sivacon
sivacon sivacon
SIVACON Adapts to Your Requirements Modular technology in every single cubicle and in the design of the overall system allows the SIVACON switchboard system to adapt to all requirements. • Busbars can optionally be located at the top or rear • Any components can be installed in the device compartments regardless of the busbar position and cubicle depth • Requirement-oriented subdivision of function compartments from Form 1 to Form 4 (VDE 0660 Part 500) • Withdrawable and fixedmounted units can be combined in one cubicle Optimum adaptation to space conditions • When installed, all switchboard cubicles are flush at the front and rear • Cables and bars can optionally be connected from above or below • Busbars can be installed easily in constricted space on site Swift adaptation to new performance demands • Easy replacement or addition of function units • Good busbar accessibility allows simple replacement • Modular technology enables simple subsequent ordering and short delivery times 400 400 400 600 400 400 600 4 Device compartment Cross-wiring compartment Busbar compartment Cable connection compartment optionally at the side, top or bottom
SIVACON for All Applications in the Low-Voltage Network Power Center I n up to 6300 A I cw up to 100 kA I pk up to 220 kA Main distribution board I n up to 4000 A I cw up to 100 kA I pk up to 250 kA Motor Control Center I n up to 2500 A I cw up to 50 kA I pk up to 110 kA Subdistribution board I n up to 2500 A Icw up to 50 kA I pk up to 110 kA Loads M M M M M M M 5
- Page 1 and 2: The Variable Low-Voltage Switchboar
- Page 3: Fig. 1 Power Center, Main distribut
- Page 7 and 8: Every circuit-breaker is assigned a
- Page 9 and 10: Plug-on bar system, protected again
- Page 11 and 12: Size 1 withdrawable unit, 30 kW, wi
- Page 13 and 14: All power and control cables are co
- Page 15 and 16: Diverse connection possibilities Fu
- Page 17 and 18: Capacitor and controller modules fo
- Page 19 and 20: Plug-on bus system Lateral guide ra
- Page 21 and 22: SIVACON is capable of communication
- Page 23 and 24: Part-integrating solid wall design
- Page 25 and 26: SIVACON is resistant to internal ar
- Page 27 and 28: Technical Data at a Glance Standard
SIVACON Adapts to Your<br />
Requirements<br />
Modular technology in every single cubicle and<br />
in the design of the overall system allows the<br />
SIVACON switchboard system to adapt to all<br />
requirements.<br />
• Busbars can optionally be<br />
located at the top or rear<br />
• Any components can be<br />
installed in the device<br />
compartments regardless<br />
of the busbar position and<br />
cubicle depth<br />
• Requirement-oriented<br />
subdivision of function<br />
compartments from<br />
Form 1 to Form 4<br />
(VDE 0660 Part 500)<br />
• Withdrawable and fixedmounted<br />
units can be<br />
combined in one cubicle<br />
Optimum adaptation to<br />
space conditions<br />
• When installed, all<br />
switchboard cubicles are<br />
flush at the front and rear<br />
• Cables and bars can<br />
optionally be connected<br />
from above or below<br />
• Busbars can be installed<br />
easily in constricted space<br />
on site<br />
Swift adaptation<br />
to new performance<br />
demands<br />
• Easy replacement or addition<br />
of function units<br />
• Good busbar accessibility<br />
allows simple replacement<br />
• Modular technology enables<br />
simple subsequent ordering<br />
and short delivery times<br />
400 400 400<br />
600 400<br />
400 600<br />
4<br />
Device compartment<br />
Cross-wiring compartment<br />
Busbar compartment<br />
Cable connection compartment<br />
optionally at the side, top or bottom