Catalyst 6500 Series Switches Installation Guide - Ipland

More documents

Recommendations

Info

Removing and Installing the Fan Tray Chapter 4 Removal and Replacement Procedures Step 6 Tighten the power supply captive installation screws. (See Figure 4-63.) Figure 4-63 DC-Input PEM Catalyst 6503 DC PEM Captive installation screws 79980 Caution Step 7 Step 8 In a system with dual power supplies, connect each power supply to a separate input line. In case of a line failure, the second source will most likely still be available. Remove the safety flag, lockout devices, or tape from the circuit breaker switch handle, and restore power by moving the circuit breaker switch handle to the on (|) position. Verify the power supply operation by ensuring that the power supply front panel LEDs are in the following states: • INPUT OK LED is green • FAN OK LED is green • OUTPUT FAIL LED is not lit If the LEDs indicate a power problem, see the “Identifying Startup Problems” section on page E-3. Removing and Installing the Fan Tray This section describes how to remove and install fan trays for the Catalyst 6500 series switches. Note If your Catalyst 6506, Catalyst 6509, or Catalyst 6509-NEB chassis is equipped with a Supervisor Engine 2 and you using the fan tray removal and replacement procedure to upgrade the chassis from a fan tray 1 (low-speed) to a fan tray 2 (high-speed), you must first check the chassis configuration using the hw-module fan-tray version 2 command to check for configuration problems, such as power supply compatibility and power sufficiency. If the system does not detect any configuration issues, a message is displayed saying that it is OK to change the fan trays. This command applies to Catalyst 6500 series switches that are configured with a Supervisor Engine 2 only. This command is not required in systems that are configured with either a Supervisor Engine 720 or a Supervisor Engine 32. Required Tools You might need a flat-blade or number 2 Phillips-head screwdriver to loosen or tighten the captive installation screws on the fan tray. 4-82 Catalyst 6500 Series Switches Installation Guide OL-5781-08
Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Tray Removing the Fan Tray The fan Tray is designed to be removed and replaced while the system is operating without presenting an electrical hazard or damage to the system. Warning When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the fan blades completely stop before you remove the fan tray. Statement 258 To remove the existing fan assembly, follow these steps: Step 1 Step 2 If you are upgrading your chassis from a fan tray 1 (low speed) to a fan tray 2 (high speed) and your chassis is equipped with a Supervisor Engine 2, you need to check that the current chassis configuration supports the fan tray upgrade. To do this, use the command hw-module fan-tray version 2 to check for configuration problems, such as power supply compatibility and power sufficiency. If the system does not detect any configuration issues, a message is displayed saying that it is OK to change the fan trays. If your chassis has either a Supervisor Engine 32 or a Supervisor Engine 720, skip this step and proceed to Step 2. Locate the fan assembly in the chassis as follows: • Catalyst 6503 and Catalyst 6503-E switches—The fan tray is located to the left of the module cage. (See Figure 4-64.) • Catalyst 6504-E switch—The fan tray is located to the left of the module cage. (See Figure 4-65.) • Catalyst 6506 and Catalyst 6506-E switches—The fan tray is located to the left of the module cage. (See Figure 4-66.) • Catalyst 6509 and Catalyst 6509-E switches—The fan tray is located to the left of the module cage. (See Figure 4-67.) • Catalyst 6509-NEB switch—The fan tray is located above the module cage. (See Figure 4-68.) • Catalyst 6509-NEB-A and Catalyst 6509-V-E switches —On those switch chassis equipped with the optional cable management system, you must first loosen the two captive installation screws located at the top of the cable management system and fold the cable guide down to access the fan assembly. (See Figure 4-69.) See Figure 4-70 for the location of the two fan trays on the Catalyst 6509-NEB-A switch. Note Make sure there is adequate slack in the network interface cables to allow the cable guide to pivot down far enough to access the fan tray. If there is insufficient slack in the cables, the cable guide will not pivot far enough to give you access to the fan trays. Caution Step 3 A fully loaded cable management system can be heavy. Make sure that you provide proper support when lowering the cable guide. • Catalyst 6513 switch—The fan tray is located to the left of the module cage. (See Figure 4-71.) • Catalyst 6513-E switch—The fan tray is located to the left of the module cage. Access to the fan tray is from the rear of the chassis. (See Figure 4-72.) Loosen the two fan tray captive installation screws by turning them counterclockwise. OL-5781-08 Catalyst 6500 Series Switches Installation Guide 4-83
Page 1 and 2:
Catalyst 6500 Series Switches Insta
Page 3:
NOTWITHSTANDING ANY OTHER WARRANTY
Page 6 and 7:
Contents Power Source Interruptions
Page 8 and 9:
Contents Attaching the Interface Ca
Page 10 and 11:
Contents 100-MB Transceivers B-1 1-
Page 12 and 13:
Conventions Preface Chapter Title D
Page 14 and 15:
Conventions Preface Warnings use th
Page 16 and 17:
Conventions Preface Varning! VIKTIG
Page 18 and 19:
Conventions Preface xviii Catalyst
Page 20 and 21:
Related Documentation Preface Obtai
Page 22 and 23:
WS-SUP32-GE-3B Catalyst 6503 Switch
Page 24 and 25:
Catalyst 6503 Switch Chapter 1 Prod
Page 26 and 27:
Page 28 and 29:
WS-SUP32-GE-3B Catalyst 6503-E Swit
Page 30 and 31:
Catalyst 6503-E Switch Chapter 1 Pr
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
WS-X6408 8 PORT GIGABIT ETHERNET WS
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
WS-X6408 WS-X6408 WS-X6408 WS-X6408
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
WS-X6408 WS-X6408 WS-X6408 WS-X6408
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
FAN STATUS LINK LINK LINK LINK LINK
Page 64 and 65:
Catalyst 6509-NEB Switch Chapter 1
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Catalyst 6509-NEB-A Switch Chapter
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Catalyst 6509-V-E Switch Chapter 1
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Safety Chapter 2 Preparing for Inst
Page 98 and 99:
Site Requirements Chapter 2 Prepari
Page 100 and 101:
WS-X6K-SUP2-2GE OSM-4OC12 POS-SI 4
Page 102 and 103:
WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
Page 104 and 105:
Page 106 and 107:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Power Requirements Chapter 2 Prepar
Page 118 and 119:
Cabling Requirements Chapter 2 Prep
Page 120 and 121:
Site Preparation Checklist Chapter
Page 122 and 123:
Chapter 3 Installing the Switch The
Page 124 and 125:
Rack-Mounting Guidelines Chapter 3
Page 126 and 127:
Chassis Installation Kits and Cable
Page 128 and 129:
Installing a Catalyst 6503 or Catal
Page 130 and 131:
CAUTION STATUS LINK CONSOLE LINK LI
Page 132 and 133:
Installing a Catalyst 6504-E Switch
Page 134 and 135:
WS-SUP32-GE-3B CAUTION STATUS LINK
Page 136 and 137:
Installing a Catalyst 6504-E Switch
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
WS-X6408 WS-X6408 WS-X6224 24 PORT
Page 144 and 145:
WS-X6408 WS-X6408 WS-X6224 24 PORT
Page 146 and 147:
Installing a Catalyst 6509-NEB or C
Page 148 and 149:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 150 and 151:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 152 and 153:
WS-C6500-SFM SWITCH FABRIC MDL WS-C
Page 154 and 155:
WS-C6500-SFM SWITCH FABRIC MDL WS-C
Page 156 and 157:
Installing a Catalyst 6509-V-E Swit
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Installing a Catalyst 6513 or Catal
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Generic Installation Procedures Cha
Page 170 and 171:
Generic Installation Procedures Cha
Page 172 and 173:
Establishing the System Ground Chap
Page 174 and 175:
OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
Page 176 and 177:
Page 178 and 179:
1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
Page 180 and 181:
Establishing the System Ground Chap
Page 182 and 183:
Attaching the Interface Cables Chap
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
LINK Attaching the Interface Cables
Page 194 and 195:
LINK Attaching the Interface Cables
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Verifying Switch Chassis Installati
Page 206 and 207:
Verifying Switch Chassis Installati
Page 208 and 209:
Removing and Installing the AC-Inpu
Page 210 and 211:
OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
Page 212 and 213:
Page 214 and 215:
ALL FASTENERS MUST BE FULLY ENGAGED
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
OSM-4OC12 POS-SI 1 2 1 2 1 1 2 2 3
Page 224 and 225:
Removing and Installing the DC-Inpu
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239: Removing and Installing the DC-Inpu
Page 266 and 267: CISCO SYSTEMS, INC Removing and Ins
Page 268 and 269: CISCO SYSTEMS, INC 1 2 3 4 INPUT OK
Page 272 and 273: CISCO SYSTEMS, INC Removing and Ins
Page 280 and 281: CISCO SYSTEMS, INC 1 2 3 4 INPUT OK
Page 282 and 283: Removing and Installing PEMs Chapte
Page 284 and 285: Removing and Installing PEMs Chapte
Page 286 and 287: OSM-4OC12 POS-SI 1 2 1 2 1 1 2 2 3
Page 290 and 291: WS-X6K-SUP2-2GE OSM-4OC12 POS-SI OS
Page 292 and 293: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
Page 294 and 295: WS-C6500-SFM SWITCH FABRIC MDL WS-C
Page 296 and 297: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
Page 298 and 299: Removing and Installing the Fan Tra
Page 300 and 301: ACTIVE TX RX RX TX ACTIVE TX RX RX
Page 302 and 303: Installing the Air Filter Assembly
Page 304 and 305: Installing the Remote Power Cycling
Page 310 and 311: Power Supply Compatibility Matrix A
Page 312 and 313: Power Supply Compatibility Matrix A
Page 314 and 315: 950 W AC-Input and DC-Input Power S
Page 316 and 317: 950 W AC-Input and DC-Input Power S
Page 318 and 319: 1000 W AC-Input Power Supply Append
Page 322 and 323: 1300 W AC-Input and DC-Input Power
Page 338 and 339:
2700 W AC-Input and DC-Input Power
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
3000 W AC-Input Power Supply Append
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
AC Power Cord Illustrations Appendi
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Power Supply Redundancy Appendix A
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Pluggable Transceivers Appendix B T
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Module Connectors Appendix B Transc
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
Page 418 and 419:
Cables Appendix B Transceivers, Mod
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
Cleaning the Fiber-Optic Connectors
Page 426 and 427:
Cleaning the Fiber-Optic Connectors
Page 428 and 429:
Appendix C Repacking the Switch Fig
Page 430 and 431:
Appendix D Chassis and Module Power
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
Solving Problems at the System Comp
Page 448 and 449:
Troubleshooting the Power Supply Ap
Page 450 and 451:
Troubleshooting Modules Appendix E
Page 452 and 453:
Contacting Customer Service Appendi
Page 454 and 455:
Index 4000 W DC-input power supplie
Page 456 and 457:
Index power supplies description 1-
Page 458 and 459:
Index features table 1-69 form fact
Page 460 and 461:
Index Catalyst 6504-E switches 1-14
Page 462 and 463:
Index R DC power cable leads color
Page 464:
Index U startup E-2 supervisor engi
show all

Catalyst 6500 Series Switches Installation Guide - Ipland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?