instruction book - Janome

More documents

Recommendations

Info

18 Round end/Keyhole buttonhole Machine setting 2 1 2 3 Pattern #18, #19 or #21 LED display Foot R: Automatic buttonhole foot 19 1 The sewing sequence is the same as sensor buttonhole. Refer to pages 26, 27, 28 for sewing <strong>instruction</strong>. 1 Starting point 2 End point 2 1 21 2 1 Adjusting the buttonhole width 1 18 21 2 3 Press the plus (+) key to increase buttonhole width. Press the minus (–) key to decrease buttonhole width. The width of round end buttonhole can be varied from 2.5 to 5.5. 2 Narrow buttonhole (2.5mm wide) 3 Wide buttonhole (5.5mm wide) The width of keyhole buttonhole can be varied from 5.0 to 7.0. 2 3 Narrow buttonhole (5.0mm wide) Wide buttonhole (7.0mm wide) 1 19 Refer to page 29 for stitch density adjustment. 2 3 30
1 17 Auto 2 0 3 Auto 9 #17 Square buttonhole (Auto buttonhole) Machine setting 1 Pattern #17 2 Foot R: Automatic buttonhole foot 3 Thread tension Auto 1 2 3 1 Mark the buttonhole position on the fabric. Pull the button holder all the way out. 2 Draw the needle thread to the left through the hole on the foot. 3 Place the fabric under the foot and lower the needle at A 1 the starting point by turning the handwheel. Lower the foot. 1 Button holder 2 Starting point 2 NOTE: You do not need to pull down the buttonhole lever. 4 Step 1 Step 2 Step 3 Step 4 4 Depress the foot control and follow the steps below. Step 1: Sew up the left row to the desired buttonhole length and stop the machine. Press the reverse stitch button. Step 2: Depress the foot control again. The machine will automatically tack and sew down the right row. Stop the machine when you return to the starting point. Press the reverse stitch button. Step 3: Depress the foot control again. The machine will sew the front bartack and stop automatically. Step 4: After the buttonhole is completed, a blinking dot will appear on the LED display. Raise the presser foot. NOTE: The blinking dot indicates that the buttonhole length has been memorized. If you wish to alter the stitch density, you need to re-select the auto buttonhole and repeat the above steps with a new stitch setting. To sew buttonholes in the same size, simply depress the foot control. Keep the foot control depressed and the machine will sew the same sized buttonhole and stop automatically. You do not need to press the reverse stitch button. The LED display shows “ 0 ” while sewing. 31
Page 1 and 2: INSTRUCTION BOOK
Page 3 and 4: TABLE OF CONTENTS Name of Parts ...
Page 5 and 6: 5 4 Standard Accessories and Storag
Page 7 and 8: 3 1 2 GETTING READY TO SEW Connecti
Page 9 and 10: 1 3 2 4 5 Dropping the Feed Dog The
Page 11 and 12: Raising and Lowering the Presser Fo
Page 13 and 14: 2 1 3 Winding the Bobbin • Removi
Page 15 and 16: 3 1 2 1 Threading the Machine • T
Page 17 and 18: 1 Drawing Up Bobbin Thread 1 Raise
Page 19 and 20: 1 2 3 01 0 UTILITY STITCHES Auto 9
Page 21 and 22: 1 2 • Using the seam guide lines
Page 23 and 24: 1 2 3 05 0 Auto 9 Basic Zigzag Stit
Page 25 and 26: 1 2 3 11 0 Auto 9 • Overedge stit
Page 27 and 28: Automatic Buttonhole 16 Sensor Vari
Page 29 and 30: 4 10 4 Raise the buttonhole foot an
Page 31: 1 1 Adjusting the buttonhole width
Page 35 and 36: 1 2 3 01 0 Auto 9 Zipper Applicatio
Page 37 and 38: 5 5 Detach the foot and attach it w
Page 39 and 40: 1 2 3 15 0 Auto 9 Blind Hem Stitch
Page 41 and 42: 1 25 2 SEWING APPLICATION AND DECOR
Page 43 and 44: 1 2 3 44 0 Auto 9 Fagoting Machine
Page 45 and 46: 1 2 3 42 54 0 Auto 9 Pattern Combin
Page 47 and 48: 1 2 3 30 0 Auto 9 Decorative Stretc
Page 49 and 50: 1 2 1 Cleaning Hook Race and Feed D
Page 51 and 52: TROUBLESHOOTING Condition The needl

instruction book - Janome

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?