Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Type indication (relief valve – direct operated type for vent control)<br />
Relief valve – direct operated<br />
type for vent control<br />
Nominal dimension<br />
6, <strong>10</strong><br />
Connection method<br />
G = G thread connection type<br />
GO = G thread connection type (based on JISB2351 0 type)<br />
R = R thread connection type<br />
P = Gasket connection type<br />
C = Cartridge type<br />
Series number: <strong>10</strong><br />
Type of hydraulic oil<br />
No symbol = Mineral based hydraulic oil<br />
V<br />
W<br />
= Phosphate ester based hydraulic oil<br />
= Fatty ester based hydraulic oil<br />
Water-glycol based hydraulic oil<br />
(Note) In the case of the cartridge type, “No symbol” and<br />
“W” are identical, and therefore, there is no “W”.<br />
P port restriction contraction diameter<br />
<strong>10</strong><br />
12<br />
15<br />
18<br />
=<br />
=<br />
=<br />
=<br />
1.0mm<br />
1.2mm<br />
1.5mm<br />
1.8mm<br />
Relief valve – Direct operated type<br />
Shape of pressure adjusting part<br />
1 = Handle adjustment<br />
2 = Thread adjustment (with cap)<br />
3 = Handle with key adjustment<br />
Specifications<br />
Nominal dimension 6<br />
Maximum working<br />
pressure<br />
MPa (kgf/cm 2 )<br />
Port P<br />
Port T<br />
39.2 (400)<br />
30.9 (315)<br />
Maximum flow rate L/min<br />
Thread connection type<br />
3 (Note)<br />
1.5<br />
Mass kg Gasket connection type<br />
Cartridge type<br />
1.5<br />
0.4<br />
(Note) Be very careful that the minimum adjustment<br />
pressure and pressure override values differ<br />
depending on the flow rate used and<br />
restriction and contraction diameters of the<br />
main relief valve and relief valve for vent<br />
control.<br />
Highest adjustment pressure<br />
<strong>10</strong>0 = 9.8MPa (<strong>10</strong>0kgf/cm 2 )<br />
315 = 30.9MPa (315kgf/cm 2 )<br />
Precautions in use<br />
● Make the vent conduit as short as<br />
possible and the inside diameter of<br />
piping as small as possible. If the<br />
inside volume of the vent conduit is<br />
large, control may become unstable.<br />
● Do not connect the tank piping to<br />
other tank piping but connect it<br />
directly to the tank.<br />
●For the pressure increase value per turn of the adjust thread, refer to the section of the type number index “RD6 to 30”.<br />
Type indication (relief valve for panel mounted vent control )<br />
Relief valve for panel<br />
mounted vent control<br />
Nominal dimension<br />
6<br />
Connection method<br />
R = R thread connection type<br />
Series number: <strong>10</strong><br />
Shape of pressure adjusting part<br />
3 = Handle with key adjustment<br />
Type of hydraulic oil<br />
No symbol = Mineral based hydraulic oil<br />
Fatty ester based hydraulic oil<br />
Water-glycol based hydraulic oi<br />
V = Phosphate ester based hydraulic oil<br />
P port restriction contraction diameter<br />
<strong>10</strong><br />
12<br />
15<br />
18<br />
=<br />
=<br />
=<br />
=<br />
1.0mm<br />
1.2mm<br />
1.5mm<br />
1.8mm<br />
Highest adjustment pressure<br />
315 = 30.9MPa (315kgf/cm 2 )<br />
(Pressure adjustment range = 2 to 30.9 MPa)<br />
Specifications<br />
Nominal dimension 6<br />
Maximum working pressure MPa (kgf/cm 2 )<br />
30.9 (315)<br />
Maximum flow rate L/min<br />
3 (Note)<br />
Operating force<br />
Maximum approx. 2 Nm (20 kgfcm) (however, in the case of back pressure being 0)<br />
Mass kg<br />
1.5<br />
(Note) Be very careful that the minimum adjustment pressure and pressure override values differ depending<br />
on the flow rate used and restriction and contraction diameters of the main relief valve and relief valve<br />
for vent control.<br />
Precautions in use<br />
● Make the vent conduit as short as<br />
possible and the inside diameter of<br />
piping as small as possible. If the<br />
inside volume of the vent conduit is<br />
large, control may become unstable.<br />
● Do not connect the tank piping to<br />
other tank piping but connect it<br />
directly to the tank.<br />
2-4