Catalyst 6500 Series Switches Installation Guide - Ipland
Catalyst 6500 Series Switches Installation Guide - Ipland Catalyst 6500 Series Switches Installation Guide - Ipland
950 W AC-Input and DC-Input Power Supplies Appendix A Power Supply Specifications Figure A-3 DC Power Entry Module (PEM) Catalyst 6503 DC PEM Captive installation screws 79980 950 W Power Supply Specifications Table A-3 lists the specifications for the 950 W AC-input power supply. Table A-3 950 W AC-Input Power Supply Specifications Specification AC-input type Description Autoranging input with power factor correction (PFC) Note Power factor correction is a standard feature on all Catalyst 6500 series AC-input power supplies. PFC reduces the reactive component in the source AC current allowing higher power factors (typically 99 percent or better) and lower harmonic current components. AC-input voltage • Low-line (120 VAC nominal)—90 VAC (min) to 132 VAC (max) • High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max) AC-input current • 12 A @ 120 VAC AC-input frequency • 6 A @ 230 VAC 50/60 Hz (nominal) A-6 Catalyst 6500 Series Switches Installation Guide OL-5781-08
Appendix A Power Supply Specifications 950 W AC-Input and DC-Input Power Supplies Table A-3 950 W AC-Input Power Supply Specifications (continued) Specification Branch circuit requirement Power supply output capacity Description Each chassis power supply should have its own dedicated, fused-branch circuit: • For North America—15 A Power supply output • 15 A @ +1.5 VDC Output holdup time kVA rating 1 Heat dissipation Weight • For International—Circuits sized to local and national codes • All Catalyst 6500 series AC-input power supplies require single-phase source AC. • All AC power supply inputs are fully isolated. – Source AC can be out of phase between multiple power supplies in the same chassis, which means that PS1 can be operating from phase A and PS2 can be operating from phase B. – For high-line operation, the power supply operates with the hot conductor wired to a source AC phase and the neutral conductor wired either to ground or to another source AC phase as long as the net input voltage is in the range of 170 to 264 VAC. – Source AC can be out of phase between AC inputs on power supplies that are equipped with multiple AC inputs, which means that power cord 1 can be plugged into phase A and power cord 2 can be plugged into phase B. 950 W maximum (100–240 VAC) • 2.5 A @ +3.3 VDC • 19.15 A @ +50 VDC 20 ms minimum 1.32 kVA 4441 BTU/hour (approx.) 8.2 lb (3.7 kg) 1. The kVA rating listed for the power supply should be used as the sizing criteria for both UPS outputs as well as standard circuits and transformers to power a switch. OL-5781-08 Catalyst 6500 Series Switches Installation Guide A-7
- Page 264 and 265: Removing and Installing the DC-Inpu
- Page 266 and 267: CISCO SYSTEMS, INC Removing and Ins
- Page 268 and 269: CISCO SYSTEMS, INC 1 2 3 4 INPUT OK
- Page 270 and 271: Removing and Installing the DC-Inpu
- Page 272 and 273: CISCO SYSTEMS, INC Removing and Ins
- Page 274 and 275: Removing and Installing the DC-Inpu
- Page 276 and 277: Removing and Installing the DC-Inpu
- Page 278 and 279: Removing and Installing the DC-Inpu
- Page 280 and 281: CISCO SYSTEMS, INC 1 2 3 4 INPUT OK
- Page 282 and 283: Removing and Installing PEMs Chapte
- Page 284 and 285: Removing and Installing PEMs Chapte
- Page 286 and 287: OSM-4OC12 POS-SI 1 2 1 2 1 1 2 2 3
- Page 288 and 289: Removing and Installing the Fan Tra
- Page 290 and 291: WS-X6K-SUP2-2GE OSM-4OC12 POS-SI OS
- Page 292 and 293: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 294 and 295: WS-C6500-SFM SWITCH FABRIC MDL WS-C
- Page 296 and 297: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 298 and 299: Removing and Installing the Fan Tra
- Page 300 and 301: ACTIVE TX RX RX TX ACTIVE TX RX RX
- Page 302 and 303: Installing the Air Filter Assembly
- Page 304 and 305: Installing the Remote Power Cycling
- Page 306 and 307: Installing the Remote Power Cycling
- Page 308 and 309: Installing the Remote Power Cycling
- Page 310 and 311: Power Supply Compatibility Matrix A
- Page 312 and 313: Power Supply Compatibility Matrix A
- Page 316 and 317: 950 W AC-Input and DC-Input Power S
- Page 318 and 319: 1000 W AC-Input Power Supply Append
- Page 320 and 321: 1000 W AC-Input Power Supply Append
- Page 322 and 323: 1300 W AC-Input and DC-Input Power
- Page 324 and 325: 1300 W AC-Input and DC-Input Power
- Page 326 and 327: 1400 W AC-Input Power Supply Append
- Page 328 and 329: 1400 W AC-Input Power Supply Append
- Page 330 and 331: 1400 W AC-Input Power Supply Append
- Page 332 and 333: 2500 W AC-Input and DC-Input Power
- Page 334 and 335: 2500 W AC-Input and DC-Input Power
- Page 336 and 337: 2500 W AC-Input and DC-Input Power
- Page 338 and 339: 2700 W AC-Input and DC-Input Power
- Page 340 and 341: 2700 W AC-Input and DC-Input Power
- Page 342 and 343: 2700 W AC-Input and DC-Input Power
- Page 344 and 345: 3000 W AC-Input Power Supply Append
- Page 346 and 347: 3000 W AC-Input Power Supply Append
- Page 348 and 349: 3000 W AC-Input Power Supply Append
- Page 350 and 351: 4000 W AC-Input and DC-Input Power
- Page 352 and 353: 4000 W AC-Input and DC-Input Power
- Page 354 and 355: 6000 W AC-Input and DC-Input Power
- Page 356 and 357: 6000 W AC-Input and DC-Input Power
- Page 358 and 359: 6000 W AC-Input and DC-Input Power
- Page 360 and 361: 6000 W AC-Input and DC-Input Power
- Page 362 and 363: 8700 W AC-Input Power Supply Append
Appendix A<br />
Power Supply Specifications<br />
950 W AC-Input and DC-Input Power Supplies<br />
Table A-3<br />
950 W AC-Input Power Supply Specifications (continued)<br />
Specification<br />
Branch circuit requirement<br />
Power supply output<br />
capacity<br />
Description<br />
Each chassis power supply should have its own dedicated, fused-branch<br />
circuit:<br />
• For North America—15 A<br />
Power supply output • 15 A @ +1.5 VDC<br />
Output holdup time<br />
kVA rating 1<br />
Heat dissipation<br />
Weight<br />
• For International—Circuits sized to local and national codes<br />
• All <strong>Catalyst</strong> <strong>6500</strong> series AC-input power supplies require<br />
single-phase source AC.<br />
• All AC power supply inputs are fully isolated.<br />
– Source AC can be out of phase between multiple power supplies<br />
in the same chassis, which means that PS1 can be operating<br />
from phase A and PS2 can be operating from phase B.<br />
– For high-line operation, the power supply operates with the hot<br />
conductor wired to a source AC phase and the neutral conductor<br />
wired either to ground or to another source AC phase as long as<br />
the net input voltage is in the range of 170 to 264 VAC.<br />
– Source AC can be out of phase between AC inputs on power<br />
supplies that are equipped with multiple AC inputs, which<br />
means that power cord 1 can be plugged into phase A and<br />
power cord 2 can be plugged into phase B.<br />
950 W maximum (100–240 VAC)<br />
• 2.5 A @ +3.3 VDC<br />
• 19.15 A @ +50 VDC<br />
20 ms minimum<br />
1.32 kVA<br />
4441 BTU/hour (approx.)<br />
8.2 lb (3.7 kg)<br />
1. The kVA rating listed for the power supply should be used as the sizing criteria for both UPS outputs as well as standard<br />
circuits and transformers to power a switch.<br />
OL-5781-08<br />
<strong>Catalyst</strong> <strong>6500</strong> <strong>Series</strong> <strong>Switches</strong> <strong>Installation</strong> <strong>Guide</strong><br />
A-7