CAN 2.0A/B â RS232/RS485 Converter
CAN 2.0A/B â RS232/RS485 Converter CAN 2.0A/B â RS232/RS485 Converter
Befehl I Ixxx(CR) or Ixxxxxxxx(CR) Funktion Identifier in Hex (000...7FF) 11 Bit Standard Format or Identifier in Hex (00000000...1FFFFFFF) 29 Bit Extended Format L Lx(CR) Listen Mode Only (0...1) This setting determines whether only 11-bit or 11-bit and 29-bit are accepted by CAN-Acceptance-Code and CAN-Acceptance-Mask. Response: “List of parameters: (CR)OK(CR)” or “ERROR(CR)“ 0 – CAN Normal Mode (read and write) 1 – CAN Listen Only Mode (listening only, read) Response: “List of parameters: (CR)OK(CR)” or “ERROR(CR)“ A Axxxxxxxx(CR) CAN-Acceptance-Code x = (0...000007FF) 11 Bit Standard Format CAN-Acceptance-Code x = (0...1FFFFFFF) 29 Bit Extended Format x = 0 receives all CAN-Frames Response: “List of parameters: (CR)OK(CR)” or “ERROR(CR)“ M Mxxxxxxxx(CR) CAN-Acceptance-Mask x = (0..000007FF) 11 Bit Standard Format CAN-Acceptance-Mask x = (0..1FFFFFFF) 29 Bit Extended Format R V N R0(CR) R1(CR) R2(CR) R3(CR) R4(CR) R5(CR) R6(CR) R7(CR) R8(CR) R9(CR) RA(CR) RB(CR) RC(CR) RD(CR) RE(CR) RF(CR) x = F receives all CAN-Frames Response: “List of parameters: (CR)OK(CR)” or “ERROR(CR)“ 600 bps RS232/RS485 Baudrate (all 8 N 1) 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps 230000 bps 500000 bps 600000 bps 750000 bps 1000000 bps 1500000 bps 3000000 bps Other baud rates available on request Response: “ (CR)OK(CR)” or “ERROR(CR)” Software Version Number Response: „Software Version: x.x(CR)“ Converter Nummer x = 0..F Response: „Converter-ID: xxxx xxxx(CR)“ x= 0..F
Befehl ? or H ? or H Funktion Help This table is output to the COM port E E Exit Exits the Setup Mode and saves the configuration in flash memory of the converter, followed by a Reset = Power On(Restart) Response: e.g. C CAN-Bitrate : 5 L CAN-Data Length : 8 I CAN-Identifier : 1F0000000 A CAN-Acceptance-Code : 00000100 M CAN-Acceptance-Mask : 00000000 R USB-Baudrate : 3 Identifier Length : 29 Acc. Code Length : 32 Acc. Mask Length : 32 SAVE to EEprom OK RESET Q Q Quit Exits the setup mode WITHOUT saving changes in the in flash memory of the converter, followed by a Reset = Power On(Restart) Response: OK RESET Other parameters, functions are available on request.
- Page 1 and 2: CAN 2.0A/B ↔ RS232/RS485 Converte
- Page 3 and 4: 1 Introduction As a powerful tool t
- Page 6 and 7: 4.1 CAN ID Filter Setup The convert
- Page 8 and 9: 5.2 Receiving Data What data receiv
- Page 12 and 13: 7 Technical Specifications: CAN ↔
- Page 14: UL recognition: 5000 V rms for 1 mi
Befehl<br />
?<br />
or<br />
H<br />
?<br />
or<br />
H<br />
Funktion<br />
Help<br />
This table is output to the COM port<br />
E E Exit<br />
Exits the Setup Mode and saves the configuration in flash memory of the<br />
converter, followed by a Reset = Power On(Restart)<br />
Response: e.g.<br />
C <strong>CAN</strong>-Bitrate : 5<br />
L <strong>CAN</strong>-Data Length : 8<br />
I <strong>CAN</strong>-Identifier : 1F0000000<br />
A <strong>CAN</strong>-Acceptance-Code : 00000100<br />
M <strong>CAN</strong>-Acceptance-Mask : 00000000<br />
R USB-Baudrate : 3<br />
Identifier Length : 29<br />
Acc. Code Length : 32<br />
Acc. Mask Length : 32<br />
SAVE to EEprom<br />
OK<br />
RESET<br />
Q Q Quit<br />
Exits the setup mode WITHOUT saving changes in the in flash memory of<br />
the converter, followed by a Reset = Power On(Restart)<br />
Response:<br />
OK<br />
RESET<br />
Other parameters, functions are available on request.