DH6/10
DH6/10 DH6/10
Throttle valve S-(2)T Type indication Sandwich type Throttle valve T = Single type 2T = Double type Nominal dimension 6, 10 Series number: 10 Type of hydraulic oil No symbol Mineral based hydraulic oil V Phosphate ester based hydraulic oil W Fatty ester based hydraulic oil Water-glycol based hydraulic oil Shape of adjustment part 4 = Thread adjustment (without cap) Throttle valve incorporated port symbol Symbol Incorporated port T 2T A B P E Port A Port B Port P Port A, B Hydraulic symbols Throttle valve (Note) P1, A1, B1 and T1 show ports on the sub-plate side while P, A, B and T show ports on the selector valve side. 4-20
Specifications Nominal dimension Maximum working pressure MPa (kgf/cm 2 ) 30.9 (315) Maximum flow rate L/min 30 70 Mass kg 1.0 1.7 Mounting bolt Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm 2 ) S-(2)T6 S-(2)T10 M570L M670L 4 pcs. 4 pcs. 6.40.5 (5 5) 13 1 (13310) When the solenoid valve is 10 Series, mounting bolts are as shown in the table below. Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm 2 ) S-(2)T6 M575L 4 pcs. 7.40.5 (75 5) S-(2)T10 M685L 4 pcs. 11.81.7 (12018) Pressure drop characteristics (viscosity 36 mm 2 /s (cSt)) When the throttle valve is fully open Pressure drop amount (MPa) Throttle valve Flow rate (L/min) 4-21
- Page 152 and 153: Pressure drop characteristics (visc
- Page 154 and 155: Variable throttle valve T1M 3-2 Th
- Page 156 and 157: ■Dimension drawing ●T1M*P C (wh
- Page 158 and 159: ■Pressure - Flow rate characteris
- Page 160 and 161: ■Dimension drawing ●T1M*P L1 L2
- Page 162 and 163: ■Pressure - Flow rate characteris
- Page 164 and 165: ■Pressure drop characteristics (v
- Page 166 and 167: 3-13 ■Dimension drawing ●TC1M*P
- Page 168 and 169: Pressure - Flow rate characteristic
- Page 170 and 171: ■Pressure drop characteristics (v
- Page 172 and 173: Pressure - Flow rate characteristic
- Page 174 and 175: 8 ●F*G/R 4-φ5.5 through hole Cou
- Page 176 and 177: Specifications Nominal dimension Ma
- Page 178 and 179: Temperature and pressure compensate
- Page 180 and 181: Three-way flow regulating valve
- Page 182 and 183: ■Dimension drawing ●FK10 6 10 9
- Page 184 and 185: Check valve S-(2)C Type indicat
- Page 186 and 187: ■Dimension drawing ●S-(2)C6 2 T
- Page 188 and 189: Specifications Nominal dimension Ma
- Page 190 and 191: ●S-(2)CH16 4-φ11 through hole 76
- Page 192 and 193: Relief valve Specifications Nominal
- Page 194 and 195: Sequence valve - Direct operated ty
- Page 196 and 197: ■Dimension drawing ●S-SD6-10-P
- Page 198 and 199: Pressure reducing valve - Direct op
- Page 200 and 201: ■Dimension drawing ●S-PRD6-10-P
- Page 204 and 205: ■Dimension drawing ●S-T6-10-P 4
- Page 206 and 207: ●S-T10-10-P 46 39.7 16 4-φ6.6 th
- Page 208 and 209: Slow return check valve S-(2)TC
- Page 210 and 211: Opening - Flow rate characteristics
- Page 212 and 213: Dimension drawing S-2TC6 Maximum 21
- Page 214 and 215: ●S-(2)TC22 5.6 29.2 100.6 94.3 76
- Page 216 and 217: ■Dimension drawing ●S-4C5 60 48
- Page 218 and 219: Check valve block ZA Hydraulic
- Page 220 and 221: ●ZA30 5 208.5 116 2 82.5 51.3 50.
- Page 222 and 223: Dimension drawing ZNS5-1 4-5.5 thro
- Page 224 and 225: ZNS10-1 4-6.6 through hole
- Page 226 and 227: Logic valve Logic valve KLD/LU A po
- Page 228 and 229: Logic valve Cover type symbols Nomi
- Page 230 and 231: Logic valve Pressure decreasing cha
- Page 232 and 233: Logic valve KLD - manifold Machinin
- Page 234 and 235: Logic valve 16 LU 25B
- Page 236 and 237: Logic valve LU 25 A 32DB Hydr
- Page 238 and 239: Logic valve LU40S Hydraulic symbo
- Page 240 and 241: Logic valve LU40E A B
- Page 242 and 243: Logic valve LU 50 63B O-ring “V
- Page 244 and 245: Logic valve 50 ●LU E 63 A L D E G
- Page 246 and 247: Logic valve LU80B Counterboring d
- Page 248 and 249: Logic valve LU 80 100 E A B
- Page 250 and 251: Selector valve Dimension drawing CS
Throttle valve<br />
S-(2)T<br />
<br />
<br />
<br />
Type indication<br />
Sandwich type<br />
Throttle valve<br />
T = Single type<br />
2T = Double type<br />
Nominal dimension<br />
6, <strong>10</strong><br />
Series number: <strong>10</strong><br />
Type of hydraulic oil<br />
No symbol Mineral based hydraulic oil<br />
V Phosphate ester based hydraulic oil<br />
W Fatty ester based hydraulic oil<br />
Water-glycol based hydraulic oil<br />
Shape of adjustment part<br />
4 = Thread adjustment (without cap)<br />
Throttle valve incorporated port symbol<br />
Symbol Incorporated port<br />
T<br />
2T<br />
A<br />
B<br />
P<br />
E<br />
Port A<br />
Port B<br />
Port P<br />
Port A, B<br />
Hydraulic symbols<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Throttle valve<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
(Note) P1, A1, B1 and T1 show ports on the sub-plate side while P, A, B and T show ports on the selector valve side.<br />
4-20
Change language