technical manu al table of contents - Jamestown Distributors

More documents

Recommendations

Info

One-component interior satin varnish system on wood above the waterline Surface Preparation: Fill the bare wood to a smooth surface with Epifanes Clear Gloss Varnish, Epifanes Wood Finish Gloss or Epifanes Polyurethane Clear Gloss. Approx. 3 - 4 coats. These sealer coats provide maximum durability and U.V. protection (see leaflet on Clear Gloss Varnish, Wood Finish Gloss or Polyurethane Clear Gloss for application instructions). A build up of gloss also produces a finish with more depth and clarity. After build up, degrease with Epifanes Spray Thinner For Paint & Varnish or denatured alcohol and sand coat with 320 or 400 grit wet or dry abrasive paper. Brush application with a good quality, clean, natural bristle brush will give good results. Try an Epifanes brush for the ultimate varnishing experience. Foam brushes are convenient on smaller projects however, are not suitable for larger jobs. "Roll and tip" is a great method for large flat areas. 3" foam roller followed by a bristle brush is the best combination. Coats Product Thinner Thinning Ratio % Drying Time in hours Abrasive paper grit Abrasive paper type Approx. coverage / Remarks First Rubbed Effect Interior Varnish Brush Thinner For P & V 0 - 5 12 at 65F. 320 - 400 Wet or Dry 140 sq. feet Always stir Second Rubbed Effect Interior Varnish Brush Thinner For P & V 0 - 5 12 at 65F. 320 - 400 Wet or Dry 140 sq. feet Always stir Maintenance: If existing coats of varnish are intact, one or more coats of Epifanes Rubbed Effect Interior Varnish may be applied on a well cleaned, degreased and lightly sanded surface. An existing varnish system in poor condition must be removed. Weathered spots may be treated with a cleaning or bleaching product. If either are used, wash down the surface thoroughly with fresh water in order to remove any residue. Allow the surface to dry. Smaller spots needing repair may be filled with several coats of varnish. When an equal level has been achieved, sand to a smooth surface and apply one or more coats of Rubbed Effect Varnish on the entire surface.
EPIFANES POLYURETHANE CLEAR GLOSS The ultimate in hardness! Type Color Gloss Recommended use Film characteristics Container Size Density Solids Content Recommended film thickness Application Two-component clear finish based on unsaturated polyesters. Water clear Ultra high gloss For long lasting protection of all marine or household woods. Interior and exterior wood above the waterline. Due to the hard nature of this finish, Epifanes Polyurethane Clear Gloss is ideally suited for plywoods and coating epoxy resins. Perfect for saloon tables and cabin soles. Superior flow, gloss and durability. High U.V. protection and resistance to abrasion, weathering, chemicals and loss of gloss. The outstanding flow characteristics make this two-component varnish highly suitable for both brush and spray application. 750 gr. (500 gr. base + 250 gr. reactor = 750 gr. mixed) 2:1 mix by weight. 1.08 kg./liter mixed 45 +/- 2 vol. % Per coat wet - 80 micron Per coat dry - 35 micron Brush, roller (phenolic core), conventional air spray, H.V.L.P. Drying times at 65F / 65% RH Tack free - 1 hour Dry - 24 hours Tape free - 18 hours Recoatable - approx. 24 hours Spray Application Additives Application conditions Conventional air: Thin as needed up to 10% with Epifanes Polyurethane Thinner For Spray. Spray viscosity 20 - 22 seconds Din Cup 4, 16 - 18 seconds Ford Cup 4. Nozzle 1.6 mm. - 1.8 mm. Pressure 2-3 Bar. Apply light tack coat to fully wet the surface. Allow 15-20 minutes to dry, then coat the entire surface. Airless spray not recommended. Epifanes Polyurethane Retarder Temperature should be between 60F. and 80F. during application. Air humidity below 70%. Avoid varnishing in too much wind or sun. A rapid loss of solvents will occur under these conditions and will decrease the flowing ability. Add thinner up to the specified percentage to compensate for the faster release of solvents. Any existing finish must be intact, degreased and sanded. DISCLAIMER OF WARRANTIES: Seller makes no express warranties. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. In the event a warranty is created by law, buyer’s EXCLUSIVE REMEDY shall be the replacement of any defective product. No other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available to buyer. Some States do not allow the exclusion of implied warranties or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. Epifanes North America Inc. 70 Water Street Thomaston, Maine 04861 U.S.A. tel. 800-269-0961 fax. 207-354-0387 http://www.epifanes.com
Page 1 and 2: TABLE OF CONTENTS TECHNICAL MANUAL
Page 3 and 4: EPIFANES CLEAR GLOSS VARNISH Faster
Page 5 and 6: EPIFANES RAPIDCLEAR Quick and Easy
Page 7 and 8: EPIFANES RAPIDCOAT Quick and Easy W
Page 9 and 10: EPIFANES WOOD FINISH GLOSS The ulti
Page 11 and 12: EPIFANES WOOD FINISH MATTE Exterior
Page 13: EPIFANES RUBBED EFFECT INTERIOR VAR
Page 17 and 18: EPIFANES POLYURETHANE CLEAR SATIN H
Page 19 and 20: EPIFANES PP VARNISH EXTRA High buil
Page 21 and 22: EPIFANES TEAK OIL Type Color Gloss
Page 23 and 24: EPIFANES YACHT ENAMEL Flexibility a
Page 25 and 26: EPIFANES MONOURETHANE Hardest finis
Page 27 and 28: EPIFANES POLYURETHANE TOPCOAT Harde
Page 29 and 30: EPIFANES NAUTIFORTE Highest gloss,
Page 31 and 32: EPIFANES EGGSHELL ENAMEL Type Color
Page 33 and 34: CHAPTER THREE PRIMERS 6 Pages
Page 35 and 36: EPIFANES FIBERGLASS PRIMER Maximize
Page 37 and 38: WERDOL METALPRIMER Type Color Gloss
Page 39 and 40: EPIFANES EPOXY PRIMER Type Color Gl
Page 41 and 42: ACCESSORIES Brushes, Brushkeeper, R
Page 43 and 44: Degreasing: Before sanding, be sure
Page 45 and 46: Maintenance: An important considera
Page 47 and 48: Question: What is the best way to r
Page 49 and 50: Question: Why do varnish manufactur
Page 51 and 52: Question: To what extent if any, do
Page 53 and 54: In answer to your question, if you
Page 55 and 56: any better (or worse) than a specif
Page 57 and 58: Answer: You may be referring to one
Page 59 and 60: generally quick to dry, and easier
Page 61 and 62: difficult to remove at a later date
Page 63: CHAPTER EIGHT CANADA PRICELIST 3 Pa

technical manu al table of contents - Jamestown Distributors

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?