14.11.2014 Views

Catalyst 6500 Series Switches Installation Guide - Ipland

Catalyst 6500 Series Switches Installation Guide - Ipland

Catalyst 6500 Series Switches Installation Guide - Ipland

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

CAUTION<br />

STATUS<br />

LINK<br />

CONSOLE<br />

LINK<br />

LINK<br />

LINK<br />

EJECT<br />

EJECT<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

LINK<br />

PORT 9<br />

PORT 9<br />

LINK<br />

LINK<br />

Installing a <strong>Catalyst</strong> 6503 or <strong>Catalyst</strong> 6503-E Switch Chassis<br />

Chapter 3<br />

Installing the Switch<br />

Figure 3-2<br />

Removing the <strong>Catalyst</strong> 6503-E Chassis Shipping Bracket<br />

2<br />

WS-SUP32-GE-3B<br />

CATALYST 65 0 SUPERVISOR ENGINE 32<br />

WS-SUP32-GE-3B<br />

CONSOLE<br />

280384<br />

CATALYST 65 0 SUPERVISOR ENGINE 32<br />

DISK 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8<br />

WS-X6516-GE-T X<br />

16 PORT 1000 BASE-T GE<br />

DISK 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8<br />

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16<br />

THIS BRACKET IS FOR SHIPPING PURPOSES<br />

ONLY. YOU MUST REMOVE THIS BRACKET<br />

BEFORE SYSTEM INSTALLATION AND USE.<br />

DO NOT DISCARD THIS BRACKET.<br />

THIS BRACKET MUST BE REPLACED ON THE<br />

CHASSIS FOR FUTURE SHIPMENTS.<br />

47-195 2-01 REV A0<br />

1<br />

1 Chassis shipping bracket 2 M5 Phillips-head screws (4x)<br />

Step 3<br />

With a person standing at each side of the chassis, grasp the chassis handle with one hand, and use the<br />

other hand near the back of the chassis for balance. Slowly lift the chassis in unison. Avoid sudden twists<br />

or moves to prevent injury.<br />

Tip<br />

Step 4<br />

Step 5<br />

Step 6<br />

Step 7<br />

Have a third person install the rack-mount screws while two people support the chassis in the rack<br />

enclosure.<br />

Align the mounting holes in the rack-mount bracket with the mounting holes in the equipment rack.<br />

If you want to install one or both of the optional cable guides, position the cable guide so that the cable<br />

guide mounting holes are aligned with rack-mount holes and the rack post holes. (See Figure 3-3.)<br />

Install a minimum of eight 10-32 or 12-24 screws (four on each side) through the cable guide mounting<br />

holes, rack-mount bracket holes, rack post holes, and into the clip nuts to secure the cable guides and the<br />

chassis to the rack post. (See Figure 3-3.)<br />

Use a tape measure or level to verify that the chassis is installed straight and level.<br />

3-10<br />

<strong>Catalyst</strong> <strong>6500</strong> <strong>Series</strong> <strong>Switches</strong> <strong>Installation</strong> <strong>Guide</strong><br />

OL-5781-08

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!