Telemetry Module MT-021 User Manual

More documents

Recommendations

Info

Next press Connect button (Transmission->Connect) then Write button (Transmission->Write). At the end synchronize device RT using Set time button (Configuration->Set time). Now setting binary input in high logical state, e.g. by connecting V+ cable with terminal I1 and power GND with binary inputs GND, will result in sending SMS that reads ‘ALARM ‘ to +48111222333. 4.2. Remote configuration via SMS Configuration described in chapter Configurating MT-021 using MTManager can be also written to module using SMS commands. Those commands, their default values and allowed value ranges are described in chapter Appendices/Module configuration via SMS. Below you can find sample configuration SMS: 21
&#SPIN="2323"#CONF_PSW="PASS"#SMSN_1="+48111222333"#EVNO=1 #EV_TRIG_1=2#EV_FLAG_1=0#EV_EDGE_1=1#TRNO=1#TR_TRIG_1=1 #TR_TCH_1=1#TR_T_1="ALARM"#TR_N_1=1 That SMS sets: SIM card PIN number (2323) Configuration password (PASS) First telephone on Authorized->Phone list (+48111222333) Event EVT1 triggered when binary input I1 changes its logical state 0->1 SMS sending rule 1 which will send SMS saying ALARM to previously defined telephone number each time event EVT1 is triggered. As an answer to this SMS module will send back the same text preceding it with '>' sign. After first configuration it is good to adjust module RTC. SMS below sets time to last second of 2010: &PASS#CRTC="2010-12-31 23:59:59" SMS begins new password set by previous configuration SMS preceded by '&' sign. First configuration can be done from any phone number. Any following SMS configuration commands will be accepted only from numbers placed on Authorized list. Therefore it is vital to enter at least one phone number to that list during first configuration. Maximum length of SMS configuration command should not exceed 160 signs. Now setting binary input in high logical state, e.g. by connecting V+ cable with terminal I1 and power GND with binary inputs GND, will result in sending SMS that reads ‘ALARM ‘ to +48111222333. 4.3. How do I disable a SIM PIN number The procedure for setting the SIM mode to allow its use without requiring a PIN (e.g. Nokia, model 6210): Place the SIM card into the appropriate slot on the phone. Turn on the phone, and enter the correct PIN number for your SIM card. From the available commands, select Menu\Settings\Security Settings. Choose menu PIN code request then press Select, you will be prompted for a PIN number. Then select OFF response to a question PIN code request At the end appears a message PIN code request is not active. 22
Page 2 and 3: Telemetry Module MT-021 User Manual
Page 4 and 5: INDEX 1. MODULE'S DESTINATION .....
Page 6 and 7: 6.2.6.1.3.2. Input type ...........
Page 8: 9.2.2. Hearing aids................
Page 11 and 12: 3.2. Power supply MT-021 may be pow
Page 13 and 14: 3.5. Antenna Attachment of antenna
Page 15 and 16: Any of binary inputs I1...I4 may op
Page 17: 3.7.6. Event logger MT-021 automati
Page 20 and 21: In next steps you will see how to c
Page 22 and 23: Create Event EVT1 (in this example
Page 26 and 27: 5. Connections scheme The chapter s
Page 28 and 29: 5.3. Relay outputs Q1...Q4 Telemetr
Page 30 and 31: Current output sensor 5.5. 1-Wire i
Page 32 and 33: 6.2.1. Header Header of parameter s
Page 34 and 35: 6.2.1.11. Last reading time Functio
Page 36 and 37: Yes All SMS messages are sent regar
Page 38 and 39: HH - if placed in this format text
Page 40 and 41: Default value - 1 Comments - N/A 6.
Page 42 and 43: whether transmission is still possi
Page 44 and 45: 6.2.6.1. Terminals Sub-group Termin
Page 46 and 47: 6.2.6.1.2.1. Name Function - Define
Page 48 and 49: Range Default value Comments - 0...
Page 50 and 51: Data type - number Range - 0...3276
Page 52 and 53: 6.2.6.1.4.2.1.6. Deadband Function
Page 54 and 55: 6.2.6.3.3. Logged information Funct
Page 56 and 57: Default value - None Comments - N/A
Page 58 and 59: 6.2.7.7. Trigger source (Flags) Fun
Page 60 and 61: Default value - Yes Comments - N/A
Page 62 and 63: Default value - Comments - 6.2.8.1.
Page 64 and 65: 6.2.8.2.1. Number of CLIP calls rul
Page 66 and 67: 6.2.8.3.6. SMTP user name Function
Page 68 and 69: 7. Technical Data 7.1. General Dime
Page 70 and 71: 7.7. Drawings and dimensions (All d
Page 72 and 73: 8.2. Unblocking of SIM card Three f
Page 74 and 75:
10.2. Module configuration via SMS
Page 76 and 77:
Authorized numbers group: * - index
Page 78 and 79:
Synchronous timers TMR1...TMR4 grou
Page 80 and 81:
Rules group: * - index from 1 to 16
Page 82 and 83:
&ADMIN#LPHN=6#SMST_6="Mark"#SMSN_6=
Page 84 and 85:
causes module to write value 1234 t
Page 86 and 87:
UT LD UD T{1..2} S F[1..3] UTC time
Page 88 and 89:
eturned string will look like: >25/
Page 90 and 91:
Address Dec Bit address 0 1 2 3 4 5
Page 92 and 93:
"GSM Status" register flags descrip
Page 94:
10.5. Flags During operation MT-021
show all

Telemetry Module MT-021 User Manual

Create successful ePaper yourself

Delete template?

Save as template?