33 12 16.26 - 001-A - Response AAN-ANR Butterfly Valves - Garney ...
33 12 16.26 - 001-A - Response AAN-ANR Butterfly Valves - Garney ... 33 12 16.26 - 001-A - Response AAN-ANR Butterfly Valves - Garney ...
9.13 Option Interrupter Timer Setting instructions for actuator including an interrupter timer. The interrupter timer enables pulsed “stop/start” operation by the actuator as a response to local and remote control commands. This effectively increases the valve stroke time and can be adjusted to prevent hydraulic shock (water hammer) and flow surges in pipelines. The interrupter timer is an optional extra – check wiring diagram for inclusion. OJ Interrupter Timer Enabled/Disabled When fitted, the timer will be made available for operation. The Interrupter cannot be enabled or disabled using the Setting Tool. Interrupter Timer Interrupter Timer Disabled Enabled When the timer option is available an additional series of settings can be accessed by pressing the ◗ key. NOTE: If the timer option is not available pressing the ◗ key will not access setting. Press the ◗ key to display interrupter timer set-up screens. Jd Interrupter Timer Direction The default for timer direction is [CL], timer operation will start in closing and stop in opening – pulsing operation around the close position. If pulsing operation is required to stop in closing and start in opening – around the open position, use the + or - key. The display will change to [OP]. PRESS THE KEY. The displayed option will flash indicating that it has been set. Pulsed Operation Around the Closed Position NOTE: Instructions [JC] and [JO] are for timer operation around the Closed position. For timing around the Open position, read stop for start [JC] and start for stop [JO]. Press the ❖ key to display [JC]. JC 60 Position in Valve Closing Stroke for Timer to Start Using the + or - key select the position for the TIMER TO START WHEN THE VALVE IS CLOSING. [ ][] = valve closed [00] to [99] = percentage open [ ] = valve open Timer Set to Start Pulsing when Closing Valve Reaches 25% Open PRESS THE KEY. The displayed option will flash indicating that it has been set. If the timing is not required in the closing stroke select [JC] to [ ][] valve closed position. Press the ❖ key to display [JO].
JO Position in Valve Opening Stroke for Timer to Stop Jn Contactor On Time Contactor Off Time JF JE ESD Override Interrupter Timer 61 Using the + or - key select the position for the TIMER TO STOP WHEN THE VALVE IS OPENING. [ ][] = valve closed [00] to [99] = percentage open [ ] = valve open Timer Set to Stop Pulsing when Opening Valve Reaches 25% Open PRESS THE KEY. The displayed option will flash indicating that it has been set. If timing is not required in the opening stroke select [JO] to [ ][]. Press the ❖ key to display [Jn]. Using the + or - key select the actuator run period in the range 1–99 seconds. Actuator Run Period Set for 5 Seconds PRESS THE KEY. The displayed option will flash indicating that it has been set. Press the ❖ key to display [JF]. Using the + or - key select the actuator stop period in the range 1–99 seconds. Actuator OFF Period Set for 25 Seconds PRESS THE KEY. The displayed option will flash indicating that it has been set. Press the ❖ key to display [JE] (refer to note on Page 62). The interrupter timer may be overridden when the actuator is under ESD signal command. This will mean the actuator will run to limit without “stop/start” action under ESD command. Refer to A1–A3 (refer to page 34 for ESD settings). The default for ESD override interrupter timer is [OF]. The interrupter timer will continue “stop/start” action during ESD action. If ESD must override the timer use the + or - to display [On]. ESD Override Timer OFF PRESS THE KEY. The displayed option will flash indicating that it has been set.
- Page 355 and 356: 9 Fig. 4.9 Type A Drive Bush in Pos
- Page 357 and 358: 11 5.1 Rising Stem Valves - Top Mou
- Page 359 and 360: 13 5.7 IQML Adjusting Linear Stroke
- Page 361 and 362: 15 6.4 Connecting to Terminals On E
- Page 363 and 364: 17 7.2 The Setting Tool Specificati
- Page 365 and 366: 19 7.7 Procedure Branch - Crossroad
- Page 367 and 368: 21 Viewing the Primary Function Set
- Page 369 and 370: C2 Close Action 23 The actuator can
- Page 371 and 372: tC Torque Value Closing 25 The valu
- Page 373 and 374: LC Set Limit Closed LO Set Limit Op
- Page 375 and 376: Fig. 9 9 Commissioning - Secondary
- Page 377 and 378: SECONDARY FUNCTIONS CONTENTS page 9
- Page 379 and 380: 1 Contact S1 - Value r1 Contact S1
- Page 381 and 382: A4 ESD Override Interlocks A5 ESD O
- Page 383 and 384: 9.4 Option Extra Indication Contact
- Page 385 and 386: 9.6 Option Folomatic Remote Control
- Page 387 and 388: Fd Deadband Adjustment Ft Motion In
- Page 389 and 390: 9.8 Bus System Option Pakscan [OP]
- Page 391 and 392: PF Pakscan Remote Auxiliary Input 4
- Page 393 and 394: 9.9 Bus System Option Modbus [OP] P
- Page 395 and 396: PF Modbus Remote Auxiliary Input PP
- Page 397 and 398: 9.10 Bus System Option Profibus DP
- Page 399 and 400: PF Profibus Remote Auxiliary Input
- Page 401 and 402: 9.11 Option DeviceNet PA DeviceNet
- Page 403 and 404: PF DeviceNet Remote Auxiliary Input
- Page 405: Fd Bus System Deadband Adjustment A
- Page 409 and 410: 9.16 Default Options [d1] and [d2]
- Page 411 and 412: 10 Maintenance, Monitoring and Trou
- Page 413 and 414: 10 Maintenance, Monitoring and Trou
- Page 415 and 416: H3 Factors Inhibiting Electrical Op
- Page 417 and 418: H6 Torque Switch Status & IR Settin
- Page 419 and 420: 10.2 IrDA Diagnostics & Config. IQ
- Page 421 and 422: BHD Binary, Hexadecimal and Decimal
- Page 423 and 424: If your Rotork actuator has been co
- Page 425 and 426: New Zealand Wellington Agent North
- Page 428: Heading ATTENTION: RED PLASTIC PLUG
9.13 Option<br />
Interrupter Timer<br />
Setting instructions for actuator<br />
including an interrupter timer.<br />
The interrupter timer enables pulsed<br />
“stop/start” operation by the actuator<br />
as a response to local and remote<br />
control commands.<br />
This effectively increases the valve<br />
stroke time and can be adjusted to<br />
prevent hydraulic shock (water<br />
hammer) and flow surges in pipelines.<br />
The interrupter timer is an optional<br />
extra – check wiring diagram for<br />
inclusion.<br />
OJ<br />
Interrupter Timer<br />
Enabled/Disabled<br />
When fitted, the timer will be<br />
made available for operation.<br />
The Interrupter cannot be<br />
enabled or disabled using the<br />
Setting Tool.<br />
Interrupter Timer Interrupter Timer<br />
Disabled Enabled<br />
When the timer option is available an<br />
additional series of settings can be<br />
accessed by pressing the ◗ key.<br />
NOTE: If the timer option is not<br />
available pressing the ◗ key will not<br />
access setting.<br />
Press the ◗ key to display interrupter<br />
timer set-up screens.<br />
Jd<br />
Interrupter Timer<br />
Direction<br />
The default for timer direction is [CL],<br />
timer operation will start in closing<br />
and stop in opening – pulsing<br />
operation around the close position.<br />
If pulsing operation is required to stop<br />
in closing and start in opening – around<br />
the open position, use the + or - key.<br />
The display will change to [OP].<br />
PRESS THE KEY.<br />
The displayed option will flash<br />
indicating that it has been set.<br />
Pulsed Operation Around the<br />
Closed Position<br />
NOTE: Instructions [JC] and [JO] are for<br />
timer operation around the Closed<br />
position. For timing around the Open<br />
position, read stop for start [JC] and<br />
start for stop [JO].<br />
Press the ❖ key to display [JC].<br />
JC<br />
60<br />
Position in Valve<br />
Closing Stroke for<br />
Timer to Start<br />
Using the + or - key select the position<br />
for the TIMER TO START WHEN THE<br />
VALVE IS CLOSING.<br />
[ ][] = valve closed<br />
[00] to [99] = percentage open<br />
[ ] = valve open<br />
Timer Set to Start Pulsing when<br />
Closing Valve Reaches 25% Open<br />
PRESS THE KEY.<br />
The displayed option will flash<br />
indicating that it has been set.<br />
If the timing is not required in the<br />
closing stroke select [JC] to [ ][] valve<br />
closed position.<br />
Press the ❖ key to display [JO].