provides a low profile drainage solution within the Newton Cavity Drain 

membrane range. 

Newton 503 (M5) is available in rolls 2m x 20m - 40m 2 

NEWTON 503 MESH (M11 & M12) 


Newton 503 Mesh is a BBA certified meshed membrane suitable for use 

as a waterproofing membrane when used below the ground as part of 

Newton System 500. 

With its 3mm stud, Newton 503 Mesh is just 3.5mm in overall thickness, 

and is the preferred meshed membrane where space is at a premium. 

Its meshed surface provides an excellent ’key’ for lime mortars, renders, 

plasters or dabbed plasterboard. When using Newton 503 Mesh, it is 

essential to use Newton MultiPlug or Newton NuSeal with WaterSeal Rope 

as a means of achieving a waterproof seal. 

Newton 503 Mesh is available in roll sizes 1m x 20m - 

20m 2 (M12) and 2m x 20m - 40m 2 (M11) 

Page 17 







Cavity Drain Waterproofing 

NEWTON 508 (M1 & M2) 


Newton 508 is our high quality BBA approved cavity drain waterproofing 

membrane suitable for use internally below the ground to retaining walls, 

vaulted soffits and floors. Newton 508 is our flagship membrane and one 

of the most specified cavity drain membranes in the UK. The 0.7mm thick 

HDPE product allows for large industrial loads to be applied and the in line 

studs allow for quick installation with minimal surface preparation. 

Newton 508 is available in roll sizes 2.4m x 20m - 48m 2 

(M1) and 2m x 20m - 40m 2 (M2) 

NEWTON 508 MESH (M3) 

8mm Meshed Cavity Drain Membrane for Basement Walls, 

Floors & Vaulted Soffits 

Newton 508 Mesh is a BBA approved meshed cavity drain waterproofing 

membrane, suitable for use internally below the ground to retaining walls 

and vaulted soffits. Newton 508 Mesh is typically used where space 

prevents the use of a dry-lining frame or block wall as the wall finish 

or where a direct rendered or plastered finish is preferred. The ability 

to apply direct finishes to the product makes it ideal for convoluted or 

confined basement areas where space is at a premium or where the 

original contours (features) of the property need to be retained. 

Newton 508 Mesh (M3) is available in rolls 2m x 20m - 

40m 2 

NEWTON 520 (M4 & M13) 

20mm Cavity Drain Membrane for Basement Floors 

Newton 520 is a BBA approved cavity drain membrane suitable for use 

above basement floor areas. The 20mm studded membrane allows for 

a massive flow rate to pass underneath the membrane and is specified 

where floor areas are of questionable quality or where it is anticipated 

that there may be a risk of severe water penetration. 

Newton 520 is available in roll sizes 2m x 20m - 40m 2 

(M4) or 2m x 10m - 20m 2 (M13) 

NEWTON BASEDRAIN (D1) 

Drainage System 

Newton Basedrain comprises a range of products that receive water 

ingressing at weaknesses within the structure and then discharge the 

collected water to a Newton Sump System or safe drainage (drainage that 

is below the level of the basement floor that cannot back-up or block). 

Basedrain is supplied in packs of 12 linear metres (6 x 2m) lengths. 

Internal and external corners, T pieces, drainage connectors and access/ 

jetting ports should be utilised with Basedrain. Contact us for more details. 

Page 18 








NEWTON SYSTEM 600 - FLOORING MEMBRANES 


Newton System 600 is a range of HDPE and HDPP flooring membranes 

offering a complete damp proof solution for both commercial and 

domestic flooring applications. As well as providing protection from 

dampness within the floor, our membranes ‘de-couple’ the floor finish 

from the substrate preventing damage due to substrate movement and 

cracking. Newton damp proof membranes can be installed over existing 

and ‘green’ concrete. 

In addition our flooring membranes are a popular solution for dealing 

with inherent hydrocarbons or ground gas problems. Newton flooring 

membranes can accommodate a variety of finishes including timber 

floors, screeds and direct tiles. 

NEWTON 601 SLIMLINE (M6) 

Flat Loose Laid High Grade Flooring Membrane 

Newton 601 Slimline is a high-grade flooring membrane used primarily for 

isolating moisture sensitive flooring from dampness in the floor slab, but 

can also be used as the floor membrane as part of Newton System 500 

when the survey has ascertained that no risk of water entering through 

the body of the slab exists. 

Newton 601 Slimline allows for the installation of sensitive flooring to 

be laid above ’green’ still curing concrete as soon as the concrete is 

walkable, usually two days, significantly reducing project times. With a 

loading capability of over 1000kN/m 2 , Newton 601 Slimline is able to 

resist very high compressive loading and is suitable for use as a high 

load DPC within structural block walls, especially when used to connect 

the wall and floor membranes within Newton System 500. Newton 601 

Slimline is made from HDPP and is the thinnest profile membrane within 

the Newton floor membrane portfolio. 

Newton 601 is available in rolls 2.07m x 20m - 40m 2 (M6) 

NEWTON 603 (M23) 

3mm Loose Laid Flooring Membrane 

Newton 603 is suitable for use above new and existing floors. The 3mm 

studs allow for pressure equalisation of dampness within the floor below 

allowing for dissipation at room perimeter and subsequent drying of the 

floor. The studs also give slight compression to footfall making the floor 

very responsive and comfortable and ideal as the floor membrane for 

performance sports floors. Newton 603 uncouples the floor finish from 

the substrate so that movement is not transferred to the floor finish 

above. The membrane also bridges small cracks allowing for quick floor 

installation above less than ideal substrate. 

Newton 603 is available in rolls 2m x 20m - 40m 2 (M23) 

Page 19 








NEWTON 603 MESH (M24 & M25) 

Loose Laid 3mm Flooring Membrane with Meshed Surface 

Newton 603 Mesh is high grade flooring membrane with an installation 

height of 3.5mm. The white HDPE cuspated core has a polyethylene mesh 

above allowing for adhesion of the floor finish to the membrane. 

Newton 603 Mesh is loose laid above the substrate and is therefore 

uncoupled from the floor ensuring that the floor finish is not affected by 

movement or cracking of the substrate. 

Newton 603 Mesh is available in rolls 1m x 20m - 20m 2 (M24) and 

2m x 20m - 40m 2 (M25) 

Page 20 







Liquid Applied Floor Coatings 

NEWTON SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS 


System 700 is our range of liquid applied protective and decorative 

internal flooring products. These products are fast curing and available 

in a variety of colours, and are typically used for the refurbishment and 

protection of commercial and domestic floors. 

NEWTON 701 HB (LM 701) 

High Build Epoxy Floor Coating 

Newton 701 HB is a two-component solvent free water based epoxy 

resin based floor coating developed to provide protective and decorative 

properties to concrete, steel and other substrates. The material is 

supplied as a two-pack system comprising pre-weighed amounts of base 

and curing agent. After mixing together, an easily applied chemical and 

abrasion resistant finish is produced. This acts as a waterproof, tough, 

chemical resistant floor coating or as an internal lining for concrete or 

steel storage tanks containing oils, chemicals, water, etc. It is particularly 

suitable for chemical bunds. 


• Food preparation areas • Breweries 

• Industrial units • Warehouses 

• Garages 

• Below ground structures where Newton drainage conduits are utilised 

NEWTON 702 ECOSEAL (LM 702) 

Highly Resistant Polyurethane Floor Coating 

Newton 702 EcoSeal is a two component, solvent free, high performance 

Aliphatic Polyurethane resin which provides a hard yet flexible floor 

coating, with very high abrasion and chemical resistance. It provides 

excellent surface protection to floorings exposed to high wear and traffic. 

Newton 702 EcoSeal is supplied as a transparent coating for use above 

coloured bases such as Newton 701 HB or it can be coloured on site with 

RAL colours through the addition of pigment pastes and used above a 

suitable Newton primer as the stand-alone floor finish. The total absence 

of solvents allows for application in unventilated indoor areas. Newton 

702 EcoSeal cures to a UV stable gloss finish. 


• Heavy traffic areas 

• Industrial factories, depots and warehouses 

• Indoor tennis courts and recreational areas 

• Hard wearing finish to other floor coatings 

• Indoor car parks 

Page 21 







Damp Proofing 

NEWTON SYSTEM 800 - DAMP PROOFING 


Newton System 800 is a range of BBA approved damp proof membranes 

and ancillaries which are quick and clean to install and offer a permanent 

solution for damp proofing walls. 

Newton 805 Newlath and Newton 803 Newtonite meshed membranes 

provide a firm key and impermeable barrier on any damp or deteriorating 

surface ready for plaster, render or dot & dab plasterboard. 

The un-meshed Newton 803 is used where insulation requirements 

dictate the use of a timber or steel frame ready for plasterboard. Quick, 

clean and proven to work, Newton damp proof membranes offer a 

permanent and cost effective damp proofing solution. 

NEWTON 805 NEWLATH (M9 & M10) 

5mm Meshed Damp Proofing Membrane 

Newton 805 Newlath (formerly Newlath 2000) is a BBA approved high 

density polypropylene membrane with a rot-proof polythene mesh 

heat-welded during the manufacturing process to the surface of one side. 

The meshed surface creates a mechanical key to allow the membrane to 

be plastered, rendered or to receive dot & dab plasterboard. Newlath can 

be applied internally as a means of dealing with all forms of dampness 

inherent in structures and externally to properties suffering from driving 

and penetrating moisture. 

With over two million metres of Newton 805 Newlath installed nationally, 

Newlath is a cost effective and permanent method of dealing with 

dampness. 

Typical Applications 

• Internally for dealing with rising damp, salts and contaminants within 

existing structures. 

• Externally for protection of brick and masonry structures from driving 

and penetrating moisture 

• Treating dampness in listed buildings as the system is deemed 

removable and reversible and is sympathetic to the building fabric. 

• Applied to timber frame properties which require a rendered finish. 

Newton 805 Newlath is available in rolls 1.5m x 10m - 

15m 2 (M9) and 2m x 20m - 40m 2 (M10) 

Page 22 







Damp Proofing 

NEWTON 803 (M19 & M20) 

Non-Meshed Damp Proofing Membrane 

Newton 803 is a non-meshed damp proofing membrane for use above the 

ground. It can be used as an alternative to Newton 803 Newtonite and 

805 Newlath where a meshed surface is not required as a surface for 

direct plastering or rendering. Newton 803 is typically used where the wall 

finish to the damp-proof membrane is timber battens, a dry-lining frame 

or block wall. 

Newton 803 is 0.5mm thick and has a pattern of raised 3mm studs. 

The studs face the wall and create air channels that allow for vapour 

equalisation to take place between the membrane and the wall. 

Newton 803 is available in roll sizes 2m x 20m - 40m 2 

(M20) and 1m x 10m - 10m 2 (M19) 

NEWTON 803 NEWTONITE (M16, M21, M22) 

3mm Meshed Damp Proofing Membrane 

BBA approved Newton 803 Newtonite provides a firm key and 

impermeable barrier on any damp or deteriorating surface where direct 

bonding is not possible. Even poor and random substrates can easily 

receive Newtonite. 

Newtonite presents a physical barrier between the old surface and the 

new internal finish. Unlike many systems it can be punctured when new 

wall fixings are required. Holes drilled through the material must however 

be well sealed with Newton Mastic to stop any dampness 

bridging between the existing and new surface. 

Newtonite 803 is available in roll sizes: 

1m x 10m - 10m 2 (M16), 1m x 20m - 20m 2 (M21) 

and 2m x 20m - 40m 2 (M22) 

NEWTON 801 FLEXPROOF-X1 (FP1) 

Wet-room Waterproofing 

Newton 801 FlexProof-X1 is a highly advanced single component liquid 


that is splash proof in minutes and capable of handling severe building 

movements and deformations. 

Newton 801 FlexProof-X1 has characteristics that allow it to be used 

without a primer, without mixing and in weather conditions that preclude 

the use of alternatives. When applied by trowel to wet-room walls, 801 

FlexProof-X1 provides a continuous highly flexible membrane which can 

be blinded with sand ready for the tiled finish. 

Newtonite 801 FlexProof-X1 is available in containers of 15kg & 26kg 

Page 23 







Damp Proofing 

The ancillaries below are used with the three damp-proofing membranes that are included within Newton System 

800. Newton 803 is a plain membrane used where a dry-lining frame or a block wall is to be used as the wall 

finish. 803 Newtonite and 805 Newlath are meshed membranes used where a surface key is required for direct 

plastering, rendering or dot and dabbing to the wall membrane. Please read the membrane product data sheets 

for more information. 

Membrane Fixing Plug Jointing Tape Sealing Drilled Hole Plaster Stop Repairs 

803 MultiPlug Newton Overtape Not Required Not required Newton Overtape 

803 Newtonite 800 Mesh or 

Newtonite Plug 

805 Newlath 800 Mesh or 

Newtonite Plug 

Newton Mesh Tape Newton 800 Mastic Newton 800 Profile Newton Mesh Tape 

Newton Mesh Tape Newton 800 Mastic Newton 800 Profile Newton Mesh Tape 

NEWTON 800 MESH PLUG (A16) 

Above ground the Newton 800 Mesh Plug can be used internally and 

externally to secure Newton meshed membranes: 805 Newlath and 

803 Newtonite. Once the hole is drilled it should be primed with Newton 

Mastic sealant to prevent dampness tracking back along the plug. 

Size (Width x Length) 7mm x 50mm 

Quantity Per Bag 250 

NEWTON MULTIPLUG (A1) 

Newton MultiPlug is used with Newton 803. Drill a 10mm hole through 

the 803 membrane and hammer home with a club hammer. The 

MultiPlug can take a 5mm dia screw to allow the fixing of battens and 

dry-lining frames and the Newton Helifix Wall Tie without breaching 

the membrane. MultiPlug Pins are sold separately. 



NEWTON 800 COB PLUG (A17) 

In above ground situations, the Newton Cob Plug is used with 803 

Newtonite and 805 Newlath membranes. It has an expanding stem which 

provides effective anchorage in a wide range of base materials. Larger 

sizes of Newton Cob Plug can be sourced on request. 



NEWTON 800 NEWTONITE PLUGS (A20) 

Above ground the Newtonite Plugs can be used internally to secure 

Newton 803 Newtonite and 805 Newlath membranes. Once the hole 

is drilled it should be primed with Newton Mastic sealant to prevent 

dampness tracking back along the plug. 



Page 24 







Damp Proofing 

NEWTON 800 MASTIC (A18) 

Newton Mastic is used with 805 Newlath and 803 Newtonite. It is used 

to prime the plug hole prior to the fixing plug being hammered home, 

which serves to stop any ‘bridge’ happening between the damp or stained 

surface and the new surface. Newton Mastic is also used for sealing 

around protrusions. 

Unit of Sale 

0.38 litre tube 

NEWTON MESH TAPE (A25) 

Newton Mesh Tape is used to joint 803 Newtonite and 805 Newlath 

membranes as well as for repairs to the membrane and for sealing 

around protrusions. The meshed surface gives a good key for renders 

and plasters. 

Size (Width x Length) 

Unit of sale 

100mm x 10m 

Single units 

NEWTON OVERTAPE (A8) 

Newton Overtape is used for the jointing of Newton 803 as well as for 

repairs to Newton 803 and to seal around protrusions to the membrane. 

Size (Width x Length) 

Unit of sale 

100mm x 20m 

Single units 

NEWTON 800 PROFILE (A19) 

Newton Profile can be used with 803 Newtonite and 805 Newlath. It 

serves as a plaster stop, guaranteeing that the plaster/render will stop 

short of the floor. 

Size 

Unit of Sale 

2m lengths 

Single units 

Page 25 







Liquid Primers & Sealers 

NEWTON SYSTEM 900 - LIQUID PRIMERS & SEALERS 


Newton’s high performance range of liquid applied products are used in 

conjunction with System 200 and 700 liquid membranes. They act as 

priming agents for a variety of substrates prior to the application of our 

specialist waterproofing and flooring membranes. 

NEWTON 901 HUMIDITY PRIMER (PS 901) 

Epoxy Primer Suitable for High Humidity Substrate 

Newton 901 Humidity Primer is a solvent free two part epoxy resin coating 

typically used as a primer for Newton high performance liquid applied or 

sprayed roofing and flooring products. 

Newton 901 Humidity Primer would be chosen as the primer coating 

where the substrate contains humidity levels in excess of 4%. 

Application 

Mix Part A - Epoxy Resin with Part B - Hardener thoroughly with an electric 

paddle mixer for 2 min until a milky uniform colour is achieved (pot life of 

approx 30 minutes) 

Application rate is 0.3 kg per m 2 dependent on the quality of the 

substrate. Newton 901 Humidity Primer is supplied in 5kg, 10kg and 

20kg components. 

NEWTON 902 (PS 902) 

Liquid Applied Radon, Gas & Vapour Barrier 

Newton 902 is a single component high performance elastomeric liquid 

rubber membrane specifically designed for providing a radon, gas and 

vapour barrier to vertical and horizontal surfaces. Newton 902 is a cost 

effective vapour barrier material which can easily be applied via a stiff 

brush, roller or airless sprayer to a variety of different substrates including 

concrete, mortar, brick, Insulated Concrete Formwork (ICF), ceramics, 

steel, zinc or aluminium. 

Pre-dampen porous substrates prior to the application of the first coat. 

Application 

Newton 902 can be used as a primer for other Newton liquid membranes 

when applied in one coat of 0.33kg per m 2 or as a gas, vapour and 

waterproofing membrane with two coats totalling 1kg per m 2 

Newton 902 is supplied in 5kg, 10kg and 20kg tubs. 

Page 26 







Liquid Primers & Sealers 

NEWTON 903 PU PRIMER (PS 903) 

Epoxy Primer for Nonporous Substrate 

Newton 903 PU Primer is used for priming non-absorbent substrates, 

prior to application of Newton high performance liquid applied roofing and 

flooring products. 

It should be chosen as the primer where the substrate is nonporous such 

as ceramic, steel, glass, marble, polished concrete etc. 

Newton 903 PU Primer can be applied with roller, brush or cloth to a ratio of 

0.1kg per m 2 

Newton 903 PU Primer is supplied in units 4kg, 9kg or 20kg 

NEWTON 904 HP ACCELERANT (PS 904) 

Humidity Primer Accelerant 

Newton 904 HP Accelerant is a clear accelerant additive for exclusive 

use with Newton 901 Humidity Primer. The addition of Newton 904 HP 

Accelerant to Newton 901 Humidity Primer results in the primer being 

cured in 1 to 2 hours (diminishing the risk of alteration by rain, wind, etc.) 

The accelerated curing is achieved without any loss in its properties or 

changes in the chemical structure of the primer. 

Newton 904 HP Accelerant is supplied in 1kg units and has been 

designed to be added to a 20kg unit of Newton 901 Humidity Primer. 

Add the 1kg unit of Newton 904 HP Accelerant to the 20kg unit of the 

901 Humidity Primer once both parts A and B have been already mixed. 

Totally mix and homogenise both products together. 

Note: After adding 904 HP Accelerant to the 901 Humidity Primer the pot 

life is shortened to only 20-30 minutes and the combined product cannot 

be reused. 

NEWTON 906 MOULD STOP (PS 906) 

Mould Steriliser & Killer 

Newton 906 Mould Stop can eradicate mould in four easy steps. It is 

simple to use and as well as killing dangerous mould it prevents regrowth 

and eliminates musty odours. 

Newton 906 Mould Stop is suitable for walls, ceilings, skirting boards, 

window reveals, uPVC window and door frames. 

906 Mould Stop kit contains: 1 litre of Mould Stop Steriliser and Killer 

Spray, 1 x safety glasses, 1 x pair of disposable gloves, 1 x sponge and 

2 x 100ml Mould Stop Paint Additive. 

Once mixed Newton 906 Mould Stop will treat between 10 and 15m 2 

Page 27 






NEWTON FLEXPROOF 


NEWTON FLEXPROOF 

Highly Advanced Single Component Liquid Waterproofing Material 

Newton FlexProof-X1 forms an elastomeric polymer membrane that is 

rainproof in minutes and capable of handling severe building movements 

and deformations. 

FlexProof-X1 has characteristics that allow it to be used without a primer, 

without mixing and in weather conditions that preclude the use of 

alternatives. 

FlexProof-X1 is a multi-use product and can be applied by trowel or 

squeegee to a variety of different surfaces such as concrete, screed and 

timber boards to provide a continuous highly flexible membrane that is 

resistant to water pressures of up to 2 bar (20m) over construction joints 

of up to 0.25mm. 

Key Benefits: 

• No mixing required - simply open the packaging and use. 

• Can be used in sub-zero temperatures and on slightly damp 

substrate. 

• No primer required - saving on primer and labour costs 

• Single coat application. 

• 100% waterproof, but allows vapour diffusion. 

• Very flexible - Resistant to movement and fissures in substrates. 

• Excellent adhesion to suitable substrates. 

• Resistant to temperature variations maintaining its characteristics 

between -40ºC & 90ºC. 

• Excellent resistance to the high alkalinity of concrete. 

NEWTON FLEXPROOF-X1 (FP1) 


For the waterproofing of construction joints in new-build concrete 

construction of basements. When applied by trowel or squeegee over 

construction joints in concrete, FlexProof-X1 provides a continuous highly 

flexible membrane that is resistant to water pressures of up to 2 bar 

(20m) over construction joints of up to 0.25mm. 

Suitable Substrate: 

• Construction and movement joints to basement structures built of 

concrete. 

• Retained walls built in concrete or concrete block. 

• Construction and movement joints to decks and flat roofs built of 

concrete or timber. 

• Wet rooms built of concrete, masonry or timber. 

Page 28 






NEWTON DIATHONITE 

Insulating Plaster 

NEWTON DIATHONITE 

Eco Thermal Plaster with Insulation and Acoustic Properties 

Newton Diathonite is a premixed plaster, fibre-reinforced with cork 

(granular 0-3 mm), clay powders and NHL 3.5 natural hydraulic lime. 

The resulting natural compound produces a plaster with unrivalled 

thermal and acoustic properties that is both hard wearing and flexible 

which is ideal for both internal and external applications. 

Diathonite, when applied either internally or externally, creates a 

seamless thermal barrier which eliminates any risk of cold bridging within 

the structure. To achieve very high thermal and acoustic performance, 

Newton Diathonite will need to be applied at a thickness that is similar to 

those of standard wall insulation. 

One of the big advantages of applying Newton Diathonite to existing 

properties is that the application can be split between internal and 

external application, whereas conventional insulation can only be added 

to the inside of the walls and so impacts greatly on the internal space. 

It is usual for the internally applied insulation to then have a covering, 

such as plasterboard, which further reduces habitable space. By splitting 

the application of Diathonite between the inside and outside of the wall, 

similar insulation characteristics can be achieved with just half the space 

loss of conventional insulation. 

Key Benefits 

• Superb insulation properties thanks to the air spaces created by 

natural cork particles included within the plaster 

• High vapour permeability 

• Resistant to fire: Class 1 

• Eco-friendly 

• Can be spray applied allowing for very fast application 

• Very flexible - large elevations can be plastered without cracking 

• Impressive acoustic characteristics - over twice the performance of 

conventional plasters or renders 

Typical Applications 

• As a high performance insulated plaster for both the inside and 

outside of external walls 

• As a sound insulating plaster for both external and internal walls 

Page 29 






NEWTON SUMP AND PUMP 

Pumping Product Range 



Newton have an extensive range of submersible pumps and pumping 

ancillaries. We supply the highest quality pumps available in each class, 

for the control of clean ground water, grey water, effluent or sewage. 

CLEAN/GROUND WATER PUMPS 

NEWTON NP150 (P1) 

Medium head and low to medium duty pump. The NP150 is an automatic 

pump, with integral vertical float switch and so is not suitable for use with 

our pump control panels. It can be used with Newton Power Converters of 

1200W or over to give continual pumping even when the power is out. 

The NP150 is supplied with a one way check valve and should be used 

with 50mm pressure rated discharge pipe. The pump is sold as pump 

only, or as a key component in our Newton Titan-2 packaged pump 

system. 

3 year manufacturers warranty. 

NEWTON CP250 (P31) 

The Newton CP250 is a low cost and high quality clean water pump ideally 

suited for the removal of ground water from basements and cellars. The 

unique vertical operation float switch ensures that the pumps operate 

within the pump footprint removing the possibility of the float snagging 

during operation and allowing the pumps to be used within smaller 

sumps. The vertical float switch is also very flexible, allowing the pump 

switching height to be adjusted both in height between the ‘on’ and ‘off’ 

positions, but also in height relative to the pump. 

The CP250 is supplied with a one way check valve and and should be 

used with 50mm pressure rated discharge pipe. 

The pump is sold as pump only, or as a key component in our Newton 

Titan-2 and Newton Titan-Pro packaged pump systems. 

1 year manufacturers warranty or 3 year Newton warranty with proven 

service history. 

Page 30 

















The CP400 is supplied with a one way check valve and should be used 

with 50mm or 63mm pressure rated discharge pipe. The pump is sold 

as pump only, or as a key component in our Newton Titan-2 and Newton 

Titan-Pro packaged pump systems. 



NEWTON NP400 (P2 & P3) 

Available in both manual (P3) and automatic (P2) versions, the NP400 is 

the most popular high performance submersible pump in our portfolio. 

The NP400 has a unique vertical float mechanism which can be adjusted 

to suit each individual pumping assignment. It can be used with Newton 

Power Converters of 1200W or over to give continual pumping even when 

the power is out. 

The NP400 is supplied with a one way check valve and should be used 

with 50mm or 63mm pressure rated discharge pipe. The pump is sold 

as pump only, or as a key component in our Newton Titan-2 and Newton 

Titan-Pro packaged pump systems. 


NP400PP (P13) & NP400LLPS (SP1) 

The Newton NP400PP is a high quality puddle pump able to pump water 

down to just 1mm. The NP400PP is a manual pump with no switching 

control - the pump will run continually when connected to a power supply. 

Switching of puddle pumps is problematic because by their nature they 

are dealing with low heights of water. This makes conventional switching 

difficult. 

The NP400LLPS is the switched version of the NP400PP Puddle Pump. 

The NP400LLPS has a small control panel and low level switching 

module added to the NP400PP Puddle Pump that will give accurate and 

safe switching on of the pump at water levels of just 10mm. The NP400 

LLPS will pump down to just 1mm of water depth. The NP400PP and 

NP400LLPS are supplied with a one way check valve and should be used 

with 50mm pressure rated discharge pipe. 


Page 31 

















The CP750 can be supplied with a choice of one way valves and should 

be used with 50mm or 63mm pressure rated discharge pipe. 

The pump is sold as pump only, or as a key component in our Newton 

Titan-Pro packaged pump system. 



NEWTON NP750 (P5 & P6) 

The Newton NP750 is a high performance pump available as an 

automatic pump (P5), or as a manual pump (P6) for use with the CP2 

Control Panel. It can be used with Newton Power Converters of 3000W to 

give continual pumping even when the power is out. 

For increased duty in a twin pump system, separate discharge lines 

should be used. The NP750 is sold as pump only, or as a key component 

in our Newton Titan-Pro packaged pump system and should be used with 

50mm or 63mm pressure rated discharge pipe. 


EFFLUENT PUMP (NOT SEWAGE) 

NEWTON NP400W (P4) 

The Newton NP400W is a medium head and medium performance pump 

specifically placed within the Newton pumping range for when dishwasher, 

washing machine or bath/shower waste is to be removed from the 

sump. It is an automatic pump with a specially designed adjustable float 

arrangement that cannot be fouled by hardened soaps etc. It can be 

used with Newton Power Converters of 1200W or over to give continual 

pumping even when the power is out. 

The NP400W is sold as pump only, or as a key component in our Newton 

Titan-Pro packaged pump system and should be used with 50mm and 

63mm pressure rated discharge pipe. 


Page 32 








SEWAGE PUMPS 

NEWTON SP750 RANGER (P9) 

The Newton SP750 Ranger is a low head and high performance sewage 

pump for the removal of sewage, effluent, waste water and ground water 

with suspended soft solids of up to 50mm. 

The Newton SP750 Ranger is primarily used as the standard pump in our 

Trojan sump systems but can also be used as a stand-alone pump within 

formed concrete sumps and should be used with 63mm pressure rated 

discharge pipe. 


NEWTON FLYGT DXG (GRINDER) (P14 & P16) 

The Newton Flygt DXG (Grinder) is a high performance submersible 

grinder pump which cuts solids in sewage into smaller bits that can easily 

pass through the impeller and discharge pipes. 

The Newton Flygt DXG is primarily used as the standard pump in our 

Trojan sump systems but can also be used as a stand-alone pump within 

formed concrete sumps and should be used with 50mm pressure rated 

discharge pipe. 


Available in Automatic (P14) or Manual (P16) versions. 

SEWAGE LIFTING STATION 

TROJAN SEWAGE PUMPING SYSTEM (TR1-TR12) 

Newton Trojan systems are specialist packed sewage systems based upon 

a 610mm diameter sump with depth options of 1000mm and 1500mm. 

The Trojan systems are supplied as either single or twin pump systems 

using the Newton 750 Trojan (Vortex) or Newton Flygt DXG (Grinder). 

A hole cutter and 1 x 110mm wall flange is supplied allowing for accurate 

on-site positioning of the invert connection. 

Note: The Trojan System is not supplied with a High Water Level Alarm - 

Alarm and pump control options are available at extra cost. 

Page 33 








CLEAN/GROUND/EFFLUENT PUMPING SYSTEMS 

TITAN-PRO WHITE (TPW) 

The Newton Titan-Pro White is designed specifically to be used with 

Newton System 500. The adjustable neck allows for the sump to be 

installed at a fixed height relative to the slab so that the connection in 

from the Newton drainage system and the pump discharge line are made 

above the concrete. 

The sump can be used with single pumps, twin pumps and twin pumps 

with twin discharge lines for greater pump efficiency. 

The Titan-Pro White is available with the following pumps: CP250, CP400, 

NP400, NP400W, CP750, NP750. 

The system comprises a sump chamber with 450mm x 450mm recessed 

lid, single or double pumps, internal pipework, one-way valves and the 

Newton PA50 High Water Alarm. 

Chamber dimensions: 805mm high x 650mm wide 

TITAN-PRO GREEN (TPG) 

The Titan-Pro Green is designed for the pumping of ground water or 

surface water where the added features of the Titan-Pro White are not 

required. Ideally suited for receiving connections from rainwater gullies. 

A hole cutter and 1 x 110mm wall flange is supplied allowing for accurate 

on-site positioning of the invert connection. 

The sump can be used with single pumps or twin pumps with a single 

discharge line. 

The Titan-Pro White is available with the following pumps: CP250, CP400, 

NP400, NP400W, CP750, NP750. 


lid, single or double pumps, internal pipework, one-way valves and the 

Newton PA50 High Water Alarm. 


NEWTON TITAN-2 (T1-T10) 

The Titan-2 pumping system is designed for when a smaller chamber than 

the Titan-Pro is required and is suitable for low volume pumping situations 

within basements or for the pumping of collected surface water from lightwells 

etc. 

The Titan-2 is available with the following pumps: NP150, CP250, CP400, 

NP400, NP400W. 


lid, single or double pumps, internal pipework, one-way and shut-off 

valves and the Newton PA50 High Water Alarm. 


Page 34 








PUMPING ANCILLARY PRODUCTS 

NEWTON CONTROL PANEL-PRO (CP2) 

The Newton Control Panel Pro is a class-leading pump control panel with 

many unique features which has been designed by Newtons to provide 

the ultimate in pump operation and diagnostic capabilities. The panel 

interfaces with Newton Power Converters and telemetry systems and can 

be connected to the house monitoring system. 

The Control Panel PCB is split with two separate circuits, ensuring that 

pumping will continue even if one of the control circuits should fail. This 

effectively means that Newton Control Panel Pro is two control panels in 

one case, offering unrivalled protection. 

NEWTON HIGH WATER LEVEL ALARM (PA50) 

The Newton High Level Water Alarm–PA50 has been designed to detect 

high water levels within pump sump chambers and is included within the 

Newton Titan-Pro and Newton Titan-2 pumping systems. The alarm is 

battery operated and uses a standard 9V PP3 battery. 

The alarm can be programmed to automatic reset or manual reset after 

an alarm occurrence. A mute button to the front face silences the alarm 

once the alarm condition is discovered. A flashing alarm light gives visual 

indication of an alarm condition and this light will continue to show even 

when the alarm sounder is muted. 

NEWTON DIALER (PA5, PA6, PA7) 

The Newton Dialer – PA5 provides enhanced alarm capability to the 

Newton PA50 High Water Level Alarm fitted as part of a Newton Pumping 

System. The PA5 Dialer will contact up to 8 persons by text or speech (or 

both simultaneously) via the standard BT Telephone line to warn of an 

alarm condition with the PA50 Alarm. The Dialer is supplied with a multicore 

cable that provides signal connections from the PA50 Alarm. 

A 12V power supply is required and this should be ordered with the Dialer 

at purchase depending on whether the PA50 Alarm is used with a system 

that contains a Newton Power Converter: 

If no Newton Power Converter is included within the pumping system, the 

Mains Connector For Dialer is required – Newton Code PA7. 

If the pumping system includes a Newton Power Converter, the Battery 

Connection For Dialer is required – Newton Code PA6. 

Page 35 








PUMPING ANCILLARY PRODUCTS 

NEWTON 1200w POWER CONVERTER (C1 & C3) 

Battery back up facilities for pumps of 150W and 400W is provided by the 

Newton 1200W Power Converter - C1. The unit receives 12V power from 

a deep cycle leisure battery and converts this into 230V mains power to 

ensure that the Newton Pump continues to operate even during a power 

outage. A two phase charger ensures that the battery is fully charged at all 

times by trickle charging to keep the battery at optimal charge and then by 

boosting up to 20 Amps to quickly re-charge the battery after extended use. 

Purchase Code C1 is for the Power Converter only. Purchase code C3 

includes a 115A/H deep cycle leisure battery, a secure battery box, and the 

power leads for connection to the mains and the battery. 

Additional batteries and link leads can be purchased to increase the volume 

of water that can be pumped during a power failure. 

NEWTON 3000w POWER CONVERTER (C2 & C4) 

The Newton 3000w Power Converter - C2 receives 12V power from a deep 

cycle leisure battery and converts this into 230V mains power to ensure 

that the Newton Pump continues to operate even during a power outage. 

A two phase charger ensures that the battery is fully charged at all times 

by trickle charging to keep the battery at optimal charge, and then by 

boosting up to 20 Amps to quickly re-charge the battery after extended 

use. This 3000W unit is designed to be used with single Newton pumps 

with power outputs of up to 750W only or with dual pumps of 400W to 

750W when switched by one of our Control Panels. 

Purchase Code C2 is for the Power Converter only. Purchase code C4 

includes a 115A/H deep cycle leisure battery, a secure battery box, and 

the power leads for connection to the mains and the battery. 

Additional batteries and link leads can be purchased to increase the volume 

of water that can be pumped during a power failure. 

Page 36 






NEWTON MULTI-USE 

Multi-Use Products 



The Multi-Use section is home to products that are used within more 

than one of our systems. WaterSeal Tape, for example, can be used with 

System 200, System 400, System 500, System 600 and System 800. 

Highlights include Newton Mesh Tape, which is used with all of our 

meshed membranes to facilitate direct plastering or rendering, and the 

Newton MultiPlug which includes a soft rubber sealing grommet and a 

pin, which when inserted into the plug, expands the fixing to provide a 

better fit within soft or friable substrate. 

NEWTON MESH TAPE (A25) 

Newton Mesh Tape is a self-adhesive sealing tape made of a butyl 

rubber compound with a polypropylene fleece finish. The tape has been 

developed for use with Newton Meshed Membranes where a surface ‘key’ 

is required for plastering or rendering over. 

Newton Mesh Tape is the recommended jointing tape for the following 

Newton membranes: Newton 603 Mesh, Newton 803 Newtonite, Newton 

805 Newlath. It can also be used as an overtape to provide a key above 

joints to Newton System 500 meshed waterproofing membranes (Newton 

503 Mesh and Newton 508 Mesh), over joints already sealed with Newton 

WaterSeal Tape, Newton WaterSeal Rope or Newton Overtape. 

Newton Mesh Tape is available in 150mm x 10m rolls. 

NEWTON OVERTAPE (A7, A8, A9) 

Newton Overtape is used to create single sided taped joints as an 

overtape to seal adjacent butted and overlapped membranes, or to seal 

above joins to the membrane created whilst shaping the membrane to fit 

convoluted substrate. Newton Overtape can also be used for the sealing 

of protrusions through the membrane. 

Newton Overtape is available in rolls 150mm x 20m (A7-Black), 

100mm x 20m (A8-Black, A9-White) 

NEWTON WATERSEAL ROPE (A6, A6W) 

Newton WaterSeal Rope is used to form a seal at the overlap of adjacent 

sheets of Newton membranes when neither a flange joint or stud into stud 

joint has been made. A bead of WaterSeal Rope is used for the sealing 

of penetrations through the Newton membranes. WaterSeal Rope is also 

used to create a sealing ring to the base of the Newton NuSeal Plug. 

WaterSeal Rope is supplied in rolls 10mm x 4.75m and is available in 

Black (A6) or White (A6W) 

Page 37 







Multi-Use Products 

NEWTON WATERSEAL TAPE (A5, A5W) 

Newton WaterSeal Tape is used to form a seal at the overlap of adjacent 

sheets of Newton membranes. 

WaterSeal tape is placed between the flange of one sheet and the top 

flat surface of the next, or if the studs interlock, it can be used to seal 

between the flat contact area of this type of joint. 

WaterSeal tape is supplied in rolls 30mm x 2mm x 22.5m in Black (A5) 

and White (A5W) 

NEWTON MULTIPLUG (A1) 

Newton MultiPlug has been engineered to give a better fix in questionable 

substrates. It has the added benefit of having a rubber sealing grommet 

supplied with the plug. In very poor substrate, a pin (supplied in bags 

of 100 at extra cost) is inserted into the plug that expands its outer 

circumference by nearly 2mm to tighten the plug into the substrate. 

The Newton MultiPlug is pre-drilled to accept a size 10 (5mm) 

self-tapping screw for the fixing of battens or other dry-lining systems. 

Newton MultiPlugs are recommended in all below ground membrane 

applications except vaulted arches. 

Note: 10mm SDS drill bit required, plugs are 57mm in length. 

Newton MultiPlugs are supplied in bags of 100 (A1) 

NEWTON NUSEAL PLUGS (A2, A3) 

Newton NuSeal Plugs are used to secure Newton System 500 membranes 

to building substrate and to fix battens or tracking systems. Prior to using 

NuSeal plugs, wrap a bead of Newton WaterSeal Rope around the head of 

the plug to form a compression seal. 

NuSeal Plugs are recommended when applying Newton 508 or Newton 

508 Mesh to vaulted arches. 

Note: 11mm SDS drill bit required, plugs are 70mm in length. 

Newton NuSeal Plugs are supplied in bags of 100 in Red (A2) or 

White (A3) 

Page 38 





Damp Proofing and 

Structural Waterproofing Solutions 

Basement Waterproofing to BS8102 - Existing Basements 

Newton’s market leading basement waterproofing solution Newton System 

500 is ideal for waterproofing existing basements and cellars. It is commonly 

used where conventional ‘tanking’ has failed, and it fully conforms with the 

recommendations within BS8102:2009 Code of Practice for the Protection of 

Below Ground Structures Against Water from the Ground. 

BS8102:2009 recommends that the waterproofing solution is fully 

maintainable and serviceable. Newton System 500 is a cavity drain 

membrane system which works by placing designed and maintainable 

depressurisation voids at known weaknesses in the structure, so that 

problem water is simply captured and diverted out of the property. 

Newton System 500 is ideal for application to listed and historic buildings 

as it is deemed ‘reversible’ - a requirement of conservation authorities. 

Newton System 500 has been installed 

in the Grade I Listed Royal Courts of 

Justice, London 

Basement Waterproofing to BS8102 - New Build Basements 

Newton Waterproofing Systems provide the designer with solutions for all 

aspects of the waterproofing of the structure, from the water bars within 

the construction joints to the sealing of the deck above. Systems can be 

used in isolation or can be combined as recommended by BS8102:2009 

to give greater assurance of waterproofing performance. BS8102:2009 

defines three types of waterproofing and Newton Systems are available for 

all three types and combinations of all three types: 

Type A - (barrier) protection: Newton System 100, Newton System 200, 

Newton System 400 

Type B - (structurally integral) protection: Newton System 300 

Type C - (drained) protection: Newton System 500, Newton System 400 

Combination system can be provided for Type A + Type B, Type A + Type C 

and Type B + Type C 

Newton offer complete waterproofing 

solutions for new build basements 

Damp Proofing Listed Buildings 

When dealing with listed and historic buildings, it is fundamentally 

important to maintain the structural and aesthetic integrity of the 

building. Newton damp proof membranes can be sympathetically applied 

with little or no preparation required. The damp proof membrane provides 

an impervious separation barrier between the damp surface and the new 

internal wall, so moisture is prevented from affecting the internal finishes. 

Newton wateproofing systems have been used in many listed and historic 

buildings including: the British Museum, the Houses of Parliament, Windsor 

Castle, St Georges Hall - Liverpool, the Royal York Hotel - Bath, Wallis House 

- Middlesex, Limerick Court House - Ireland and Menin Gate - Ypres. 

John Newton & Company were the original innovators in damp proofing, 

having introduced a damp proof membrane in 1937. Our leading damp 

proof membrane, Newton 805 Newlath, remains the original meshed 

membrane, and over two million metres have been installed in the 

UK alone. 

Newton 805 Newlath has been used to 

damp proof walls in Windsor Castle 

Page 39 





Damp Proofing and 

Structural Waterproofing Solutions 

Waterproofing Concrete Structures 

Newton FlexProof is a multi-faceted single component flexible 

waterproofing system which can be applied to reinforced concrete in a 

one-coat application without the need for primers. It outperforms its rivals 

by having the capacity to be installed in temperatures below 5º C. 

FlexProof can be used to waterproof podium decks and balconies, 

construction/movement joints, retaining walls and wet rooms. It is 

capable of handling severe building movements and deformations. 

FlexProof contains no solvents and as such can be applied internally as 

well as externally. 

Upgrading the Thermal Performance of Buildings 

Newton Diathonite Insulation Plaster has a high thermal capacity due to 

the presence of cork. It is made from natural components and hydraulic 

lime. In addition, Diathonite offers soundproofing benefits and its 

application to structures eliminates cold bridging and provides a robust 

and high quality finish. 

Diathonite applied externally can upgrade the building’s thermal 

performance to meet building regulation standards thus negating the 

need to insulate internally, saving time and space. 

The application of Diathonite Insulation Plaster to a building also 

saves on energy costs, keeping the structure cool in summer and warm 

in winter. 

Newton FlexProof is rainproof in minutes 

and can be applied in sub-zero temperatures 

Newton Diathonite Insulation Plaster is 

an eco thermal plaster with excellent 

insulation and acoustic properties 

Newton Registered Installers 

Newton Specialist Basement Contractors (NSBC) are a nationwide group 

of professional waterproofing and damp proofing contractors who provide 

the best quality products, design and installation available in all aspects 

of basement waterproofing and damp proofing. 

NSBCs can offer peace of mind to the designer and the client by taking full 

design liability on the project, and in addition they must be able to offer “PI” 

(Professional Indemnity) on waterproofing design and offer independent 

insured guarantees for the installation. They are regularly trained and 

assessed by John Newton & Company, and adhere to very strict criteria. The 

requirements of BS8102:2009 Code of Practice for the Protection of Below 

Ground Structures Against Water from the Ground asks for a waterproofing 

specialist to be included as an integral part of the design team to ensure 

that an integrated waterproofing solution is realised. 

For a list of Newton Specialist Basement Contractors in your area, please 

contact John Newton & Company. 

Newton Specialist Basement Contractors 

offer guaranteed waterproofing solutions 

For many more case studies, please see www.newton-membranes.co.uk. 

For further information, free technical advice or additional copies of this catalogue 

please ring 020 7237 1217 or e-mail info@newton-membranes.co.uk 

Page 40 





Protecting buildings, since 1848 

NEWTON WATERPROOFING SYSTEMS 

Innovators In Structural Waterproofing 

And Damp Proofing Products For Over 160 Years 

John Newton & Co Ltd, Est 1848, is the UK’s leading independent supplier of structural 

waterproofing systems, water control and drainage products. Newtons offer the best 

available, BBA certificated solutions for waterproofing and damp proofing applications 

in new-build and refurbishment projects. Our range of structural waterproofing 

systems, including cementitious products, deck and roofing membranes and liquid 

applied floor coatings enable us to offer full waterproofing solutions for a wide variety 

of projects. 

Newton Waterproofing Systems control and remove unwanted water from leaking 

tunnels and underpasses, railway arches, wet basements, flooded cellars and 

damp vaults to make warm habitable areas or areas suitable for dry storage in both 

commercial and domestic projects. Newton’s portfolio of concrete waterproofing 

products gives specifiers the tools to provide full building envelope protection to 

reinforced concrete structures. 

Newton structural waterproofing and damp proofing products offer the highest 

level of protection. Our team of technical experts can design and modify technical 

drawings in all formats and design a waterproofing solution best suited to your 

requirements. 

Newton Specialist Basement Contractors (NSBC) can offer a fully guaranteed design 

and installation of our systems and “PI” (Professional Indemnity) on waterproofing 

design and offer independent insured guarantees for the installation. Please contact 

us for a list of NSBCs in your area. 

John Newton & Company Ltd. 

12 Verney Road, London SE16 3DH 

Phone: 020 7237 1217 

www.newton-membranes.co.uk info@newton-membranes.co.uk

Newton Waterproofing Systems Brochure - Barbour Product Search

Create successful ePaper yourself

Delete template?

Save as template?