Catalyst 6500 Series Switches Installation Guide - Ipland
Catalyst 6500 Series Switches Installation Guide - Ipland Catalyst 6500 Series Switches Installation Guide - Ipland
WS-SUP32-GE-3B CAUTION STATUS LINK LINK STATUS LINK LINK LINK LINK LINK LINK EJECT LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK LINK PORT 9 PORT 9 LINK LINK LINK LINK Installing a Catalyst 6504-E Switch Chassis Chapter 3 Installing the Switch Step 2 Remove the chassis shipping bracket before you install the chassis in the rack. Perform the following substeps: a. Loosen and remove the four M5 screws that secure the chassis shipping bracket to the chassis rack mount brackets. (See Figure 3-5.) b. Lift up slightly on the shipping bracket to disengage the two shipping bracket hooks from the rack-mount L brackets. c. Remove the shipping bracket and save it. You must reinstall the shipping bracket if you relocate the chassis. Figure 3-5 Removing the Catalyst 6504-E Chassis Shipping Bracket 2 CATALYST 65 0 SUPERVISOR ENGINE 32 WS-SUP32-GE-3B CATALYST 65 0 SUPERVISOR ENGINE 32 WS-X6516-GE-T X CONSOLE CONSOLE EJECT 280385 DISK 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8 16 PORT 1000 BASE-T GE DISK 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 WS-X6516-GE-T X 16 PORT 1000 BASE-T GE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 THIS BRACKET IS FOR SHIPPING PURPOSES ONLY. YOU MUST REMOVE THIS BRACKET BEFORE SYSTEM INSTALLATION AND USE. DO NOT DISCARD THIS BRACKET. THIS BRACKET MUST BE REPLACED ON THE CHASSIS FOR FUTURE SHIPMENTS. 47-195 2-01 REV A0 1 1 Chassis shipping bracket 2 M5 Phillips-head screws (4x) 3-14 Catalyst 6500 Series Switches Installation Guide OL-5781-08
Chapter 3 Installing the Switch Installing a Catalyst 6504-E Switch Chassis Step 3 With a person standing at each side of the chassis, grasp the chassis handle with one hand, and use the other hand near the back of the chassis for balance. Slowly lift the chassis in unison. Avoid sudden twists or moves to prevent injury. Tip Step 4 Step 5 Step 6 Step 7 Have a third person install the rack-mount screws while two people support the chassis in the rack enclosure. Align the mounting holes in the rack-mount bracket with the mounting holes in the equipment rack. If you want to install one or both of the optional cable guides, position the cable guides so that the cable guide mounting holes are aligned with rack-mount holes and the rack post holes. Install a minimum of eight 10-32 or 12-24 screws (four on each side) through the cable guide mounting holes, rack-mount bracket holes, rack post holes, and into the clip nuts to secure the cable guides and the chassis to the rack post. (See Figure 3-6.) Use a tape measure or a level to verify that the chassis is installed straight and level. Figure 3-6 Installing a Catalyst 6504-E Switch Chassis in a Rack FAN STATUS STATUS STATUS 126563 OL-5781-08 Catalyst 6500 Series Switches Installation Guide 3-15
- Page 84 and 85: Catalyst 6513 Switch Chapter 1 Prod
- Page 86 and 87: Catalyst 6513 Switch Chapter 1 Prod
- Page 88 and 89: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 90 and 91: Catalyst 6513-E Switch Chapter 1 Pr
- Page 92 and 93: Catalyst 6513-E Switch Chapter 1 Pr
- Page 94 and 95: Catalyst 6513-E Switch Chapter 1 Pr
- Page 96 and 97: Safety Chapter 2 Preparing for Inst
- Page 98 and 99: Site Requirements Chapter 2 Prepari
- Page 100 and 101: WS-X6K-SUP2-2GE OSM-4OC12 POS-SI 4
- Page 102 and 103: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 104 and 105: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 106 and 107: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 108 and 109: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 110 and 111: Site Requirements Chapter 2 Prepari
- Page 112 and 113: Site Requirements Chapter 2 Prepari
- Page 114 and 115: Site Requirements Chapter 2 Prepari
- Page 116 and 117: Power Requirements Chapter 2 Prepar
- Page 118 and 119: Cabling Requirements Chapter 2 Prep
- Page 120 and 121: Site Preparation Checklist Chapter
- Page 122 and 123: Chapter 3 Installing the Switch The
- Page 124 and 125: Rack-Mounting Guidelines Chapter 3
- Page 126 and 127: Chassis Installation Kits and Cable
- Page 128 and 129: Installing a Catalyst 6503 or Catal
- Page 130 and 131: CAUTION STATUS LINK CONSOLE LINK LI
- Page 132 and 133: Installing a Catalyst 6504-E Switch
- Page 136 and 137: Installing a Catalyst 6504-E Switch
- Page 138 and 139: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 140 and 141: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 142 and 143: WS-X6408 WS-X6408 WS-X6224 24 PORT
- Page 144 and 145: WS-X6408 WS-X6408 WS-X6224 24 PORT
- Page 146 and 147: Installing a Catalyst 6509-NEB or C
- Page 148 and 149: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 150 and 151: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 152 and 153: WS-C6500-SFM SWITCH FABRIC MDL WS-C
- Page 154 and 155: WS-C6500-SFM SWITCH FABRIC MDL WS-C
- Page 156 and 157: Installing a Catalyst 6509-V-E Swit
- Page 158 and 159: Installing a Catalyst 6509-V-E Swit
- Page 160 and 161: Installing a Catalyst 6509-V-E Swit
- Page 162 and 163: Installing a Catalyst 6513 or Catal
- Page 164 and 165: WS-X6408 8 PORT GIGABIT ETHERNET WS
- Page 166 and 167: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 168 and 169: Generic Installation Procedures Cha
- Page 170 and 171: Generic Installation Procedures Cha
- Page 172 and 173: Establishing the System Ground Chap
- Page 174 and 175: OSM-4OC12 POS-SI 2 1 2 1 4 2 3 1 4
- Page 176 and 177: WS-X6K-SUP2-2GE SUPERVISOR2 WS-X6K-
- Page 178 and 179: 1 2 3 4 5 6 7 8 9 10 1 1 2 12 3 4 5
- Page 180 and 181: Establishing the System Ground Chap
- Page 182 and 183: Attaching the Interface Cables Chap
WS-SUP32-GE-3B<br />
CAUTION<br />
STATUS<br />
LINK<br />
LINK<br />
STATUS<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
EJECT<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
PORT 9<br />
PORT 9<br />
LINK<br />
LINK<br />
LINK<br />
LINK<br />
Installing a <strong>Catalyst</strong> 6504-E Switch Chassis<br />
Chapter 3<br />
Installing the Switch<br />
Step 2<br />
Remove the chassis shipping bracket before you install the chassis in the rack. Perform the following<br />
substeps:<br />
a. Loosen and remove the four M5 screws that secure the chassis shipping bracket to the chassis rack<br />
mount brackets. (See Figure 3-5.)<br />
b. Lift up slightly on the shipping bracket to disengage the two shipping bracket hooks from the<br />
rack-mount L brackets.<br />
c. Remove the shipping bracket and save it. You must reinstall the shipping bracket if you relocate the<br />
chassis.<br />
Figure 3-5<br />
Removing the <strong>Catalyst</strong> 6504-E Chassis Shipping Bracket<br />
2<br />
CATALYST 65 0 SUPERVISOR ENGINE 32<br />
WS-SUP32-GE-3B<br />
CATALYST 65 0 SUPERVISOR ENGINE 32<br />
WS-X6516-GE-T X<br />
CONSOLE<br />
CONSOLE<br />
EJECT<br />
280385<br />
DISK 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8<br />
16 PORT 1000 BASE-T GE<br />
DISK 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8<br />
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16<br />
WS-X6516-GE-T X<br />
16 PORT 1000 BASE-T GE<br />
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16<br />
THIS BRACKET IS FOR SHIPPING PURPOSES<br />
ONLY. YOU MUST REMOVE THIS BRACKET<br />
BEFORE SYSTEM INSTALLATION AND USE.<br />
DO NOT DISCARD THIS BRACKET.<br />
THIS BRACKET MUST BE REPLACED ON THE<br />
CHASSIS FOR FUTURE SHIPMENTS.<br />
47-195 2-01 REV A0<br />
1<br />
1 Chassis shipping bracket 2 M5 Phillips-head screws (4x)<br />
3-14<br />
<strong>Catalyst</strong> <strong>6500</strong> <strong>Series</strong> <strong>Switches</strong> <strong>Installation</strong> <strong>Guide</strong><br />
OL-5781-08