Seatbelt Installation Instructions Series IIA & III with Hard & Soft Tops
Seatbelt Installation Instructions Series IIA & III with Hard & Soft Tops
Seatbelt Installation Instructions Series IIA & III with Hard & Soft Tops
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
INSTRUCTIONS: RTC1939I<br />
T H E S P E C I A L I S T S I N L A N D R O V E R S • U S A<br />
<strong>Seatbelt</strong> <strong>Installation</strong> <strong>Instructions</strong><br />
<strong>Series</strong> <strong>IIA</strong> & <strong>III</strong> <strong>with</strong> <strong>Hard</strong> & <strong>Soft</strong> <strong>Tops</strong><br />
Introduction: This kit comes <strong>with</strong> a pair of seatbelts and the mounting hardware to install inertia seatbelts in the front of an<br />
88” Land Rover that was previously fitted <strong>with</strong> lap belts or static shoulder belts. This kit includes two seatbelt reels and receivers.<br />
PLEASE NOTE THAT THE BELTS ARE PARTIALLY EXTENDED FROM THE REELS. TAKE CARE NOT TO ALLOW TOO MUCH OF THE<br />
BELT TO BE TAKEN UP ON THE REEL WHICH CAN CAUSE IT TO JAM. The kit also contains four square plates, (two <strong>with</strong> fixed<br />
nuts and two <strong>with</strong> a pair of 7/16” holes), two reel brackets, two aluminum guide plates, two steel guide plates, and one bag of<br />
hardware.<br />
1) Install lower anchor bracket at the seat-box base and rear door post<br />
using existing holes and 1/4” hardware. Note that these brackets are<br />
already mounted in most Rovers and are not included in seatbelt kit.<br />
2) An upper mounting point can be added to Rovers fitted <strong>with</strong> a hard<br />
top. This bracket, not included in this kit, is usually already in place in late<br />
<strong>Series</strong> <strong>IIA</strong>’s & <strong>III</strong>’s. To install this bracket remove the interior trim. Hold<br />
the bracket up <strong>with</strong> the flat side facing you and two holes up. Mark the<br />
three hole positions and drill for 5/16” hardware.<br />
3) The seatbelt kit contains two type of 5.5” square mounting plates.<br />
To mount the reel in an 88” Rover <strong>with</strong> either a soft top or full hard top, use<br />
the plate <strong>with</strong>out the fixed nut. Position the plate approximately 1” down<br />
from the galvanized trim on the seat bulkhead and the 1” over from the inset on the front side of the bulkhead. Drill and mount<br />
<strong>with</strong> 3/16” rivets supplied so the two large holes are towards the bottom. Drill reel bracket holes to 3/8”. Mount the reel to the<br />
bracket (MRC4687) being careful not to allow the belt to wind any further onto the reel and mount the assembly to the bulkhead<br />
(fig. 3 & 4).<br />
4) Position the two guide plates directly above the reel <strong>with</strong> the aluminum plate under the steel plate so that it raps over the rear<br />
side of the galvanized top cap. Mark the top cap and drill for 5/16” hardware. Insert the belt in the guide plate and mount the<br />
plates to top cap. If the upper mounting bracket is not being used, as <strong>with</strong> soft tops, position the pivot point bracket below the<br />
guide or cut the pivot bracket to remove it all together. If the upper mount is used, bolt the pivot bracket to it.<br />
5) The receivers can be installed in a couple of methods. Most <strong>Series</strong> <strong>IIA</strong> Rovers have gusset brackets behind the bulkhead.<br />
When using these brackets, switch the receivers so that the one marked for the right is used on the left and vice-versa. <strong>Series</strong> <strong>III</strong><br />
Rovers should have brackets to mount the receiver down through the horizontal section in front of the bulkhead. Receivers<br />
Page 1 of 2<br />
1 802 879-0032 or 1-800-403-7591 • Fax: (802) 879-9152<br />
email@roversnorth.com • www.roversnorth.com<br />
Rovers North, Inc. • 1319 VT Rt. 128 • Westford, Vermont • 05494-9601 USA
INSTRUCTIONS: RTC1939I<br />
T H E S P E C I A L I S T S I N L A N D R O V E R S • U S A<br />
mounted in this fashion are mounted and indicated, right on the right. In Rovers <strong>with</strong> no pre-existing mounting point, use the<br />
square plate <strong>with</strong> the fixed nut. Position the plate on the back side of the bulkhead measuring over 8 1/2” from the side of the<br />
wheel well to the edge of the plate. With the bolt hole towards the top, mark its location. Remove the plate and drill for 7/16”<br />
hardware. Reposition the plate and mount the receiver using the right one on the left. Drill out the rivet holes and install 3/16”<br />
rivets.<br />
6) Attach the end of the belt to the bracket mounts in the corner of the seat-base. On Rovers <strong>with</strong> upper mounting brackets,<br />
mount the pivot bracket to the bracket installed in step 2. The seatbelt installation should now be complete.<br />
Page 2 of 2<br />
1 802 879-0032 or 1-800-403-7591 • Fax: (802) 879-9152<br />
email@roversnorth.com • www.roversnorth.com<br />
Rovers North, Inc. • 1319 VT Rt. 128 • Westford, Vermont • 05494-9601 USA
T H E S P E C I A L I S T S I N L A N D R O V E R S • U S A<br />
<strong>Instructions</strong> Questionnaire<br />
We rely on our customers to help us continually improve our instruction sheets. Please FAX or mail any comments, questions, or<br />
ideas for improvements you may have.<br />
Send To: Rovers North<br />
1319 Vermont Route 128<br />
Westford, VT 05494<br />
or Fax: 802-879-9152<br />
Your Name: _____________________ Phone #: ________________<br />
Address: _____________________ Email Adrs: ________________<br />
_____________________<br />
Instruction part number (top right corner) or description of what instructions are: ________________________________<br />
Overall, how would you rate the quality of this set of instructions? (please circle one):<br />
Poor Fair Good Very Good Excellent<br />
1 2 3 4 5 6 7 8 9 10<br />
Ideas, Comments, or Corrections (please include specifics, such as page number, or step number):<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
_________________________________________________________________________________________<br />
THANK YOU!<br />
1 802 879-0032<br />
or (800) 403-7591 • Fax: (802) 879-9152<br />
email@roversnorth.com • www.roversnorth.com<br />
Rovers North, Inc. • 1319 VT Rt. 128 • Westford, Vermont • 05494-9601 USA