Telemetry Module MT-021 User Manual

More documents

Recommendations

Info

In next steps you will see how to create basic configuration, which can be described by following points: Entering PIN code, Adding telephone number to authorized phone list, Defining event for binary input I1 when it is changing its state from 0 to 1 (rising edge), Defining SMS sending rule which will send SMS that reads “ALARM” to a predefined phone number when previously configured event is triggered, Setting RTC clock of the device. 4.1. Configuring MT-021 using MTManager Install MTManager on your PC from CD provided with module. When installed with default setting MTManager creates shortcuts on Desktop and in Start menu. Please proceed to next step. Start MTManager by double-click on shortcut icon: In newly created MTManager project add new module using main menu option General->New->Module. 17
Choose MT-021 as type, type module name (e.g. ST_1) in name field and select firmware version (firmware version is marked on the box). In the next step set parameters essential for establishing GSM connection: SIM card PIN number (required if PIN code request is on Configuration password to protect module from unauthorized access. Open Authorized numbers -> Phone and add to the list new telephone number which will be receiving SMS messages from device (e.g. +48111222333). 18
Page 2 and 3: Telemetry Module MT-021 User Manual
Page 4 and 5: INDEX 1. MODULE'S DESTINATION .....
Page 6 and 7: 6.2.6.1.3.2. Input type ...........
Page 8: 9.2.2. Hearing aids................
Page 11 and 12: 3.2. Power supply MT-021 may be pow
Page 13 and 14: 3.5. Antenna Attachment of antenna
Page 15 and 16: Any of binary inputs I1...I4 may op
Page 17: 3.7.6. Event logger MT-021 automati
Page 22 and 23: Create Event EVT1 (in this example
Page 24 and 25: Next press Connect button (Transmis
Page 26 and 27: 5. Connections scheme The chapter s
Page 28 and 29: 5.3. Relay outputs Q1...Q4 Telemetr
Page 30 and 31: Current output sensor 5.5. 1-Wire i
Page 32 and 33: 6.2.1. Header Header of parameter s
Page 34 and 35: 6.2.1.11. Last reading time Functio
Page 36 and 37: Yes All SMS messages are sent regar
Page 38 and 39: HH - if placed in this format text
Page 40 and 41: Default value - 1 Comments - N/A 6.
Page 42 and 43: whether transmission is still possi
Page 44 and 45: 6.2.6.1. Terminals Sub-group Termin
Page 46 and 47: 6.2.6.1.2.1. Name Function - Define
Page 48 and 49: Range Default value Comments - 0...
Page 50 and 51: Data type - number Range - 0...3276
Page 52 and 53: 6.2.6.1.4.2.1.6. Deadband Function
Page 54 and 55: 6.2.6.3.3. Logged information Funct
Page 56 and 57: Default value - None Comments - N/A
Page 58 and 59: 6.2.7.7. Trigger source (Flags) Fun
Page 60 and 61: Default value - Yes Comments - N/A
Page 62 and 63: Default value - Comments - 6.2.8.1.
Page 64 and 65: 6.2.8.2.1. Number of CLIP calls rul
Page 66 and 67: 6.2.8.3.6. SMTP user name Function
Page 68 and 69: 7. Technical Data 7.1. General Dime
Page 70 and 71:
7.7. Drawings and dimensions (All d
Page 72 and 73:
8.2. Unblocking of SIM card Three f
Page 74 and 75:
10.2. Module configuration via SMS
Page 76 and 77:
Authorized numbers group: * - index
Page 78 and 79:
Synchronous timers TMR1...TMR4 grou
Page 80 and 81:
Rules group: * - index from 1 to 16
Page 82 and 83:
&ADMIN#LPHN=6#SMST_6="Mark"#SMSN_6=
Page 84 and 85:
causes module to write value 1234 t
Page 86 and 87:
UT LD UD T{1..2} S F[1..3] UTC time
Page 88 and 89:
eturned string will look like: >25/
Page 90 and 91:
Address Dec Bit address 0 1 2 3 4 5
Page 92 and 93:
"GSM Status" register flags descrip
Page 94:
10.5. Flags During operation MT-021
show all

Telemetry Module MT-021 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?