DH6/10
DH6/10 DH6/10
Manual selector valve – KLA type Manual selector valve – KLA type T A P B ●Hydraulic symbols A B P R ■Overview This manual selector valve is used for controlling start and stop, and movement direction of the hydraulic system with handle operation. ■Specifications Nominal dimension 6 Maximum working pressure Port A, B, P 24.5 (250) MPa (kgf/cm 2 ) Port R 2.9 (30) Maximum flow rate L/min 20 Mass kg 1.9 ■Type indication Manual selector valve with 4 port detent Nominal dimension: 6 Connection method EP = Gasket connection type Type of hydraulic oilMineral based hydraulic oil No symbol Mineral based hydraulic oil V Phosphate ester based hydraulic oil W Fatty ester based hydraulic oil Water-glycol based hydraulic oil Series number: 10 Spool type: 2C ■Sub-plate Valve type Sub-plate type Connection diameter Mass K4LA P-DE6R14-0 P-DE6G14-0 P-DE6R38-0 P-DE6G38-0 When you use a sub-plate, please place an order for the above sub-plate type. For the dimension drawing, refer to page 11 of the appendix. ■Dimension drawing Rc 1 4 G 1 4 Rc 3 8 G 3 8 1.0kg 2.2kg ■Accessories ●Mounting bolt Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm) K4LAR6EP M5×75L 6.9± 1.0 (70±10.5) ●K4LAR6 Switching position When pressed in When pulled out L 2mm 8mm 50 φ35 Ball φ40 31 188.5 15 A R B φ40 6 93.5 Stroke amount 35 8 32 71 6 32.5 26.6 16.3 P *L 19 27.8 40.5 11 10.3 O-ring...JIS B2401 P9 Hs90 4-φ6 4-M5 (for port A, B, P, R) 4-φ12 60 1-64
Check valve (1) Thread connection type Gasket connection type Check valve (1) Overview Features Hydraulic symbols This check valve is used for allowing the flow from one direction to pass freely according to the cracking pressure of the valve and for blocking the flow from the opposite direction. 1. There are an in-line type that has thread connection system and a right angle type that has gasket connection system. 2. There are six types of cracking pressure with no spring: 0.01, 0.05, 0.15, 0.29 and 0.39 MPa. 3. Cartridge type elements are also manufactured. Type indication C Check valve Nominal dimension 6, 8, 10, 15, 20, 25, 30 (Gasket connection type is 10, 20 and 30 only.) Connection method G = GO R P C = = = = G thread connection type G thread connection type (based on JIS B2351 0 type) R thread connection type Gasket connection type Cartridge type (for in-line) Series number: 10 C1M Type of hydraulic oil (Specify only in the case of gasket connection type.) No symbol = Mineral based hydraulic oil V = Phosphate ester based hydraulic oil W = Fatty ester based hydraulic oil Water-glycol based hydraulic oil (Note) It is not necessary to enter the type of hydraulic oil when the connection method is other than “P”. Cracking pressure 00 = No spring (There is no no-spring type in the case of cartridge type.) 01= 0.01MPa(0.1kgf/cm 2 ) 05= 0.05MPa(0.5kgf/cm 2 ) 15= 0.15MPa(1.5kgf/cm 2 ) 30= 0.29MPa(3.0kgf/cm 2 ) 40= 0.39MPa(4.0kgf/cm 2 ) Cartridge type check valve for angle Nominal dimension 6, 8, 10, 15, 20, 25, 30 Connection method C = Cartridge type Series number: 10 Type of hydraulic oil No symbol = Mineral based hydraulic oil Phosphate ester based hydraulic oil Fatty ester based hydraulic oil Water-glycol based hydraulic oil Cracking pressure 01= 0.01MPa(0.1kgf/cm 2 ) 05= 0.05MPa(0.5kgf/cm 2 ) 15= 0.15MPa(1.5kgf/cm 2 ) 30= 0.29MPa(3.0kgf/cm 2 ) 40= 0.39MPa(4.0kgf/cm 2 ) 1-65
- Page 20 and 21: Solenoid operated directional valve
- Page 22 and 23: Solenoid operated directional valve
- Page 24 and 25: Solenoid operated directional valve
- Page 26 and 27: Solenoid controlled pilot operated
- Page 28 and 29: Solenoid controlled pilot operated
- Page 30 and 31: Solenoid controlled pilot operated
- Page 32 and 33: Solenoid controlled pilot operated
- Page 34 and 35: Solenoid controlled pilot operated
- Page 36 and 37: Solenoid controlled pilot operated
- Page 38 and 39: Solenoid controlled pilot operated
- Page 40 and 41: Solenoid controlled pilot operated
- Page 42 and 43: Solenoid controlled pilot operated
- Page 44 and 45: Solenoid controlled pilot operated
- Page 46 and 47: Pilot operated directional valve (1
- Page 48 and 49: Pilot operated directional valve (1
- Page 50 and 51: Pilot operated directional valve (2
- Page 52 and 53: Pilot operated directional valve (2
- Page 54 and 55: Pilot operated directional valve (2
- Page 56 and 57: Pilot operated directional valve (3
- Page 58 and 59: Pilot operated directional valve (3
- Page 60 and 61: Pilot operated directional valve (3
- Page 62 and 63: Manual selector valve (1) Spool typ
- Page 64 and 65: Manual selector valve (1) ■Dimens
- Page 66 and 67: Manual selector valve (2) Spool typ
- Page 68 and 69: Manual selector valve (2) ■Dimens
- Page 72 and 73: Check valve (1) ■Specifications N
- Page 74 and 75: Check valve (1) ●C (cartridge typ
- Page 76 and 77: Amount of pressure drop (MPa Check
- Page 78 and 79: 45° Check valve (2) ●C (flange c
- Page 80 and 81: Pilot operated check valve (1) Sub-
- Page 82 and 83: A Y B X Pilot operated check valve
- Page 84 and 85: Pilot operated check valve (2) Flan
- Page 86 and 87: Pressure gauge valve Pressure gauge
- Page 88 and 89: Page Relief valve - Direct operated
- Page 90 and 91: Hydraulic symbols Pressure increase
- Page 92 and 93: Pressure override characteristics (
- Page 94 and 95: Dimension drawing RD*G/R RDV6G/R L2
- Page 96 and 97: RDV1M6R A 62 Maximum of 152 61 14.5
- Page 98 and 99: Type indication RBE Relief valve -
- Page 100 and 101: Pilot valve The type indication of
- Page 102 and 103: Dimension drawing RB*P B1 B2 X P T
- Page 104 and 105: Relief valve - Balanced piston type
- Page 106 and 107: Type indication RB35X Pilot relief
- Page 108 and 109: RB35F 38 19 110 Y port G1/4 screw d
- Page 110 and 111: Type indication RB52 Relief valve-
- Page 112 and 113: Pilot valve The type indication of
- Page 114 and 115: Three stage pressure relief valve 3
- Page 116 and 117: Dimension drawing 3RBE L10 L1 L8 L3
- Page 118 and 119: Pressure override characteristics (
Check valve (1)<br />
Thread connection type<br />
Gasket connection type<br />
Check valve (1)<br />
<br />
<br />
<br />
<br />
Overview<br />
Features<br />
Hydraulic symbols<br />
This check valve is used for allowing the flow<br />
from one direction to pass freely according to<br />
the cracking pressure of the valve and for<br />
blocking the flow from the opposite direction.<br />
1. There are an in-line type that has thread<br />
connection system and a right angle type that<br />
has gasket connection system.<br />
2. There are six types of cracking pressure with<br />
no spring: 0.01, 0.05, 0.15, 0.29 and 0.39 MPa.<br />
3. Cartridge type elements are also<br />
manufactured.<br />
<br />
<br />
Type indication<br />
C<br />
Check valve<br />
Nominal dimension<br />
6, 8, <strong>10</strong>, 15, 20, 25, 30<br />
(Gasket connection type is <strong>10</strong>, 20 and 30 only.)<br />
Connection method<br />
G =<br />
GO<br />
R<br />
P<br />
C<br />
=<br />
=<br />
=<br />
=<br />
G thread connection type<br />
G thread connection type (based on JIS B2351 0 type)<br />
R thread connection type<br />
Gasket connection type<br />
Cartridge type (for in-line)<br />
Series number: <strong>10</strong><br />
C1M<br />
Type of hydraulic oil<br />
(Specify only in the case of gasket connection type.)<br />
No symbol = Mineral based hydraulic oil<br />
V = Phosphate ester based hydraulic oil<br />
W = Fatty ester based hydraulic oil<br />
Water-glycol based hydraulic oil<br />
(Note) It is not necessary to enter the type of<br />
hydraulic oil when the connection method is<br />
other than “P”.<br />
Cracking pressure<br />
00 = No spring<br />
(There is no no-spring type in the case of cartridge type.)<br />
01=<br />
0.01MPa(0.1kgf/cm 2 )<br />
05=<br />
0.05MPa(0.5kgf/cm 2 )<br />
15=<br />
0.15MPa(1.5kgf/cm 2 )<br />
30=<br />
0.29MPa(3.0kgf/cm 2 )<br />
40=<br />
0.39MPa(4.0kgf/cm 2 )<br />
Cartridge type check valve for angle<br />
Nominal dimension<br />
6, 8, <strong>10</strong>, 15, 20, 25, 30<br />
Connection method<br />
C = Cartridge type<br />
Series number: <strong>10</strong><br />
Type of hydraulic oil<br />
No symbol = Mineral based hydraulic oil<br />
Phosphate ester based hydraulic oil<br />
Fatty ester based hydraulic oil<br />
Water-glycol based hydraulic oil<br />
Cracking pressure<br />
01=<br />
0.01MPa(0.1kgf/cm 2 )<br />
05=<br />
0.05MPa(0.5kgf/cm 2 )<br />
15=<br />
0.15MPa(1.5kgf/cm 2 )<br />
30=<br />
0.29MPa(3.0kgf/cm 2 )<br />
40=<br />
0.39MPa(4.0kgf/cm 2 )<br />
1-65