Telemetry Module MT-021 User Manual

More documents

Recommendations

Info

5. Connections scheme The chapter shows standard configurations securing proper operation of MT-021 module's integral inputs/outputs in all available operating modes. 5.1. Power supply MT-021 module can be powered from any DC power source providing voltage within the range 9-30 VDC. Notice! Exceeding the range of power supply may cause faulty operation or damage the module! Notice! Supply cables length < 10m. Signal cables length < 30m. For longer cables it is recommended to use external overvoltage protection. 23
5.2. Binary inputs I1 ... I4 Internal optoisolated binary inputs marked as I1...I4 may work only in positive logic. All binary inputs have same reference - module's electrical ground - negative pole of the power supply connected to GND pin. Connection scheme: Notice! Supply cables length < 10m. Signal cables length < 30m. For longer cables it is recommended to use external overvoltage protection. 24
Page 2 and 3: Telemetry Module MT-021 User Manual
Page 4 and 5: INDEX 1. MODULE'S DESTINATION .....
Page 6 and 7: 6.2.6.1.3.2. Input type ...........
Page 8: 9.2.2. Hearing aids................
Page 11 and 12: 3.2. Power supply MT-021 may be pow
Page 13 and 14: 3.5. Antenna Attachment of antenna
Page 15 and 16: Any of binary inputs I1...I4 may op
Page 17: 3.7.6. Event logger MT-021 automati
Page 20 and 21: In next steps you will see how to c
Page 22 and 23: Create Event EVT1 (in this example
Page 24 and 25: Next press Connect button (Transmis
Page 28 and 29: 5.3. Relay outputs Q1...Q4 Telemetr
Page 30 and 31: Current output sensor 5.5. 1-Wire i
Page 32 and 33: 6.2.1. Header Header of parameter s
Page 34 and 35: 6.2.1.11. Last reading time Functio
Page 36 and 37: Yes All SMS messages are sent regar
Page 38 and 39: HH - if placed in this format text
Page 40 and 41: Default value - 1 Comments - N/A 6.
Page 42 and 43: whether transmission is still possi
Page 44 and 45: 6.2.6.1. Terminals Sub-group Termin
Page 46 and 47: 6.2.6.1.2.1. Name Function - Define
Page 48 and 49: Range Default value Comments - 0...
Page 50 and 51: Data type - number Range - 0...3276
Page 52 and 53: 6.2.6.1.4.2.1.6. Deadband Function
Page 54 and 55: 6.2.6.3.3. Logged information Funct
Page 56 and 57: Default value - None Comments - N/A
Page 58 and 59: 6.2.7.7. Trigger source (Flags) Fun
Page 60 and 61: Default value - Yes Comments - N/A
Page 62 and 63: Default value - Comments - 6.2.8.1.
Page 64 and 65: 6.2.8.2.1. Number of CLIP calls rul
Page 66 and 67: 6.2.8.3.6. SMTP user name Function
Page 68 and 69: 7. Technical Data 7.1. General Dime
Page 70 and 71: 7.7. Drawings and dimensions (All d
Page 72 and 73: 8.2. Unblocking of SIM card Three f
Page 74 and 75: 10.2. Module configuration via SMS
Page 76 and 77:
Authorized numbers group: * - index
Page 78 and 79:
Synchronous timers TMR1...TMR4 grou
Page 80 and 81:
Rules group: * - index from 1 to 16
Page 82 and 83:
&ADMIN#LPHN=6#SMST_6="Mark"#SMSN_6=
Page 84 and 85:
causes module to write value 1234 t
Page 86 and 87:
UT LD UD T{1..2} S F[1..3] UTC time
Page 88 and 89:
eturned string will look like: >25/
Page 90 and 91:
Address Dec Bit address 0 1 2 3 4 5
Page 92 and 93:
"GSM Status" register flags descrip
Page 94:
10.5. Flags During operation MT-021
show all

Telemetry Module MT-021 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?