Catalyst 6500 Series Switches Installation Guide - Ipland
Catalyst 6500 Series Switches Installation Guide - Ipland Catalyst 6500 Series Switches Installation Guide - Ipland
Establishing the System Ground Chapter 3 Installing the Switch Figure 3-33 Installing the System Ground Lug on the 8700 W Power Supply Wire System grounding studs Grounding lug M4 flat washer Split-ring washer M4 nut o INPUT OK FAN OK OUTPUT FAIL NC RELAY 182182 CISCO SYSTEMS, INC. 1 2 3 220VAC 1 2 3 DEFAULT NO RELAY 3-60 Catalyst 6500 Series Switches Installation Guide OL-5781-08
Chapter 3 Installing the Switch Installing the Power Supplies in the Switch Chassis Installing the Power Supplies in the Switch Chassis The chassis secondary power supplies (AC or DC) are shipped separately from the switch chassis. Remove the power supply from its shipping packaging, and then install and connect it to the site power by referring to the “Removing and Installing the AC-Input Power Supplies” section on page 4-2 or the “Removing and Installing the DC-Input Power Supplies” section on page 4-15. Verify that you have the correct power supply (AC-input or DC-input and the correct wattage) for your configuration. Note AC-input and DC-input power supplies can be mixed in a chassis. Attaching the Interface Cables This section provides general information on attaching interface cables to the supervisor engines and to the modules. Note Refer to the Catalyst 6500 Series Switch Module Guide for additional module information. Connecting the Supervisor Engine Console Port This section describes how to connect to the supervisor engine console port from a terminal or modem. The console port on the supervisor engine allows you to perform the following functions: • Configure the switch from the CLI. • Monitor network statistics and errors. • Configure SNMP agent parameters. • Download software updates to the switch, or distribute software images residing in flash memory to attached devices. The console port, located on the front panel of the supervisor engine, is shown in Figure 3-34. Figure 3-34 Supervisor Engine Console Port Connector WS-X6K-SUP2-2GE STATUS SYSTEM CONSOLE PWR LIGHT RESET CONSOLE PORT MODE SUPERVISOR 2 CONSOLE 62226 OL-5781-08 Catalyst 6500 Series Switches Installation Guide 3-61
- Page 130 and 131: CAUTION STATUS LINK CONSOLE LINK LI
- Page 132 and 133: Installing a Catalyst 6504-E Switch
- Page 134 and 135: WS-SUP32-GE-3B CAUTION STATUS LINK
- Page 136 and 137: Installing a Catalyst 6504-E Switch
- Page 138 and 139: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 140 and 141: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 142 and 143: WS-X6408 WS-X6408 WS-X6224 24 PORT
- Page 144 and 145: WS-X6408 WS-X6408 WS-X6224 24 PORT
- Page 146 and 147: Installing a Catalyst 6509-NEB or C
- Page 148 and 149: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 150 and 151: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 152 and 153: WS-C6500-SFM SWITCH FABRIC MDL WS-C
- Page 154 and 155: WS-C6500-SFM SWITCH FABRIC MDL WS-C
- Page 156 and 157: Installing a Catalyst 6509-V-E Swit
- Page 158 and 159: Installing a Catalyst 6509-V-E Swit
- Page 160 and 161: Installing a Catalyst 6509-V-E Swit
- Page 162 and 163: Installing a Catalyst 6513 or Catal
- Page 164 and 165: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 166 and 167: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 168 and 169: Generic Installation Procedures Cha
- Page 170 and 171: Generic Installation Procedures Cha
- Page 172 and 173: Establishing the System Ground Chap
- Page 174 and 175: OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
- Page 176 and 177: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 178 and 179: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 182 and 183: Attaching the Interface Cables Chap
- Page 184 and 185: Attaching the Interface Cables Chap
- Page 186 and 187: Attaching the Interface Cables Chap
- Page 188 and 189: Attaching the Interface Cables Chap
- Page 190 and 191: Attaching the Interface Cables Chap
- Page 192 and 193: LINK Attaching the Interface Cables
- Page 194 and 195: LINK Attaching the Interface Cables
- Page 196 and 197: Attaching the Interface Cables Chap
- Page 198 and 199: Attaching the Interface Cables Chap
- Page 200 and 201: Attaching the Interface Cables Chap
- Page 202 and 203: Attaching the Interface Cables Chap
- Page 204 and 205: Verifying Switch Chassis Installati
- Page 206 and 207: Verifying Switch Chassis Installati
- Page 208 and 209: Removing and Installing the AC-Inpu
- Page 210 and 211: OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
- Page 212 and 213: Removing and Installing the AC-Inpu
- Page 214 and 215: ALL FASTENERS MUST BE FULLY ENGAGED
- Page 216 and 217: Removing and Installing the AC-Inpu
- Page 218 and 219: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 220 and 221: Removing and Installing the AC-Inpu
- Page 222 and 223: OSM-4OC12 POS-SI 1 2 1 2 1 1 2 2 3
- Page 224 and 225: Removing and Installing the DC-Inpu
- Page 226 and 227: Removing and Installing the DC-Inpu
- Page 228 and 229: Removing and Installing the DC-Inpu
Chapter 3<br />
Installing the Switch<br />
Installing the Power Supplies in the Switch Chassis<br />
Installing the Power Supplies in the Switch Chassis<br />
The chassis secondary power supplies (AC or DC) are shipped separately from the switch chassis.<br />
Remove the power supply from its shipping packaging, and then install and connect it to the site power<br />
by referring to the “Removing and Installing the AC-Input Power Supplies” section on page 4-2 or the<br />
“Removing and Installing the DC-Input Power Supplies” section on page 4-15. Verify that you have the<br />
correct power supply (AC-input or DC-input and the correct wattage) for your configuration.<br />
Note<br />
AC-input and DC-input power supplies can be mixed in a chassis.<br />
Attaching the Interface Cables<br />
This section provides general information on attaching interface cables to the supervisor engines and to<br />
the modules.<br />
Note<br />
Refer to the <strong>Catalyst</strong> <strong>6500</strong> <strong>Series</strong> Switch Module <strong>Guide</strong> for additional module information.<br />
Connecting the Supervisor Engine Console Port<br />
This section describes how to connect to the supervisor engine console port from a terminal or modem.<br />
The console port on the supervisor engine allows you to perform the following functions:<br />
• Configure the switch from the CLI.<br />
• Monitor network statistics and errors.<br />
• Configure SNMP agent parameters.<br />
• Download software updates to the switch, or distribute software images residing in flash memory to<br />
attached devices.<br />
The console port, located on the front panel of the supervisor engine, is shown in Figure 3-34.<br />
Figure 3-34<br />
Supervisor Engine Console Port Connector<br />
WS-X6K-SUP2-2GE<br />
STATUS<br />
SYSTEM<br />
CONSOLE<br />
PWR LIGHT<br />
RESET<br />
CONSOLE<br />
PORT<br />
MODE<br />
SUPERVISOR 2<br />
CONSOLE<br />
62226<br />
OL-5781-08<br />
<strong>Catalyst</strong> <strong>6500</strong> <strong>Series</strong> <strong>Switches</strong> <strong>Installation</strong> <strong>Guide</strong><br />
3-61