DH6/10
DH6/10 DH6/10
Current - Pressure characteristics (viscosity 25 mm 2 /s (cSt)) PRDP6-10/30 PRDP6-10/50 Pressure (MPa) Pressure (MPa) Load pressure – Flow rate characteristics (viscosity 25 mm 2 /s (cSt)) Pressure (MPa) PRDP6-10/30 Current (mA) Primary pressure: 3.9 MPa (40 kgf/cm 2 ) Load flow rate: 0 L /min Dither: 60 Hz, 150 mAP-P Pressure (MPa) Current (mA) Primary pressure: 5.9 MPa (60 kgf/cm 2) Load flow rate: 0 L /min Dither: 60 Hz, 150 mAP-P PRDP6-10/50 Solenoid proportional pilot pressure reducing valve – Direct operated type Flow rate (L/min) Flow rate (L/min) Primary pressure: 3.9 MPa (40 kgf/cm 2 Dither: 60 Hz, 150 mAP-P Primary pressure: 5.9 MPa (60 kgf/cm 2) Dither: 60 Hz, 150 mAP-P Step response characteristics (viscosity 25 mm 2 /s (cSt)) PRDP6-10/30 Pressure (MPa) Current ( mA) Primary pressure: 13.7 MPa (140 kgf/cm 2 ) Secondary piping capacity: 15 cm 3 Load flow rate: 0 L / min Dither: 60 Hz, 150 mAP-P 6-11
■Dimension drawing ●PRDP6P Sure plug (170020-2 Made by AMP) JIS D5403 CA10 or equivalent Air bleeding plug 70 Section J 1 (Slit width) (Slit depth 1) Solenoid proportional pilot pressure reducing valve – Direct operated type O-ring・・・3-AS568 No.012 Hs90 (For ports P, A, and T) ±0.1 MAX.170 31 A 3-φ5.5 3-φ12.2 79 19 ±0.1 27.8 ±0.1 12.5 40.5 ±0.1 T P 9 27 0.75 ±0.1 48 5.95 ±0.1 8 MAX.70 16.25 ±0.1 ±0.1 26.55 ●PRDP6G 12.5 40.5 ±0.2 Section J 70 9 27 48 ±0.1 32.5 Section J: Details of the slit at the end of the screw 4-M5-50 Tightening torque:6.9±1.0 N・m (70±10.5 kgf・cm) 46 4-M6 (From the other side) Screw depth 10 MAX.66 ±0.2 31 7 T P A 13 ±0.2 32.5 46 15゚ PF1/8 1.6 +0.5 φ18 0 +0.1 φ11.6 0 45゚ 10.5 0.5 3.2 Section G Section G : Details of connection ports (P, A, T) 45 36 79 29 1 (Slit width) (Slit depth 1) MAX.170 Sure plug (170020-2 Made by AMP) JIS D5403 CA10 or equivalent Section J: Details of the slit at the end of the screw T P A Air bleeding plug 6-12
- Page 214 and 215: ●S-(2)TC22 5.6 29.2 100.6 94.3 76
- Page 216 and 217: ■Dimension drawing ●S-4C5 60 48
- Page 218 and 219: Check valve block ZA Hydraulic
- Page 220 and 221: ●ZA30 5 208.5 116 2 82.5 51.3 50.
- Page 222 and 223: Dimension drawing ZNS5-1 4-5.5 thro
- Page 224 and 225: ZNS10-1 4-6.6 through hole
- Page 226 and 227: Logic valve Logic valve KLD/LU A po
- Page 228 and 229: Logic valve Cover type symbols Nomi
- Page 230 and 231: Logic valve Pressure decreasing cha
- Page 232 and 233: Logic valve KLD - manifold Machinin
- Page 234 and 235: Logic valve 16 LU 25B
- Page 236 and 237: Logic valve LU 25 A 32DB Hydr
- Page 238 and 239: Logic valve LU40S Hydraulic symbo
- Page 240 and 241: Logic valve LU40E A B
- Page 242 and 243: Logic valve LU 50 63B O-ring “V
- Page 244 and 245: Logic valve 50 ●LU E 63 A L D E G
- Page 246 and 247: Logic valve LU80B Counterboring d
- Page 248 and 249: Logic valve LU 80 100 E A B
- Page 250 and 251: Selector valve Dimension drawing CS
- Page 252 and 253: Logic element for pressure control
- Page 254 and 255: Solenoid proportional control valve
- Page 256 and 257: ■Specifications Nominal dimension
- Page 258 and 259: Solenoid proportional balanced pist
- Page 260 and 261: Pressure override characteristics (
- Page 262 and 263: ●RBP35P-10/*-E B C P 165 130 X T
- Page 266 and 267: Solenoid proportional pilot pressur
- Page 268 and 269: ■Dimension drawing ●PRDP1M6-D 4
- Page 270 and 271: Specifications Nominal dimension
- Page 272 and 273: ■Dimension drawing 10 ●PRBP 20
- Page 274 and 275: ■Current - Flow rate characterist
- Page 276 and 277: Specifications Maximum working pres
- Page 278 and 279: ●DHP22 (Single solenoid type) 94.
- Page 280 and 281: Specifications Nominal dimension 6
- Page 282 and 283: Solenoid proportional control valve
- Page 284 and 285: ■Dimension drawing ●DHPL16 18.3
- Page 286 and 287: Type indication C series Controller
- Page 288 and 289: For AC power supply double solenoid
- Page 290 and 291: For DC power supply double solenoid
- Page 292 and 293: For DC power supply double solenoid
- Page 294 and 295: Sub-plate Appendix-1
- Page 296 and 297: ●Pressure control valve ●Flow c
- Page 298 and 299: ●P-RB10 Counterboring diameter φ
- Page 300 and 301: ●P-CHY20 Screw diameter J, screw
- Page 302 and 303: ●P-DE10 115 11.5 92 32 46 23 75 2
- Page 304 and 305: P-DEH16 Counterborin
- Page 306 and 307: ●P-PU20 Counterboring diameterφC
- Page 308 and 309: FlangeNipple Appendix-15
- Page 310 and 311: ●STNL-High pressure 30.9 MPa (315
- Page 312 and 313: Application examples of SUN cartrid
■Dimension drawing<br />
●PRDP6P<br />
Sure plug (170020-2 Made by AMP)<br />
JIS D5403 CA<strong>10</strong> or equivalent<br />
Air bleeding plug<br />
70<br />
Section J<br />
1 (Slit width)<br />
(Slit depth 1)<br />
Solenoid proportional pilot pressure reducing valve – Direct operated type<br />
O-ring・・・3-AS568 No.012 Hs90<br />
(For ports P, A, and T)<br />
±0.1<br />
MAX.170<br />
31<br />
A<br />
3-φ5.5<br />
3-φ12.2<br />
79<br />
19 ±0.1<br />
27.8 ±0.1<br />
12.5 40.5 ±0.1<br />
T<br />
P<br />
9<br />
27<br />
0.75 ±0.1<br />
48<br />
5.95 ±0.1<br />
8 MAX.70<br />
16.25 ±0.1<br />
±0.1<br />
26.55<br />
●PRDP6G<br />
12.5<br />
40.5 ±0.2<br />
Section J<br />
70<br />
9<br />
27<br />
48<br />
±0.1<br />
32.5<br />
Section J: Details of the slit at the end of the screw<br />
4-M5-50<br />
Tightening torque:6.9±1.0 N・m<br />
(70±<strong>10</strong>.5 kgf・cm)<br />
46<br />
4-M6 (From the other side)<br />
Screw depth <strong>10</strong><br />
MAX.66<br />
±0.2<br />
31<br />
7<br />
T<br />
P<br />
A<br />
13<br />
±0.2<br />
32.5<br />
46<br />
15゚<br />
PF1/8<br />
1.6<br />
+0.5<br />
φ18 0<br />
+0.1<br />
φ11.6 0<br />
45゚<br />
<strong>10</strong>.5 0.5<br />
3.2<br />
Section G<br />
Section G : Details of connection ports (P, A, T)<br />
45<br />
36<br />
79<br />
29<br />
1 (Slit width)<br />
(Slit depth 1)<br />
MAX.170<br />
Sure plug (170020-2 Made by AMP)<br />
JIS D5403 CA<strong>10</strong> or equivalent<br />
Section J: Details of the slit at the end of the screw<br />
T<br />
P<br />
A<br />
Air bleeding plug<br />
6-12
Change language