DH6/10
DH6/10 DH6/10
Logic valve Pressure decreasing characteristics (Viscosity 36 mm 2 /s (cSt)) Decreasing amount of pressure Flow rate (L/min) With cushion overlap Without cushion overlap Decreasing amount of pressure In case of no spring Flow rate (L/min) Decreasing amount of pressure Flow rate (L/min) Decreasing amount of pressure Flow rate (L/min) Pressure – Flow rate characteristics (Viscosity 36 mm 2 /s (cSt)) Restriction contraction hole diameter (mm) Flow rate (L/min) 5-6
Dimension drawing KLD Type ** Without cushion overlap ** With cushion overlap ** Without cushion overlap ** With cushion overlap Logic valve Hydraulic symbols Single shim thickness Single shim thickness Nominal dimension Selecting procedure of a shim 1. Three types of shims with different thickness are attached. 2. Select one shim out of the three and assemble it to the manifold or block. Assemble them so as the gap between the bushing and manifold to be 0 to 50μ. Manifold Bushing Shim 5-7
- Page 180 and 181: Three-way flow regulating valve
- Page 182 and 183: ■Dimension drawing ●FK10 6 10 9
- Page 184 and 185: Check valve S-(2)C Type indicat
- Page 186 and 187: ■Dimension drawing ●S-(2)C6 2 T
- Page 188 and 189: Specifications Nominal dimension Ma
- Page 190 and 191: ●S-(2)CH16 4-φ11 through hole 76
- Page 192 and 193: Relief valve Specifications Nominal
- Page 194 and 195: Sequence valve - Direct operated ty
- Page 196 and 197: ■Dimension drawing ●S-SD6-10-P
- Page 198 and 199: Pressure reducing valve - Direct op
- Page 200 and 201: ■Dimension drawing ●S-PRD6-10-P
- Page 202 and 203: Throttle valve S-(2)T Type
- Page 204 and 205: ■Dimension drawing ●S-T6-10-P 4
- Page 206 and 207: ●S-T10-10-P 46 39.7 16 4-φ6.6 th
- Page 208 and 209: Slow return check valve S-(2)TC
- Page 210 and 211: Opening - Flow rate characteristics
- Page 212 and 213: Dimension drawing S-2TC6 Maximum 21
- Page 214 and 215: ●S-(2)TC22 5.6 29.2 100.6 94.3 76
- Page 216 and 217: ■Dimension drawing ●S-4C5 60 48
- Page 218 and 219: Check valve block ZA Hydraulic
- Page 220 and 221: ●ZA30 5 208.5 116 2 82.5 51.3 50.
- Page 222 and 223: Dimension drawing ZNS5-1 4-5.5 thro
- Page 224 and 225: ZNS10-1 4-6.6 through hole
- Page 226 and 227: Logic valve Logic valve KLD/LU A po
- Page 228 and 229: Logic valve Cover type symbols Nomi
- Page 232 and 233: Logic valve KLD - manifold Machinin
- Page 234 and 235: Logic valve 16 LU 25B
- Page 236 and 237: Logic valve LU 25 A 32DB Hydr
- Page 238 and 239: Logic valve LU40S Hydraulic symbo
- Page 240 and 241: Logic valve LU40E A B
- Page 242 and 243: Logic valve LU 50 63B O-ring “V
- Page 244 and 245: Logic valve 50 ●LU E 63 A L D E G
- Page 246 and 247: Logic valve LU80B Counterboring d
- Page 248 and 249: Logic valve LU 80 100 E A B
- Page 250 and 251: Selector valve Dimension drawing CS
- Page 252 and 253: Logic element for pressure control
- Page 254 and 255: Solenoid proportional control valve
- Page 256 and 257: ■Specifications Nominal dimension
- Page 258 and 259: Solenoid proportional balanced pist
- Page 260 and 261: Pressure override characteristics (
- Page 262 and 263: ●RBP35P-10/*-E B C P 165 130 X T
- Page 264 and 265: Current - Pressure characteristics
- Page 266 and 267: Solenoid proportional pilot pressur
- Page 268 and 269: ■Dimension drawing ●PRDP1M6-D 4
- Page 270 and 271: Specifications Nominal dimension
- Page 272 and 273: ■Dimension drawing 10 ●PRBP 20
- Page 274 and 275: ■Current - Flow rate characterist
- Page 276 and 277: Specifications Maximum working pres
- Page 278 and 279: ●DHP22 (Single solenoid type) 94.
Dimension drawing<br />
KLD<br />
Type<br />
**<br />
Without cushion overlap<br />
**<br />
With cushion overlap<br />
**<br />
Without cushion overlap<br />
**<br />
With cushion overlap<br />
Logic valve<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Hydraulic symbols<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Single shim thickness<br />
<br />
<br />
Single shim thickness<br />
<br />
<br />
Nominal dimension<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Selecting procedure of a shim<br />
1. Three types of shims with different thickness are attached.<br />
2. Select one shim out of the three and assemble it to the manifold or block.<br />
Assemble them so as the gap between the bushing and manifold to be 0 to 50μ.<br />
Manifold<br />
<br />
Bushing <br />
Shim<br />
5-7
Change language