Catalyst 6500 Series Switches Installation Guide - Ipland

More documents

Recommendations

Info

Site Requirements Chapter 2 Preparing for Installation If you are installing your Catalyst 6500 series switch in an enclosed or partially enclosed rack, we strongly recommend that you verify that your site meets the following guidelines: • Verify that there is a minimum of 6 inches (15 cm) of clearance between the sides of the rack and both the chassis air intake grill and the chassis air exhaust grill. • Verify that the ambient air temperature within the enclosed or partially enclosed rack is within the chassis operating temperature limits. After installing the chassis in the rack, power up the chassis and allow the chassis temperature to stabilize (approximately 2 hours). Measure the ambient air temperature at the chassis air intake grill and at the chassis air exhaust grill by positioning an external temperature probe approximately 1 inch (2.5 cm) away from the grills, in line with the chassis slot occupied by the supervisor engine. – If the ambient intake air temperature is less than 104°F (40°C), the rack meets the intake air temperature criterion. – If the ambient intake air temperature exceeds 104°F (40°C), the system might experience minor temperature alarms and is in danger of overheating. – If the ambient intake air temperature equals or is greater than 131°F (55°C), the system will experience a major temperature alarm and shut down. • Verify that the enclosed or partially enclosed rack allows an adequate flow of air through the switch chassis as follows: – If the difference between the measured intake air temperature and the exhaust air temperature does not exceed 10°C, there is sufficient airflow in the rack. – If the difference in air temperature exceeds 10°C, there is insufficient airflow to cool the chassis. Note The 10°C temperature differential between the intake and the exhaust must be determined by taking measurements using external digital temperature probes. Do not use the chassis internal temperature sensors to measure the temperature differential. • Plan ahead. Your Catalyst 6500 series switches currently installed in an enclosed or partially enclosed rack might meet ambient air temperature and air flow requirements now. However, if you add more chassis to the rack or you add more modules to a chassis in the rack, the additional heat generated might cause the ambient air temperature within the rack to exceed 104°F (40°C) and can cause minor alarms. Selecting the Proper Rack-Enclosure or Cabinet Cisco Systems has identified two rack-enclosures that are determined to be Cisco-compatible: Panduit Corporation—The Net-Access Cabinet (p/n CN4-1) is determined to be Cisco-compatible for the Catalyst 6500 series product line. Contact Panduit Corporation for further information on this rack enclosure. Their corporate website is http://www.panduit.com. Their Customer Service and Technical Support phone number is 800 777-3300. Chatsworth Products, Inc.—The N-Series TeraFrame Network Cabinet (p/n NF2K-113C-C42) is determined to be Cisco-compatible for the Catalyst 6500 series product line. Contact Chatsworth Products, Inc. for further information on this rack enclosure. Their corporate website is http://www.chatsworth.com. Their Customer Service and Technical Support phone number is 800 834-4969 (Monday to Friday, 5 a.m. to 5 p.m., (0500 to 1700) Pacific Time). 2-4 Catalyst 6500 Series Switches Installation Guide OL-5781-08
Chapter 2 Preparing for Installation Site Requirements Chassis Fan Trays The chassis fan assembly provides cooling air for the supervisor engine and the switching modules. Table 2-1 lists the Catalyst 6500 series switch chassis along with the supported and unsupported fan trays. Table 2-2 lists the chassis air flow architecture and requirements for the Catalyst 6500 series switches. If an individual fan within the assembly fails, the FAN STATUS LED turns red. Individual fans within a fan tray assembly cannot be replaced; you must replace the entire fan tray assembly. To replace a fan tray assembly, see the “Removing and Installing the Fan Tray” section on page 4-82. Refer to your software configuration guide for information on environmental monitoring. Table 2-1 Catalyst 6500 Series Chassis Fan Tray Support Chassis Model Supported Fan Trays Unsupported Fan Trays Catalyst 6503 FAN-MOD-3 WS-C6503-E-FAN FAN-MOD-3HS (high speed) Catalyst 6503-E WS-C6503-E-FAN FAN-MOD-3 FAN-MOD-3HS (high speed) Catalyst 6504-E FAN-MOD-4HS (high speed) — Catalyst 6506 WS-C6K-6SLOT-FAN WS-6506-E-FAN WS-C6K-6SLOT-FAN2 (high speed) Catalyst 6506-E WS-6506-E-FAN (high speed) WS-C6K-6SLOT-FAN Catalyst 6509 WS-C6K-9SLOT-FAN WS-C6K-6SLOT-FAN2 (high speed) WS-6509-E-FAN WS-C6K-9SLOT-FAN2 (high speed) Catalyst 6509-E WS-6509-E-FAN (high speed) WS-C6K-9SLOT-FAN Catalyst 6509-NEB WS-C6509-NEB-FAN WS-C6K-9SLOT-FAN2 (high speed) — WS-6509-NEB-UPGRD 1 (high speed) Catalyst 6509-NEB-A FAN-MOD-09 (high speed) — Catalyst 6509-V-E WS-C6509-V-E-FAN (high — speed) Catalyst 6513 WS-C6K-13SLOT-FAN WS-C6513-E-FAN WS-C6K-13SLT-FAN2 (high speed) Catalyst 6513-E WS-C6513-E-FAN WS-C6K-13SLOT-FAN WS-C6K-13SLT-FAN2 1. Optional high-speed fan tray is part of the WS-6509-NEB-UPGRD kit. For systems operating with DC-input power supplies, all you need is the upgrade kit. For systems operating with AC-input power supplies, you need the upgrade kit plus WS-CAC-3000W (3000 W power supply) or better to operate the fan tray. OL-5781-08 Catalyst 6500 Series Switches Installation Guide 2-5
Page 1 and 2:
Catalyst 6500 Series Switches Insta
Page 3:
NOTWITHSTANDING ANY OTHER WARRANTY
Page 6 and 7:
Contents Power Source Interruptions
Page 8 and 9:
Contents Attaching the Interface Ca
Page 10 and 11:
Contents 100-MB Transceivers B-1 1-
Page 12 and 13:
Conventions Preface Chapter Title D
Page 14 and 15:
Conventions Preface Warnings use th
Page 16 and 17:
Conventions Preface Varning! VIKTIG
Page 18 and 19:
Conventions Preface xviii Catalyst
Page 20 and 21:
Related Documentation Preface Obtai
Page 22 and 23:
WS-SUP32-GE-3B Catalyst 6503 Switch
Page 24 and 25:
Catalyst 6503 Switch Chapter 1 Prod
Page 26 and 27:
Page 28 and 29:
WS-SUP32-GE-3B Catalyst 6503-E Swit
Page 30 and 31:
Catalyst 6503-E Switch Chapter 1 Pr
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
WS-X6408 8 PORT GIGABIT ETHERNET WS
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49: Catalyst 6506-E Switch Chapter 1 Pr
Page 50 and 51: WS-X6408 WS-X6408 WS-X6408 WS-X6408
Page 52 and 53: Catalyst 6509 Switch Chapter 1 Prod
Page 56 and 57: WS-X6408 WS-X6408 WS-X6408 WS-X6408
Page 62 and 63: FAN STATUS LINK LINK LINK LINK LINK
Page 64 and 65: Catalyst 6509-NEB Switch Chapter 1
Page 70 and 71: Catalyst 6509-NEB-A Switch Chapter
Page 76 and 77: Catalyst 6509-V-E Switch Chapter 1
Page 88 and 89: WS-X6408 8 PORT GIGABIT ETHERNET WS
Page 96 and 97: Safety Chapter 2 Preparing for Inst
Page 100 and 101: WS-X6K-SUP2-2GE OSM-4OC12 POS-SI 4
Page 102 and 103: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
Page 104 and 105: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
Page 106 and 107: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 110 and 111: Site Requirements Chapter 2 Prepari
Page 116 and 117: Power Requirements Chapter 2 Prepar
Page 118 and 119: Cabling Requirements Chapter 2 Prep
Page 120 and 121: Site Preparation Checklist Chapter
Page 122 and 123: Chapter 3 Installing the Switch The
Page 124 and 125: Rack-Mounting Guidelines Chapter 3
Page 126 and 127: Chassis Installation Kits and Cable
Page 128 and 129: Installing a Catalyst 6503 or Catal
Page 130 and 131: CAUTION STATUS LINK CONSOLE LINK LI
Page 132 and 133: Installing a Catalyst 6504-E Switch
Page 134 and 135: WS-SUP32-GE-3B CAUTION STATUS LINK
Page 136 and 137: Installing a Catalyst 6504-E Switch
Page 142 and 143: WS-X6408 WS-X6408 WS-X6224 24 PORT
Page 144 and 145: WS-X6408 WS-X6408 WS-X6224 24 PORT
Page 146 and 147: Installing a Catalyst 6509-NEB or C
Page 148 and 149:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 150 and 151:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 152 and 153:
WS-C6500-SFM SWITCH FABRIC MDL WS-C
Page 154 and 155:
Page 156 and 157:
Installing a Catalyst 6509-V-E Swit
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Installing a Catalyst 6513 or Catal
Page 164 and 165:
Page 166 and 167:
WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
Page 168 and 169:
Generic Installation Procedures Cha
Page 170 and 171:
Generic Installation Procedures Cha
Page 172 and 173:
Establishing the System Ground Chap
Page 174 and 175:
OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
Page 176 and 177:
Page 178 and 179:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 180 and 181:
Establishing the System Ground Chap
Page 182 and 183:
Attaching the Interface Cables Chap
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
LINK Attaching the Interface Cables
Page 194 and 195:
LINK Attaching the Interface Cables
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Verifying Switch Chassis Installati
Page 206 and 207:
Verifying Switch Chassis Installati
Page 208 and 209:
Removing and Installing the AC-Inpu
Page 210 and 211:
OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
Page 212 and 213:
Page 214 and 215:
ALL FASTENERS MUST BE FULLY ENGAGED
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
OSM-4OC12 POS-SI 1 2 1 2 1 1 2 2 3
Page 224 and 225:
Removing and Installing the DC-Inpu
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
CISCO SYSTEMS, INC Removing and Ins
Page 268 and 269:
CISCO SYSTEMS, INC 1 2 3 4 INPUT OK
Page 270 and 271:
Page 272 and 273:
CISCO SYSTEMS, INC Removing and Ins
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
CISCO SYSTEMS, INC 1 2 3 4 INPUT OK
Page 282 and 283:
Removing and Installing PEMs Chapte
Page 284 and 285:
Removing and Installing PEMs Chapte
Page 286 and 287:
OSM-4OC12 POS-SI 1 2 1 2 1 1 2 2 3
Page 288 and 289:
Removing and Installing the Fan Tra
Page 290 and 291:
WS-X6K-SUP2-2GE OSM-4OC12 POS-SI OS
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Removing and Installing the Fan Tra
Page 300 and 301:
ACTIVE TX RX RX TX ACTIVE TX RX RX
Page 302 and 303:
Installing the Air Filter Assembly
Page 304 and 305:
Installing the Remote Power Cycling
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Power Supply Compatibility Matrix A
Page 312 and 313:
Power Supply Compatibility Matrix A
Page 314 and 315:
950 W AC-Input and DC-Input Power S
Page 316 and 317:
950 W AC-Input and DC-Input Power S
Page 318 and 319:
1000 W AC-Input Power Supply Append
Page 320 and 321:
Page 322 and 323:
1300 W AC-Input and DC-Input Power
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
AC Power Cord Illustrations Appendi
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Power Supply Redundancy Appendix A
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Pluggable Transceivers Appendix B T
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Module Connectors Appendix B Transc
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
Page 418 and 419:
Cables Appendix B Transceivers, Mod
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
Cleaning the Fiber-Optic Connectors
Page 426 and 427:
Cleaning the Fiber-Optic Connectors
Page 428 and 429:
Appendix C Repacking the Switch Fig
Page 430 and 431:
Appendix D Chassis and Module Power
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
Solving Problems at the System Comp
Page 448 and 449:
Troubleshooting the Power Supply Ap
Page 450 and 451:
Troubleshooting Modules Appendix E
Page 452 and 453:
Contacting Customer Service Appendi
Page 454 and 455:
Index 4000 W DC-input power supplie
Page 456 and 457:
Index power supplies description 1-
Page 458 and 459:
Index features table 1-69 form fact
Page 460 and 461:
Index Catalyst 6504-E switches 1-14
Page 462 and 463:
Index R DC power cable leads color
Page 464:
Index U startup E-2 supervisor engi
show all

Catalyst 6500 Series Switches Installation Guide - Ipland

Create successful ePaper yourself

Delete template?

Save as template?