SHIPLAP DURAPLATE LOWER HORIZONTAL PANEL SPLICE ...
SHIPLAP DURAPLATE LOWER HORIZONTAL PANEL SPLICE ... SHIPLAP DURAPLATE LOWER HORIZONTAL PANEL SPLICE ...
® Shiplap DuraPlate Lower Horizontal Panel Splice Layout and Mark the Lower Panel Splice 1. Measure and layout the interior cut line by measuring up from the base rail 5- 1 /4", then count upward 13 rivets. Drill out the 13th rivet to transfer the reference mark from the outside wall to the interior. From the inside, measure down 5 /8" from the center of the rivet hole. Refer to Figure 26. This method will allow for inconsistencies in the exterior wall surface of the lower panel. Do the same at numerous places along the 52 ft. length. 2. Stretch a chalk line and mark where the cut will be made along both outside and inside walls. When marking the side walls, align the chalk line at the top portion of the drilled holes prior to snapping the string. 22 7 / 8 " CUTLINE Figure 4, Marking the Cut-line 6
® Shiplap DuraPlate Lower Horizontal Panel Splice 22 7 / 8 " CUTLINE Figure 5, Drilling 1 /4" Holes Figure 6, Transferring the Cut-line Inside from Front to Rear Between Holes 7
- Page 1 and 2: DuraPlate ® Repair Manual for: ¤
- Page 3 and 4: ® Shiplap DuraPlate Lower Horizont
- Page 5 and 6: ® Shiplap DuraPlate Lower Horizont
- Page 7 and 8: ® Shiplap DuraPlate Lower Horizont
- Page 9: ® Shiplap DuraPlate Lower Horizont
- Page 13 and 14: ® Shiplap DuraPlate Lower Horizont
- Page 15 and 16: ® Shiplap DuraPlate Lower Horizont
- Page 17 and 18: ® Shiplap DuraPlate Lower Horizont
- Page 19 and 20: ® Shiplap DuraPlate Lower Horizont
- Page 21 and 22: ® Shiplap DuraPlate Lower Horizont
- Page 23 and 24: ® Shiplap DuraPlate Lower Horizont
- Page 25 and 26: ® Shiplap DuraPlate Lower Horizont
- Page 27 and 28: ® Shiplap DuraPlate Lower Horizont
- Page 29 and 30: ® Shiplap DuraPlate Lower Horizont
- Page 31 and 32: ® Shiplap DuraPlate Lower Horizont
- Page 33 and 34: ® Shiplap DuraPlate Lower Horizont
- Page 36: ® © 2004 Wabash Technology Corp.
®<br />
Shiplap DuraPlate Lower Horizontal Panel Splice<br />
Layout and Mark the Lower Panel Splice<br />
1. Measure and layout the interior cut line by measuring up from the base<br />
rail 5- 1 /4", then count upward 13 rivets. Drill out the 13th rivet to transfer<br />
the reference mark from the outside wall to the interior. From the inside,<br />
measure down 5 /8" from the center of the rivet hole. Refer to Figure<br />
26. This method will allow for inconsistencies in the exterior wall surface<br />
of the lower panel. Do the same at numerous places along the 52 ft.<br />
length.<br />
2. Stretch a chalk line and mark where the cut will be made along both<br />
outside and inside walls. When marking the side walls, align the chalk line<br />
at the top portion of the drilled holes prior to snapping the string.<br />
22 7 / 8 "<br />
CUTLINE<br />
Figure 4, Marking the Cut-line<br />
6