33 12 16.26 - 001-A - Response AAN-ANR Butterfly Valves - Garney ...
33 12 16.26 - 001-A - Response AAN-ANR Butterfly Valves - Garney ... 33 12 16.26 - 001-A - Response AAN-ANR Butterfly Valves - Garney ...
24”-48” HP250II Butterfly Valve Functional Description Round butterfly valve discs rotate 1/4 turns to provide tight shutoff in air or water pipelines. The valves can be used to regulate flow rate by positioning the disc between 15 and 90 degrees open. Manually Operated Valve Manually operated butterfly valves are powered with gear actuators, which convert multiple handwheel, chainwheel or nut input turns into 1/4 turn valve operation. The travel of the valve disc is limited by physical stops in the actuator housing. WARNING Forcing the handwheel, chainwheel or nut against the stops will not provide tighter shutoff of the valve and may damage the actuator. Only actuator adjustments will affect valve shutoff. Motor Operated Valve Motor operated butterfly valves are powered with gear actuators, which convert multiple motor input turns into 1/4 turn valve operation. The travel of the valve disc is limited by limit switches in the motor housing and physical stops in the actuator housing. Valve shutoff is affected by limit switch and physical stop settings. WARNING Improperly set limit switches and/or physical stops may damage the motor and/or actuator. Cylinder Operate Valve Hydraulically operated butterfly valves are powered with a gear box and double acting cylinder. The linear stroke of the cylinder is converted to 1/4 turn operation by the gear box. Auxiliary controls are provided to direct hydraulic power to the cylinder and to control the operating speed of the cylinder. Document #: 2448HP250IIOM Revision Date: 1/10/11 4
24”-48” HP250II Butterfly Valve INSTALLATION GENERAL Valves are a significant component of any piping system. Failure due to faulty installation, improper operation or maintenance in such systems could result in damage, down time and costly repairs. In buried underground installations, problems or malfunctions can result in extensive, costly unearthing operations to correct the problem. Many problems with valves can be traced to improper installation, operation, or maintenance procedures. UNLOADING Inspect valves on receipt for damage in shipment and conformance with quantity and description in the shipping notice and order. Carefully unload all valves to the ground without dropping using fork trucks or slings under skids. Do not lift valves with slings or chain around operating shaft, actuator, or through waterway. Instead, lift valves with eye bolts or rods through flange holes. STORAGE Whenever practical, store valves indoors. If not, protect valves and actuators from weather and accumulation of water, dirt, rocks and debris. When valves fitted with power actuators and controls are stored, energize electric actuator or otherwise protect electrical control equipment to prevent corrosion of electrical contacts due to condensation resulting from temperature variation. Do not expose rubber seats to sunlight or ozone for any extended period. Valves should be stored with the valve disc or closure member slightly open. INSPECTION PRIOR TO INSTALLATION Make sure flange faces and joint sealing surfaces, body seats and disc seats are clean. Check bolting attaching actuator to valve for loosening in transit and handling. If loose, tighten firmly. Open and close valve to make sure it operates properly and that stops or limit switches are correctly set so that the valve seats fully. Check that valve rotation direction is correct and close valve before installing. INSTALLATION The following items must be performed during installation to ensure proper function. • Carefully place valves into position avoiding contact or impact with other equipment, vault walls or trench walls. Document #: 2448HP250IIOM Revision Date: 1/10/11 5
- Page 95 and 96: E-Lok Seat Design Years of Reliable
- Page 97 and 98: Water Flow Characteristics Proven P
- Page 99 and 100: Valve End Types and Dimensions: Mec
- Page 101 and 102: Actuation Traveling Nut Type Manual
- Page 103: 401 S. Highland Avenue Aurora, Illi
- Page 106 and 107: SCOPE OF THE LINE: PRATT HP250II B
- Page 108 and 109: THE HENRY PRATT SEAT ON BODY DESIGN
- Page 110 and 111: HP250II 3"- 20", DUCTILE IRON BODY
- Page 112 and 113: 401 S. Highland Avenue Aurora, Illi
- Page 114 and 115: Suggested Specification: Butterfly
- Page 116 and 117: 6" - 24" HP350 Mechanical Joint End
- Page 118 and 119: 3”-20” 2FII & Groundhog® Bonde
- Page 120 and 121: 3”-20” 2FII & Groundhog® Bonde
- Page 122 and 123: 3”-20” 2FII & Groundhog® Bonde
- Page 124 and 125: 3”-20” 2FII & Groundhog® Bonde
- Page 126 and 127: 3”-20” 2FII & Groundhog® Bonde
- Page 128 and 129: 3”-20” 2FII & Groundhog® Bonde
- Page 130 and 131: Triton XR-70,Triton XL & Groundhog
- Page 132 and 133: Triton XR-70,Triton XL & Groundhog
- Page 134 and 135: Triton XR-70,Triton XL & Groundhog
- Page 136 and 137: Triton XR-70,Triton XL & Groundhog
- Page 138 and 139: Triton XR-70,Triton XL & Groundhog
- Page 140 and 141: Triton XR-70,Triton XL & Groundhog
- Page 142 and 143: Triton XR-70,Triton XL & Groundhog
- Page 144 and 145: 24”-48” HP250II Butterfly Valve
- Page 148 and 149: 24”-48” HP250II Butterfly Valve
- Page 150 and 151: 24”-48” HP250II Butterfly Valve
- Page 152 and 153: 24”-48” HP250II Butterfly Valve
- Page 154 and 155: 24”-48” HP250II Butterfly Valve
- Page 156 and 157: HP350 Butterfly Valve 6”-24” (M
- Page 158 and 159: HP350 Butterfly Valve Table of Cont
- Page 160 and 161: HP350 Butterfly Valve INSTALLATION
- Page 162 and 163: HP350 Butterfly Valve TESTING When
- Page 164 and 165: HP350 Butterfly Valve WARNING Fluid
- Page 166 and 167: HP350 Butterfly Valve TROUBLESHOOTI
- Page 168 and 169: HP350 Butterfly Valve Cross Section
- Page 170 and 171: Diviner Position Indicator SAFETY M
- Page 172 and 173: Diviner Position Indicator FUNCTION
- Page 174 and 175: Diviner Position Indicator INSTALLA
- Page 176 and 177: Diviner Position Indicator HOW TO C
- Page 178 and 179: PAINT SYSTEM SUMMARY Page 1 of 5 SY
- Page 180 and 181: Page 3 of 5 UL/FM HENRY PRATT COMPA
- Page 182: Page 5 of 5 UL/FM HENRY PRATT COMPA
- Page 185 and 186: A Tradition of Excellence With the
- Page 187 and 188: MANUAL ACTUATORS Spur G
- Page 189 and 190: MANUAL ACTUATORS
- Page 191 and 192: FEATURES & BENEFITS OF THE TRAVELIN
- Page 193 and 194: ACTUATOR EXTENSIONS
- Page 195 and 196: ACTUATOR EXTENSIONS
24”-48” HP250II <strong>Butterfly</strong> Valve<br />
INSTALLATION<br />
GENERAL<br />
<strong>Valves</strong> are a significant component of any piping system. Failure due to faulty installation, improper operation<br />
or maintenance in such systems could result in damage, down time and costly repairs. In buried underground<br />
installations, problems or malfunctions can result in extensive, costly unearthing operations to correct the<br />
problem. Many problems with valves can be traced to improper installation, operation, or maintenance<br />
procedures.<br />
UNLOADING<br />
Inspect valves on receipt for damage in shipment and conformance with quantity and description in the<br />
shipping notice and order. Carefully unload all valves to the ground without dropping using fork trucks or slings<br />
under skids. Do not lift valves with slings or chain around operating shaft, actuator, or through waterway.<br />
Instead, lift valves with eye bolts or rods through flange holes.<br />
STORAGE<br />
Whenever practical, store valves indoors. If not, protect valves and actuators from weather and accumulation<br />
of water, dirt, rocks and debris. When valves fitted with power actuators and controls are stored, energize<br />
electric actuator or otherwise protect electrical control equipment to prevent corrosion of electrical contacts due<br />
to condensation resulting from temperature variation. Do not expose rubber seats to sunlight or ozone for any<br />
extended period. <strong>Valves</strong> should be stored with the valve disc or closure member slightly open.<br />
INSPECTION PRIOR TO INSTALLATION<br />
Make sure flange faces and joint sealing surfaces, body seats and disc seats are clean. Check bolting<br />
attaching actuator to valve for loosening in transit and handling. If loose, tighten firmly. Open and close valve<br />
to make sure it operates properly and that stops or limit switches are correctly set so that the valve seats fully.<br />
Check that valve rotation direction is correct and close valve before installing.<br />
INSTALLATION<br />
The following items must be performed during installation to ensure proper function.<br />
• Carefully place valves into position avoiding contact or impact with other equipment, vault walls or trench<br />
walls.<br />
Document #: 2448HP250IIOM Revision Date: 1/10/11<br />
5