Telemetry Module MT-021 User Manual

More documents

Recommendations

Info

5.3. Relay outputs Q1...Q4 <strong>Telemetry</strong> module has 4 normally open (NO) relay outputs marked as Q1 ... Q4. The outputs operate independently and are isolated from each other. Connection scheme: Notice! Maximum voltage between contacts is 230V AC Maximum switching current is 6A. 5.4. Analog inputs AN1, AN2 Analog inputs AN1 and AN2 can be used for measuring temperature using Pt-100 and NTC sensors or collecting measurements via current (4-20mA) or voltage signal (0-5V/0-10V). Mode of operation is user-configurable. Below are shown proper connection schematics: 25
Pt-100 - 2 wire (AN1 only) Pt-100 - 3 wire (AN1 only) NTC (AN2 only) Voltage output sensor 26
Page 2 and 3: Telemetry Module MT-021 User Manual
Page 4 and 5: INDEX 1. MODULE'S DESTINATION .....
Page 6 and 7: 6.2.6.1.3.2. Input type ...........
Page 8: 9.2.2. Hearing aids................
Page 11 and 12: 3.2. Power supply MT-021 may be pow
Page 13 and 14: 3.5. Antenna Attachment of antenna
Page 15 and 16: Any of binary inputs I1...I4 may op
Page 17: 3.7.6. Event logger MT-021 automati
Page 20 and 21: In next steps you will see how to c
Page 22 and 23: Create Event EVT1 (in this example
Page 24 and 25: Next press Connect button (Transmis
Page 26 and 27: 5. Connections scheme The chapter s
Page 30 and 31: Current output sensor 5.5. 1-Wire i
Page 32 and 33: 6.2.1. Header Header of parameter s
Page 34 and 35: 6.2.1.11. Last reading time Functio
Page 36 and 37: Yes All SMS messages are sent regar
Page 38 and 39: HH - if placed in this format text
Page 40 and 41: Default value - 1 Comments - N/A 6.
Page 42 and 43: whether transmission is still possi
Page 44 and 45: 6.2.6.1. Terminals Sub-group Termin
Page 46 and 47: 6.2.6.1.2.1. Name Function - Define
Page 48 and 49: Range Default value Comments - 0...
Page 50 and 51: Data type - number Range - 0...3276
Page 52 and 53: 6.2.6.1.4.2.1.6. Deadband Function
Page 54 and 55: 6.2.6.3.3. Logged information Funct
Page 56 and 57: Default value - None Comments - N/A
Page 58 and 59: 6.2.7.7. Trigger source (Flags) Fun
Page 60 and 61: Default value - Yes Comments - N/A
Page 62 and 63: Default value - Comments - 6.2.8.1.
Page 64 and 65: 6.2.8.2.1. Number of CLIP calls rul
Page 66 and 67: 6.2.8.3.6. SMTP user name Function
Page 68 and 69: 7. Technical Data 7.1. General Dime
Page 70 and 71: 7.7. Drawings and dimensions (All d
Page 72 and 73: 8.2. Unblocking of SIM card Three f
Page 74 and 75: 10.2. Module configuration via SMS
Page 76 and 77: Authorized numbers group: * - index
Page 78 and 79:
Synchronous timers TMR1...TMR4 grou
Page 80 and 81:
Rules group: * - index from 1 to 16
Page 82 and 83:
&ADMIN#LPHN=6#SMST_6="Mark"#SMSN_6=
Page 84 and 85:
causes module to write value 1234 t
Page 86 and 87:
UT LD UD T{1..2} S F[1..3] UTC time
Page 88 and 89:
eturned string will look like: >25/
Page 90 and 91:
Address Dec Bit address 0 1 2 3 4 5
Page 92 and 93:
"GSM Status" register flags descrip
Page 94:
10.5. Flags During operation MT-021
show all

Telemetry Module MT-021 User Manual

Create successful ePaper yourself

Delete template?

Save as template?