Download complete user manual (PDF). - Brocade

More documents

Recommendations

Info

2 PIM SM snooping show commands Syntax: show ip multicsat pimsm-snooping group-address | source-address If the address you entered is within the range of source addresses, then the router treats it as the source address. Likewise, if the address falls in the range of group addresses, then the router assumes that you are requesting a report for that group. The following table describes the information displayed by the show ip multicast pimsm-snooping command. Field VLAN ID PIM SM Neighbor list Multicast Group Forwarding Port PIMv2 Group Port Source, Port list Description The port-based VLAN to which the information listed below apply and the number of members in the VLAN. The PIM SM routers that are attached to the Layer 2 Switch ports. The value following “expires” indicates how many seconds the Layer 2 Switch will wait for a hello message from the neighbor before determining that the neighbor is no longer present and removing the neighbor from the list. The IP address of the multicast group. NOTE: The fid and camindex values are used by Brocade Technical Support for troubleshooting. The ports attached to the group receivers. A port is listed here when it receives a join message for the group, an IGMP membership report for the group, or both. The ports on which the Layer 2 Switch has received PIM SM join messages for the group. The IP address of each PIM SM source and the Layer 2 Switch ports connected to the receivers of the source. Displaying PIM SM snooping information for a specific group or source group pair To display PIM SM snooping information for a specific group, enter the following command at any level of the CLI. Brocade#show ip multicast pimsm-snooping 230.1.1.1 Show pimsm snooping group 230.1.1.1 in all vlans vlan 10,has 2 caches. 1 (*230.1.1.1) has 1 pim join ports out of 1 OIF 1(age=120) 1 has 1 src:10.20.20.66(120) To display PIM SM snooping information for a specific (source, group) pair, enter the following command at any level of the CLI. Brocade#show ip multicast pimsm-snooping 230.2.2.2 20.20.20.66 Show pimsm snooping source 10.20.20.66, group 230.2.2.2 in all vlans vlan 10:(*230.2.2.2) has 1 pim join ports out of 2 OIF 1(age=0) 1 has 1 src:10.20.20.66(0) Syntax: show ip multicast pimsm-snooping group-address [source-ip-address] The Brocade device determines which address is the group address and which one is the source address based on the ranges that the address fall into. If the address is within the range of source addresses, then the router treats it as the source address. Likewise, if the address falls in the range of group addresses, then the router assumes it is a group address. 56 FastIron Ethernet Switch IP Multicast Configuration Guide 53-1002638-02
PIM SM snooping show commands 2 The following table describes the information displayed by the show ip multicast pimsm-snooping command. Field Description vlan The VLAN membership ID of the source. port The port on which the source is sending traffic. In this example, the port number is 1. age src The age of the port, in seconds. The source address and age. The age (number of seconds) is indicated in brackets immediately following the source. FastIron Ethernet Switch IP Multicast Configuration Guide 57 53-1002638-02
Page 1 and 2:
53-1002638-02 24 June 2013 ® FastI
Page 3 and 4:
FastIron Ethernet Switch IP Multica
Page 5 and 6:
Contents About This Guide Introduct
Page 7 and 8:
IGMP snooping configuration. . . .
Page 9 and 10:
Displaying PIM Sparse configuration
Page 11 and 12:
About This Guide This chapter conta
Page 13 and 14:
old text italic text code text Iden
Page 15 and 16:
IPv6 Multicast Traffic Reduction Ch
Page 17 and 18:
MLD Snooping Overview 1 Forwarding
Page 19 and 20: MLD Snooping Overview 1 • MLD sno
Page 21 and 22: MLD snooping configuration 1 • Mo
Page 23 and 24: MLD snooping configuration 1 To mod
Page 25 and 26: MLD snooping configuration 1 Syntax
Page 27 and 28: MLD snooping configuration 1 MLDv2
Page 29 and 30: Displaying MLD snooping information
Page 31 and 32: Displaying MLD snooping information
Page 33 and 34: Clearing MLD snooping counters and
Page 35 and 36: PIM6 SM traffic snooping overview 1
Page 37 and 38: PIM6 SM snooping configuration 1 NO
Page 39 and 40: PIM6 SM snooping show commands 1
Page 41 and 42: IPv4 Multicast Traffic Reduction Ch
Page 43 and 44: IGMP snooping overview 2 connection
Page 45 and 46: IGMP snooping overview 2 Configurat
Page 47 and 48: IGMP snooping configuration 2 About
Page 49 and 50: IGMP snooping configuration 2 Confi
Page 51 and 52: IGMP snooping configuration 2 Synta
Page 53 and 54: IGMP snooping configuration 2 Turni
Page 55 and 56: IGMP snooping show commands 2 Broca
Page 57 and 58: IGMP snooping show commands 2 Broca
Page 59 and 60: IGMP snooping show commands 2 Field
Page 61 and 62: IGMP snooping show commands 2 defau
Page 63 and 64: Clear commands for IGMP snooping 2
Page 65 and 66: PIM SM traffic snooping overview 2
Page 67 and 68: PIM SM snooping configuration 2 NOT
Page 69: PIM SM snooping show commands 2 Dis
Page 73 and 74: IP Multicast Protocols Chapter 3 Ta
Page 75 and 76: Support for Multicast Multi-VRF 3 M
Page 77 and 78: Changing global IP multicast parame
Page 79 and 80: Adding an interface to a multicast
Page 81 and 82: Multicast non-stop routing 3 Config
Page 83 and 84: Passive Multicast Route Insertion (
Page 85 and 86: IP Multicast Boundaries 3 Standard
Page 87 and 88: PIM Dense 3 Pruning a multicast tre
Page 89 and 90: PIM Dense 3 Enabling PIM on the dev
Page 91 and 92: PIM Dense 3 Modifying prune timer T
Page 93 and 94: PIM Dense 3 1. If more than one dev
Page 95 and 96: PIM Dense 3 Syntax: show ip pim mca
Page 97 and 98: PIM Dense 3 Field DIT RegPkt AvgRat
Page 99 and 100: PIM Sparse 3 FIGURE 5 Example PIM S
Page 101 and 102: PIM Sparse 3 Configuring global PIM
Page 103 and 104: PIM Sparse 3 The ethernet slot/port
Page 105 and 106: PIM Sparse 3 The optional static RP
Page 107 and 108: Displaying system values 3 NOTE IPv
Page 109 and 110: Displaying PIM Sparse configuration
Page 121 and 122:
Clearing the PIM forwarding cache 3
Page 123 and 124:
Clearing the PIM message counters 3
Page 125 and 126:
Configuring Multicast Source Discov
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Configuring MSDP mesh groups 3 FIGU
Page 141 and 142:
MSDP Anycast RP 3 NOTE The anycast
Page 143 and 144:
MSDP Anycast RP 3 RP2(config-if-e10
Page 145 and 146:
PIM Anycast RP 3 The RP shared addr
Page 147 and 148:
IGMP Proxy 3 • PIM DM must be ena
Page 149 and 150:
IGMP V3 3 Use the show ip igmp prox
Page 151 and 152:
IGMP V3 3 Compatibility with IGMP V
Page 153 and 154:
IGMP V3 3 Syntax: [no] ip igmp trac
Page 155 and 156:
IGMP V3 3 If the tracking and fast
Page 157 and 158:
IGMP V3 3 Displaying the IGMP statu
Page 159 and 160:
IGMP V3 3 Clearing IGMP traffic sta
Page 161 and 162:
IGMP V3 3 Configuring PIM SSM group
Page 163 and 164:
IGMP V3 3 IGMPv2 SSM mapping The PI
Page 165 and 166:
IGMP V3 3 20 2.2.2.4 20 2.2.2.5 20
Page 167 and 168:
IPv6 Multicast Chapter 4 Table 34 d
Page 169 and 170:
IPv6 PIM Sparse 4 To optimize PIM t
Page 171 and 172:
IPv6 PIM Sparse 4 To configure the
Page 173 and 174:
IPv6 PIM Sparse 4 If you explicitly
Page 175 and 176:
IPv6 PIM Sparse 4 Syntax: rp-adv-in
Page 177 and 178:
IPv6 PIM Sparse 4 Brocade(config)#
Page 179 and 180:
IPv6 PIM Sparse 4 Passive Multicast
Page 181 and 182:
IPv6 PIM Sparse 4 The vrf parameter
Page 183 and 184:
IPv6 PIM Sparse 4 TABLE 36 Field Ou
Page 185 and 186:
IPv6 PIM Sparse 4 TABLE 38 Field Ou
Page 187 and 188:
IPv6 PIM Sparse 4 Brocade# show ipv
Page 189 and 190:
IPv6 PIM Sparse 4 L3 (SW) 1: e3/1/1
Page 191 and 192:
IPv6 PIM Sparse 4 Displaying IPv6 P
Page 193 and 194:
IPv6 PIM Sparse 4 TABLE 46 Field Nu
Page 195 and 196:
IPv6 PIM Sparse 4 Clearing the IPv6
Page 197 and 198:
PIM Anycast RP 4 Brocade(config)# i
Page 199 and 200:
Multicast Listener Discovery and so
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
IPv6 Multicast Boundaries 4 IPv6 Mu
Page 211 and 212:
Index C command clear ip multicast
show all

Download complete user manual (PDF). - Brocade

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?