Download complete user manual (PDF). - Brocade

More documents

Recommendations

Info

4 IPv6 PIM Sparse TABLE 43 Field Output from the show ipv6 pim neighbor command Description Port Phyport Neighbor Holdtime sec T Bit PropDelay msec Override msec Age sec UpTime VRF Prio The routing interface through which the device is connected to the neighbor. The physical interface through which the device is connected to the neighbor. The IPv6 interface of the IPv6 PIM neighbor interface. Indicates how many seconds the neighbor wants this device to hold the entry for this neighbor in memory. The neighbor sends the Hold Time in its hello packets. • If the device receives a new hello packet before the Hold Time received in the previous packet expires, the device updates its table entry for the neighbor. • If the device does not receive a new hello packet from the neighbor before the Hold time expires, the device assumes the neighbor is no longer available and removes the entry for the neighbor. Specifies the ability of the sending router to disable joins suppression. Expected propagation delay over the local link. Default delay interval over which to randomize, when scheduling a delayed join message. The number of seconds since the device received the last hello message from the neighbor. The number of seconds the PIM neighbor has been up. This timer starts when the device receives the first hello messages from the neighbor. The DR priority that is used in the DR election process. This can be a configured value or the default value of 1. Displaying the IPv6 PIM multicast cache To display the IPv6 PIM multicast cache, enter the show ipv6 pim mcache command at any CLI level. NOTE <strong>Brocade</strong> NetIron CES and NetIron CER devices display incorrect hardware programmed entries. The information displayed for the forwarding port should be disregarded. <strong>Brocade</strong>#show ipv6 pim mcache IP Multicast Mcache Table Entry Flags : SM - Sparse Mode, SSM - Source Specific Multicast, DM - Dense Mode RPT - RPT Bit, SPT - SPT Bit, LSRC - Local Source, LRCV - Local Receiver HW - HW Forwarding Enabled, FAST - Resource Allocated, TAG - Need For Replication Entry REGPROB - Register In Progress, REGSUPP - Register Suppression Timer MSDPADV - Advertise MSDP, NEEDRTE - Route Required for Src/RP, PRUN - DM Prune Upstream Interface Flags: IM - Immediate, IH - Inherited, WA - Won Assert MJ - Membership Join, MI - Membership Include, ME - Membership Exclude BR - Blocked RPT, BA - Blocked Assert, BF - Blocked Filter, BI - Blocked IIF Total entries in mcache: 4 1 (*, ff05::4422) RP 2006:1001::1, in v503 (tag e2/1/11), Uptime 1d 00:27:26 (SM) upstream neighbor fe80::204:ff:fe05:6 (2006:503::1001) Flags (0x002604a2) SM RPT LRCV TAG slow ports: ethe 3/1/1 AgeSltMsk: 0, L2 FID: 8192, DIT: NotReq, profile: none Forwarding_oif: 1, Immediate_oif: 1, Blocked_oif: 0 174 FastIron Ethernet Switch IP Multicast Configuration Guide 53-1002638-02
IPv6 PIM Sparse 4 L3 (SW) 1: e3/1/1(VL170), 1d 00:27:26/0, Flags: MJ 2 (2006:170::1010, ff34::500) in v170 (tag e3/1/1), Uptime 00:37:51, Rate 0 (SM) Source is directly connected. RP 2006:1001::1 Flags (0x20429ce1) SM SPT REG L2REG LSRC HW FAST TAG fast ports: ethe 2/1/11 AgeSltMsk: 1, L2 FID: 4188, DIT: 1 , AvgRate: 0, profile: none Forwarding_oif: 1, Immediate_oif: 1, Blocked_oif: 0 L3 (HW) 1: TR(e2/1/11,e2/1/11)(VL503), 00:37:26/183, Flags: IM Src-Vlan: 170 Syntax: show ipv6 pim mcache [ multicast cache entries source/group address | multicast cache ipv6-group-address] Syntax: show ipv6 pim [vrf vrf-name] mcache [source-address | group-address | counts | dense | dit-idx dit-idx | g_entries | receiver | sg_entries | sparse | ssm] The vrf option allows you to display the IPv6 PIM multicast cache for the VRF instance identified by the vrf-name variable. The source-address parameter selects the multicast cache source address. The group-address parameter selects the multicast cache group address. The counts keyword indicates the count of entries. The dense keyword displays only the PIM Dense Mode entries. The dit-idx variable allows you to display all entries that match a specified dit. The g_entries keyword displays only the (*, G) entries. The receiver keyword allows you to display all entries that egress a specified interface. The sg_entries keyword displays only the (S, G) entries. The sparse keyword displays only the PIM Sparse Mode entries. The ssm keyword displays only the SSM entries. Table 44 describes the output parameters of the show ipv6 pim vrf mcache command. TABLE 44 Field Output parameters of the show ipv6 pim mcache command Description Total entries in mcache upstream neighbor Flags slow ports ethe AgeSltMsk L2 FID Shows the total number of PIM mcache entries. Shows the upstream neighbor for the Source/RP based on the type of entry. For (*,G) it shows the upstream neighbor towards the RP. For (S,G) entries it shows the upstream neighbor towards the source. Show the flags associated with the forward entry. Shows the forwarding port ID of the mcache entry which is in the software forwarding path. Shows the slot number on which MP expects ingress traffic. Shows the hardware resource allocated for the traffic switched to receivers in the ingress VLAN. FastIron Ethernet Switch IP Multicast Configuration Guide 175 53-1002638-02
Page 1 and 2:
53-1002638-02 24 June 2013 ® FastI
Page 3 and 4:
FastIron Ethernet Switch IP Multica
Page 5 and 6:
Contents About This Guide Introduct
Page 7 and 8:
IGMP snooping configuration. . . .
Page 9 and 10:
Displaying PIM Sparse configuration
Page 11 and 12:
About This Guide This chapter conta
Page 13 and 14:
old text italic text code text Iden
Page 15 and 16:
IPv6 Multicast Traffic Reduction Ch
Page 17 and 18:
MLD Snooping Overview 1 Forwarding
Page 19 and 20:
MLD Snooping Overview 1 • MLD sno
Page 21 and 22:
MLD snooping configuration 1 • Mo
Page 23 and 24:
MLD snooping configuration 1 To mod
Page 25 and 26:
MLD snooping configuration 1 Syntax
Page 27 and 28:
MLD snooping configuration 1 MLDv2
Page 29 and 30:
Displaying MLD snooping information
Page 31 and 32:
Displaying MLD snooping information
Page 33 and 34:
Clearing MLD snooping counters and
Page 35 and 36:
PIM6 SM traffic snooping overview 1
Page 37 and 38:
PIM6 SM snooping configuration 1 NO
Page 39 and 40:
PIM6 SM snooping show commands 1
Page 41 and 42:
IPv4 Multicast Traffic Reduction Ch
Page 43 and 44:
IGMP snooping overview 2 connection
Page 45 and 46:
IGMP snooping overview 2 Configurat
Page 47 and 48:
IGMP snooping configuration 2 About
Page 49 and 50:
IGMP snooping configuration 2 Confi
Page 51 and 52:
IGMP snooping configuration 2 Synta
Page 53 and 54:
IGMP snooping configuration 2 Turni
Page 55 and 56:
IGMP snooping show commands 2 Broca
Page 57 and 58:
IGMP snooping show commands 2 Broca
Page 59 and 60:
IGMP snooping show commands 2 Field
Page 61 and 62:
IGMP snooping show commands 2 defau
Page 63 and 64:
Clear commands for IGMP snooping 2
Page 65 and 66:
PIM SM traffic snooping overview 2
Page 67 and 68:
PIM SM snooping configuration 2 NOT
Page 69 and 70:
PIM SM snooping show commands 2 Dis
Page 71 and 72:
PIM SM snooping show commands 2 The
Page 73 and 74:
IP Multicast Protocols Chapter 3 Ta
Page 75 and 76:
Support for Multicast Multi-VRF 3 M
Page 77 and 78:
Changing global IP multicast parame
Page 79 and 80:
Adding an interface to a multicast
Page 81 and 82:
Multicast non-stop routing 3 Config
Page 83 and 84:
Passive Multicast Route Insertion (
Page 85 and 86:
IP Multicast Boundaries 3 Standard
Page 87 and 88:
PIM Dense 3 Pruning a multicast tre
Page 89 and 90:
PIM Dense 3 Enabling PIM on the dev
Page 91 and 92:
PIM Dense 3 Modifying prune timer T
Page 93 and 94:
PIM Dense 3 1. If more than one dev
Page 95 and 96:
PIM Dense 3 Syntax: show ip pim mca
Page 97 and 98:
PIM Dense 3 Field DIT RegPkt AvgRat
Page 99 and 100:
PIM Sparse 3 FIGURE 5 Example PIM S
Page 101 and 102:
PIM Sparse 3 Configuring global PIM
Page 103 and 104:
PIM Sparse 3 The ethernet slot/port
Page 105 and 106:
PIM Sparse 3 The optional static RP
Page 107 and 108:
Displaying system values 3 NOTE IPv
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Clearing the PIM forwarding cache 3
Page 123 and 124:
Clearing the PIM message counters 3
Page 125 and 126:
Configuring Multicast Source Discov
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138: Configuring Multicast Source Discov
Page 139 and 140: Configuring MSDP mesh groups 3 FIGU
Page 141 and 142: MSDP Anycast RP 3 NOTE The anycast
Page 143 and 144: MSDP Anycast RP 3 RP2(config-if-e10
Page 145 and 146: PIM Anycast RP 3 The RP shared addr
Page 147 and 148: IGMP Proxy 3 • PIM DM must be ena
Page 149 and 150: IGMP V3 3 Use the show ip igmp prox
Page 151 and 152: IGMP V3 3 Compatibility with IGMP V
Page 153 and 154: IGMP V3 3 Syntax: [no] ip igmp trac
Page 155 and 156: IGMP V3 3 If the tracking and fast
Page 157 and 158: IGMP V3 3 Displaying the IGMP statu
Page 159 and 160: IGMP V3 3 Clearing IGMP traffic sta
Page 161 and 162: IGMP V3 3 Configuring PIM SSM group
Page 163 and 164: IGMP V3 3 IGMPv2 SSM mapping The PI
Page 165 and 166: IGMP V3 3 20 2.2.2.4 20 2.2.2.5 20
Page 167 and 168: IPv6 Multicast Chapter 4 Table 34 d
Page 169 and 170: IPv6 PIM Sparse 4 To optimize PIM t
Page 171 and 172: IPv6 PIM Sparse 4 To configure the
Page 173 and 174: IPv6 PIM Sparse 4 If you explicitly
Page 175 and 176: IPv6 PIM Sparse 4 Syntax: rp-adv-in
Page 177 and 178: IPv6 PIM Sparse 4 Brocade(config)#
Page 179 and 180: IPv6 PIM Sparse 4 Passive Multicast
Page 181 and 182: IPv6 PIM Sparse 4 The vrf parameter
Page 183 and 184: IPv6 PIM Sparse 4 TABLE 36 Field Ou
Page 185 and 186: IPv6 PIM Sparse 4 TABLE 38 Field Ou
Page 187: IPv6 PIM Sparse 4 Brocade# show ipv
Page 191 and 192: IPv6 PIM Sparse 4 Displaying IPv6 P
Page 193 and 194: IPv6 PIM Sparse 4 TABLE 46 Field Nu
Page 195 and 196: IPv6 PIM Sparse 4 Clearing the IPv6
Page 197 and 198: PIM Anycast RP 4 Brocade(config)# i
Page 199 and 200: Multicast Listener Discovery and so
Page 209 and 210: IPv6 Multicast Boundaries 4 IPv6 Mu
Page 211 and 212: Index C command clear ip multicast
show all

Download complete user manual (PDF). - Brocade

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?