Lantech LGS-1104 User Manual
Lantech LGS-1104 User Manual Lantech LGS-1104 User Manual
Hardware Description This section mainly describes the hardware of the 4 10/100/1000T + 1 Mini-GBIC Web Managed Switch, and gives a physical and functional overview on certain switch. Physical dimension The 4 10/100/1000T + 1 Mini-GBIC Web Managed Switch physical dimension is 165 x 100 x 32.5 mm (W x D x H). Front Panel The Front Panel of the 4 10/100/1000T + 1 Mini-GBIC Web Managed Switch consists of LED Indicators and a reset button. Please refer to LED Indicator section for LED description. • Reset button: It provides an easy way for user to reset the configuration back to the default settings. Press the button more than 5 seconds, and then the switch will restart and set all configurations back to the default settings. 4
Rear Panel The rear panel consists of the 4 10/100/1000Base-TX RJ-45 port, one Mini GBIC slot, and DC Power Jack as shown in the figure below. The switch will work with DC in the range of 12V/0.8A. The Rear Panel of 4 10/100/1000T + 1 Mini-GBIC Web Managed Switch • RJ-45 Ports (Auto MDI/MDIX): 4x 10/100/1000 N-way auto-sensing for 10Base-T, 100Base-TX or 1000Base-T connections. In general, MDI means connecting to another Hub or Switch while MDIX means connecting to a workstation or PC. Therefore, Auto MDI/MDIX would allow connecting to another Switch or workstation without changing non-crossover or crossover cabling. • Mini GBIC slot: The appropriate replaceable Mini-GBIC port is available with a variety of different transmitter and receiver types, allowing users to select the appropriate transceiver for each link to provide the required optical reach over the available optical fiber type. There is one LED indicator—LNK/ACT—for Mini-GBIC port on the front panel. LED Indicators The LED Indicators display the real-time information of systematic operation status. Please see definition of the LED indicators as follows. 5
- Page 1 and 2: Lantech LGS-1104 4 10/100/1000T + 1
- Page 3 and 4: Content FCC Warning ...............
- Page 5 and 6: Introduction The 4 10/100/1000T + 1
- Page 7: Spanning Tree IEEE802.1w rapid span
- Page 11 and 12: Desktop Installation Set the switch
- Page 13 and 14: Two 4 10/100/1000T + 1 Mini-GBIC We
- Page 15 and 16: 4. Key in the default password as
- Page 17 and 18: failure (The default IP is 192.168.
- Page 19 and 20: Statistics-2 (Detailed) The followi
- Page 21 and 22: Disable the awareness so that ports
- Page 23 and 24: • Click Apply to have the configu
- Page 25 and 26: • Hello Time (1-10): The scale of
- Page 27 and 28: 802.1X Configuration IEEE 802.1X is
- Page 29 and 30: • Or, click Refresh to refresh th
- Page 31 and 32: QoS DSCP Mapping interface • Afte
- Page 33 and 34: • And then, press Upload to updat
- Page 35 and 36: Troubleshooting This section is int
- Page 37 and 38: Technical Specification This sectio
- Page 39 and 40: Operating Humidity 10% to 90% (Non-
- Page 41 and 42: Straight-through cable schematic Cr
Rear Panel<br />
The rear panel consists of the 4 10/100/1000Base-TX RJ-45 port, one Mini GBIC<br />
slot, and DC Power Jack as shown in the figure below. The switch will work with<br />
DC in the range of 12V/0.8A.<br />
The Rear Panel of 4 10/100/1000T + 1 Mini-GBIC Web Managed Switch<br />
• RJ-45 Ports (Auto MDI/MDIX): 4x 10/100/1000 N-way auto-sensing for<br />
10Base-T, 100Base-TX or 1000Base-T connections.<br />
In general, MDI means connecting to another Hub or Switch while MDIX<br />
means connecting to a workstation or PC. Therefore, Auto MDI/MDIX<br />
would allow connecting to another Switch or workstation without changing<br />
non-crossover or crossover cabling.<br />
• Mini GBIC slot: The appropriate replaceable Mini-GBIC port is available<br />
with a variety of different transmitter and receiver types, allowing users to<br />
select the appropriate transceiver for each link to provide the required<br />
optical reach over the available optical fiber type. There is one LED<br />
indicator—LNK/ACT—for Mini-GBIC port on the front panel.<br />
LED Indicators<br />
The LED Indicators display the real-time information of systematic operation<br />
status. Please see definition of the LED indicators as follows.<br />
5