DH6/10
DH6/10 DH6/10
Check valve S-(2)C Type indication Sandwich type Check valve C = Single type 2C = Double type Nominal dimension 6, 10 Series number: 11 Specifications Nominal dimension 6 10 Maximum working pressure MPa (kgf/cm 2 ) 30.9 (315) Maximum flow rate L/min Cracking pressure MPa (kgf/cm 2 ) Mass kg 40 100 0.05 (0.5) 0.9 2.4 Type of hydraulic oil No symbol Mineral based hydraulic oil V Phosphate ester based hydraulic oil W Fatty ester based hydraulic oil Water-glycol based hydraulic oil Cracking pressure 05 = 0.05MPa (0.5kgf/cm 2 ) Check valve incorporated port symbol C 2C Symbol Check valve incorporated port T Port T P Port P A Port A B Port B C Port A D Port B Port A E Port B Direction of free flow T T1 P1 P A1 A B1 B A A1 B B1 A A1 B B1 Mounting bolt Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm 2 ) C6 C10 M585L M685L 4 pcs. 4 pcs. 6.40.5 655 13 1 (13310 When the solenoid valve is 10 Series, mounting bolts are as shown in the table below. Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm 2 ) Check valve Pressure drop characteristics (viscosity 36 mm 2 /s (cSt)) S-(2)C6 S-(2)C10 C6 M590L 4 pcs. 7.40.5 75 5 C10 M6100L 4 pcs. 11.8 1.712018 When the throttle valve is fully open and the check valve is free flow Pressure drop amount (MPa) Pressure drop amount (MPa) Flow rate (L/min) Flow rate (L/min) 4-2
Hydraulic symbols (Note) P1, A1, B1 and T1 show ports on the sub-plate side while P, A, B and T show ports on the selector valve side. Check valve 4-3
- Page 134 and 135: Dimension drawing SB L5 L3 L2 6 13
- Page 136 and 137: Pressure override characteristics (
- Page 138 and 139: Pressure reducing valve - Balanced
- Page 140 and 141: Secondary side minimum adjustment p
- Page 142 and 143: The direct operated type relief val
- Page 144 and 145: ●B*G/GT*・3 ●Handle adjusting
- Page 146 and 147: ●B*P*・1 ●Handle adjusting typ
- Page 148 and 149: Counterbalance valve CBD Overview
- Page 150 and 151: Dimension drawing CBD*G/R Handle ad
- Page 152 and 153: Pressure drop characteristics (visc
- Page 154 and 155: Variable throttle valve T1M 3-2 Th
- Page 156 and 157: ■Dimension drawing ●T1M*P C (wh
- Page 158 and 159: ■Pressure - Flow rate characteris
- Page 160 and 161: ■Dimension drawing ●T1M*P L1 L2
- Page 162 and 163: ■Pressure - Flow rate characteris
- Page 164 and 165: ■Pressure drop characteristics (v
- Page 166 and 167: 3-13 ■Dimension drawing ●TC1M*P
- Page 168 and 169: Pressure - Flow rate characteristic
- Page 170 and 171: ■Pressure drop characteristics (v
- Page 172 and 173: Pressure - Flow rate characteristic
- Page 174 and 175: 8 ●F*G/R 4-φ5.5 through hole Cou
- Page 176 and 177: Specifications Nominal dimension Ma
- Page 178 and 179: Temperature and pressure compensate
- Page 180 and 181: Three-way flow regulating valve
- Page 182 and 183: ■Dimension drawing ●FK10 6 10 9
- Page 186 and 187: ■Dimension drawing ●S-(2)C6 2 T
- Page 188 and 189: Specifications Nominal dimension Ma
- Page 190 and 191: ●S-(2)CH16 4-φ11 through hole 76
- Page 192 and 193: Relief valve Specifications Nominal
- Page 194 and 195: Sequence valve - Direct operated ty
- Page 196 and 197: ■Dimension drawing ●S-SD6-10-P
- Page 198 and 199: Pressure reducing valve - Direct op
- Page 200 and 201: ■Dimension drawing ●S-PRD6-10-P
- Page 202 and 203: Throttle valve S-(2)T Type
- Page 204 and 205: ■Dimension drawing ●S-T6-10-P 4
- Page 206 and 207: ●S-T10-10-P 46 39.7 16 4-φ6.6 th
- Page 208 and 209: Slow return check valve S-(2)TC
- Page 210 and 211: Opening - Flow rate characteristics
- Page 212 and 213: Dimension drawing S-2TC6 Maximum 21
- Page 214 and 215: ●S-(2)TC22 5.6 29.2 100.6 94.3 76
- Page 216 and 217: ■Dimension drawing ●S-4C5 60 48
- Page 218 and 219: Check valve block ZA Hydraulic
- Page 220 and 221: ●ZA30 5 208.5 116 2 82.5 51.3 50.
- Page 222 and 223: Dimension drawing ZNS5-1 4-5.5 thro
- Page 224 and 225: ZNS10-1 4-6.6 through hole
- Page 226 and 227: Logic valve Logic valve KLD/LU A po
- Page 228 and 229: Logic valve Cover type symbols Nomi
- Page 230 and 231: Logic valve Pressure decreasing cha
- Page 232 and 233: Logic valve KLD - manifold Machinin
Check valve<br />
S-(2)C<br />
<br />
<br />
<br />
<br />
Type indication<br />
Sandwich type<br />
Check valve<br />
C = Single type<br />
2C = Double type<br />
Nominal dimension<br />
6, <strong>10</strong><br />
Series number: 11<br />
Specifications<br />
Nominal dimension 6 <strong>10</strong><br />
Maximum working pressure MPa (kgf/cm 2 )<br />
30.9 (315)<br />
Maximum flow rate L/min<br />
Cracking pressure MPa (kgf/cm 2 )<br />
Mass kg<br />
40 <strong>10</strong>0<br />
0.05 (0.5)<br />
0.9 2.4<br />
Type of hydraulic oil<br />
No symbol<br />
Mineral based hydraulic oil<br />
V Phosphate ester based hydraulic oil<br />
W Fatty ester based hydraulic oil<br />
Water-glycol based hydraulic oil<br />
Cracking pressure<br />
05 = 0.05MPa (0.5kgf/cm 2 )<br />
Check valve incorporated port symbol<br />
C<br />
2C<br />
Symbol Check valve incorporated port<br />
T Port T<br />
P Port P<br />
A Port A<br />
B Port B<br />
C Port A<br />
D Port B<br />
Port A<br />
E<br />
Port B<br />
Direction of free flow<br />
T T1<br />
P1 P<br />
A1 A<br />
B1 B<br />
A A1<br />
B B1<br />
A A1<br />
B B1<br />
Mounting bolt<br />
Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm 2 )<br />
C6<br />
C<strong>10</strong><br />
M585L<br />
M685L<br />
4 pcs.<br />
4 pcs.<br />
6.40.5 655<br />
13 1 (133<strong>10</strong><br />
When the solenoid valve is <strong>10</strong> Series, mounting bolts are as shown in the table below.<br />
Type Hexagon socket head cap thread Quantity Tightening torque Nm (kgfcm 2 )<br />
Check valve<br />
Pressure drop characteristics (viscosity 36 mm 2 /s (cSt))<br />
S-(2)C6<br />
S-(2)C<strong>10</strong><br />
C6<br />
M590L<br />
4 pcs. 7.40.5 75 5<br />
C<strong>10</strong><br />
M6<strong>10</strong>0L 4 pcs. 11.8 1.712018<br />
When the throttle valve is fully open and the check valve is free flow<br />
Pressure drop amount (MPa)<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Pressure drop amount (MPa)<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Flow rate (L/min)<br />
Flow rate (L/min)<br />
4-2