Telemetry Module MT-021 User Manual

More documents

Recommendations

Info

6.2.8.3.6. SMTP user name Function - Allows to enter user name which will be used during authentication process on SMTP server, e.g. john.smith Data type - text Range - 0..31 characters Default value - Comments - 6.2.8.3.7. SMTP password Function - Allows to enter password which will be used during authentication process on SMTP server, e.g. j0h2ny$m1th Data type - text Range - 0..31 characters Default value - Comments - 6.2.8.3.8. E-mail sending rules 1...16 Each of rules residing on the list is defined by following parameters: Triggering event Receiver e-mail address E-mail title E-mail text 6.2.8.3.8.1. Triggering event Function - Assigns which one of previously defined event will trigger sending of a particular text message. Data type - selection list Range - None or names of events from the Events table Default value - None Comments - N/A 6.2.8.3.8.2. Receiver e-mail address Function - Allows to enter receiver e-mail address, e.g. jane.brown@other_company.com Data type - text Range - 0..31 characters Default value - Comments - 63
6.2.8.3.8.3. E-mail title Function - Defines an e-mail title Data type - text Range - 0..31 characters Default value - Comments - 6.2.8.3.8.4. E-mail text Function - Defines text of an message Data type - text Range - 0..160 characters Default value - Comments - Text may contain any string of characters, except diacritical signs. It may contain mnemonics dynamically replaced at run-time by values drawn from the module e.g.: time, register or logical state of the bit. The syntax of commands is described in detail in Syntax of commands for reading and writing data by SMS paragraph. 6.3. Configuration writing After required modifications and parameter settings, the configuration is stored on the configuring PC's hard disk only. In order to write it to the module memory, it has to be transmitted to the module. For local configuration, it is enough to secure a connection via RS232 cable. Detailed description of local configuration is to be found in the MTM user manual. Remote configuration can be realized via SMS commands. It is necessary to enter the phone number on an authorized list, except for the first configuration of the module. Detailed description of remote configuration is to be found in the chapter Module configuration via SMS. 6.4. Verification of configuration Despite high reliability of both local and remote module configuration, verify of it is important. It is relevant if the module's behavior does not comply in accordance with the performed configuration. For verification, please read the configuration from the module and check parameters settings. Reading of module configuration is described in details in MTM user manual and chapter Module configuration via SMS. 64
Page 2 and 3:
Telemetry Module MT-021 User Manual
Page 4 and 5:
INDEX 1. MODULE'S DESTINATION .....
Page 6 and 7:
6.2.6.1.3.2. Input type ...........
Page 8:
9.2.2. Hearing aids................
Page 11 and 12:
3.2. Power supply MT-021 may be pow
Page 13 and 14:
3.5. Antenna Attachment of antenna
Page 15 and 16: Any of binary inputs I1...I4 may op
Page 17: 3.7.6. Event logger MT-021 automati
Page 20 and 21: In next steps you will see how to c
Page 22 and 23: Create Event EVT1 (in this example
Page 24 and 25: Next press Connect button (Transmis
Page 26 and 27: 5. Connections scheme The chapter s
Page 28 and 29: 5.3. Relay outputs Q1...Q4 Telemetr
Page 30 and 31: Current output sensor 5.5. 1-Wire i
Page 32 and 33: 6.2.1. Header Header of parameter s
Page 34 and 35: 6.2.1.11. Last reading time Functio
Page 36 and 37: Yes All SMS messages are sent regar
Page 38 and 39: HH - if placed in this format text
Page 40 and 41: Default value - 1 Comments - N/A 6.
Page 42 and 43: whether transmission is still possi
Page 44 and 45: 6.2.6.1. Terminals Sub-group Termin
Page 46 and 47: 6.2.6.1.2.1. Name Function - Define
Page 48 and 49: Range Default value Comments - 0...
Page 50 and 51: Data type - number Range - 0...3276
Page 52 and 53: 6.2.6.1.4.2.1.6. Deadband Function
Page 54 and 55: 6.2.6.3.3. Logged information Funct
Page 56 and 57: Default value - None Comments - N/A
Page 58 and 59: 6.2.7.7. Trigger source (Flags) Fun
Page 60 and 61: Default value - Yes Comments - N/A
Page 62 and 63: Default value - Comments - 6.2.8.1.
Page 64 and 65: 6.2.8.2.1. Number of CLIP calls rul
Page 68 and 69: 7. Technical Data 7.1. General Dime
Page 70 and 71: 7.7. Drawings and dimensions (All d
Page 72 and 73: 8.2. Unblocking of SIM card Three f
Page 74 and 75: 10.2. Module configuration via SMS
Page 76 and 77: Authorized numbers group: * - index
Page 78 and 79: Synchronous timers TMR1...TMR4 grou
Page 80 and 81: Rules group: * - index from 1 to 16
Page 82 and 83: &ADMIN#LPHN=6#SMST_6="Mark"#SMSN_6=
Page 84 and 85: causes module to write value 1234 t
Page 86 and 87: UT LD UD T{1..2} S F[1..3] UTC time
Page 88 and 89: eturned string will look like: >25/
Page 90 and 91: Address Dec Bit address 0 1 2 3 4 5
Page 92 and 93: "GSM Status" register flags descrip
Page 94: 10.5. Flags During operation MT-021
show all

Telemetry Module MT-021 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?