TL-WR542G 54M Wireless Router - TP-Link

More documents

Recommendations

Info

First, please choose the WAN Connection Type (Dynamic IP/Static IP/PPPoE/802.1X + Dynamic IP/802.1X + Static IP/Big Pond Cable/L2TP/PPTP) for Internet. The default type is Dynamic IP. If you aren’t given any login parameters (fixed IP Address, logging ID, etc), please select Dynamic IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and a password, please select the type of your ISP provided (PPPoE/BigPond/L2TP/PPTP). If you are not sure which connection type you use currently, please contact your ISP to obtain the correct information. 1. If you choose Dynamic IP, the router will automatically get IP parameters from your ISP. You can see the page as follows (Figure 4-4): Figure 4-4 WAN – Dynamic IP This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP. Note: 17
If you get address and find error when you go to a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses. Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you can choose this option. (This is rarely required.) 2. If you choose Static IP, you should have fixed IP Parameters specified by your ISP. The Static IP settings page will appear, shown in Figure 4-5: Figure 4-5 WAN - Static IP You should type the following parameters into the spaces provided: ‣ IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ‣ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. ‣ Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP. ‣ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. ‣ Primary DNS - (Optional) Enter the DNS address in dotted-decimal notation provided by your ISP. ‣ Secondary DNS - (Optional) Type another DNS address in dotted-decimal notation provided by your ISP if provided. 3. If you choose PPPoE, you should enter the following parameters (Figure 4-6): 18
Page 1 and 2: TL-WR542G 54M Wireless Router Rev:
Page 3 and 4: FCC STATEMENT This equipment has be
Page 5 and 6: For the following equipment: TP-LIN
Page 7 and 8: 4.8 Security ......................
Page 9 and 10: Chapter 1. Introduction Thank you f
Page 11 and 12: Figure 1-1 Front Panel sketch Name
Page 13 and 14: Chapter 2. Connecting the Router 2.
Page 15 and 16: Chapter 3. Quick Installation Guide
Page 17 and 18: If the router's IP address is 192.1
Page 19 and 20: Figure 3-8 Quick Setup - Static IP
Page 21 and 22: menus on the left of the Web-based
Page 23: 4.4 Network Figure 4-2 the Network
Page 27 and 28: Time-based Connecting function can
Page 29 and 30: Click Logout to end 802.1X authenti
Page 31 and 32: ‣ Connect Automatically - Connect
Page 33 and 34: Figure 4-12 PPTP Settings ‣ User
Page 35 and 36: Click Restore Factory MAC to restor
Page 37 and 38: Note Dialog Note: Limited by local
Page 39 and 40: format stands for any combination o
Page 41 and 42: ‣ Privilege - Select the privileg
Page 43 and 44: pull-down list, enter 2F34D20BE2E54
Page 45 and 46: ‣ Address Lease Time - The Addres
Page 47 and 48: 2. Modify the information. 3. Click
Page 49 and 50: 3. Click the Save button. Click the
Page 51 and 52: There are many popular applications
Page 53 and 54: 4.8 Security Figure 4-33 The Securi
Page 55 and 56: 1. Effective Time - Enter a range o
Page 57 and 58: to 17:05. 2. Domain Name - Type the
Page 59 and 60: To modify or delete an existing ent
Page 61 and 62: etween 5 ~ 3600 packets. When the c
Page 63 and 64: Click the Enable All button to make
Page 65 and 66: 4.11.1 Binding Setting This page di
Page 67 and 68: • MAC Address - The MAC address o
Page 69 and 70: Figure 4-52 Oray.net DDNS Settings
Page 71 and 72: There are nine submenus under the S
Page 73 and 74: 1. Do not turn off the router or pr
Page 75 and 76:
Figure 4-60 Password It is recommen
Page 77 and 78:
Figure 4-63 Statistics ‣ Current
Page 79 and 80:
Appendix A: FAQ 1. How do I configu
Page 81 and 82:
Figure A-5 Add or Modify a Virtual
Page 83 and 84:
3) Make sure the wireless stations
Page 85 and 86:
Figure 0-2 5) The following TCP/IP
Page 87 and 88:
Now: Click OK to keep your settings
Page 89 and 90:
Appendix D: Glossary ‣ 2x to 3x e
show all

TL-WR542G 54M Wireless Router - TP-Link

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?