Applications Guide Tracer Graphical Programming - Trane
Applications Guide Tracer Graphical Programming - Trane Applications Guide Tracer Graphical Programming - Trane
® Special notifications and formats The following notifications and formats may appear at appropriate locations throughout this manual. Read warnings and cautions carefully. !WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. !CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. CAUTION Indicates a situation that may result in equipment or property-damage-only accidents. IMPORTANT Alerts installer, servicer, or operator to potential actions that could cause the product or system to operate improperly but will not likely result in potential for damage. Note: A note may be used to make the reader aware of useful information, to clarify a point, or to describe options or alternatives. ◆ This symbol precedes a procedure that consists of only a single step. ➤ Explanatory information Text in this format provides explanations that you can read for further information on a particular subject or concept. The information is not necessary to complete the task. CNT-APG001-EN
® Contents Chapter 1 Using the Tracer Graphical Programming editor. . 1 About this book. . . . . . . . . . . . .................................. 1 Roverservicetooloverview.................................... 2 About the Tracer MP580/581 controller . . . . . ..................... 2 OpeningtheTGPeditor....................................... 2 TGPeditor.................................................. 4 Designspace............................................. 4 Outputdisplay ........................................... 4 Blocks .................................................. 5 Menubar................................................ 5 Toolbars................................................. 6 Standardtoolbar...................................... 6 Alignmenttoolbar..................................... 6 Blocktoolbars......................................... 7 Programtoolbar....................................... 8 Showingorhidingtoolbars ............................. 8 Shortcutmenus .......................................... 9 Keyboardshortcuts ....................................... 9 UsingonlineHelp........................................ 10 Chapter2 Writingtheexhaustfanprogram............. 11 Whatyouwilllearn...........................................11 Skills . ..................................................11 Conceptsanddefinitions...................................11 Blocks ................................................. 12 Reviewingthesequenceofoperation........................... 12 Openinganewprogram ..................................... 15 Editingprogramproperties................................... 15 Addingablock ............................................. 17 Editingblockproperties...................................... 18 UsingaConstantblock....................................... 19 Addingacomment.......................................... 21 CNT-APG001-EN v
- Page 1: Applications Guide Tracer Graphical
- Page 4 and 5: CNT-APG001-EN ®
- Page 8 and 9: ® Contents Arrangingblocks........
- Page 10 and 11: ® Contents Chapter 5 Cooling tower
- Page 12 and 13: ® Contents Chapter7 Constant-volum
- Page 14 and 15: ® Contents Summary-question answer
- Page 16 and 17: ® Figures Chapter3 Modifyingtheexh
- Page 18 and 19: ® Figures Figure 96: Input blocks
- Page 20 and 21: ® Figures Chapter 8 Constant-volum
- Page 22 and 23: ® Figures xx CNT-APG001-EN
- Page 24 and 25: ® Tables Chapter7 Constant-volumeA
- Page 26 and 27: ® Chapter 1 Using the Tracer Graph
- Page 28 and 29: ® Chapter 1 Using the Tracer Graph
- Page 30 and 31: ® Chapter 1 Using the Tracer Graph
- Page 32 and 33: ® Chapter 1 Using the Tracer Graph
- Page 34 and 35: ® Chapter 1 Using the Tracer Graph
- Page 36 and 37: ® Chapter 2 Writing the exhaust fa
- Page 38 and 39: ® Chapter 2 Writing the exhaust fa
- Page 40 and 41: ® Chapter 2 Writing the exhaust fa
- Page 42 and 43: ® Chapter 2 Writing the exhaust fa
- Page 44 and 45: ® Chapter 2 Writing the exhaust fa
- Page 46 and 47: ® Chapter 2 Writing the exhaust fa
- Page 48 and 49: ® Chapter 2 Writing the exhaust fa
- Page 50 and 51: ® Chapter 2 Writing the exhaust fa
- Page 52 and 53: ® Chapter 2 Writing the exhaust fa
- Page 54 and 55: ® Chapter 3 Modifying the exhaust
®<br />
Contents<br />
Chapter 1 Using the <strong>Tracer</strong> <strong>Graphical</strong> <strong>Programming</strong> editor. . 1<br />
About this book. . . . . . . . . . . . .................................. 1<br />
Roverservicetooloverview.................................... 2<br />
About the <strong>Tracer</strong> MP580/581 controller . . . . . ..................... 2<br />
OpeningtheTGPeditor....................................... 2<br />
TGPeditor.................................................. 4<br />
Designspace............................................. 4<br />
Outputdisplay ........................................... 4<br />
Blocks .................................................. 5<br />
Menubar................................................ 5<br />
Toolbars................................................. 6<br />
Standardtoolbar...................................... 6<br />
Alignmenttoolbar..................................... 6<br />
Blocktoolbars......................................... 7<br />
Programtoolbar....................................... 8<br />
Showingorhidingtoolbars ............................. 8<br />
Shortcutmenus .......................................... 9<br />
Keyboardshortcuts ....................................... 9<br />
UsingonlineHelp........................................ 10<br />
Chapter2 Writingtheexhaustfanprogram............. 11<br />
Whatyouwilllearn...........................................11<br />
Skills . ..................................................11<br />
Conceptsanddefinitions...................................11<br />
Blocks ................................................. 12<br />
Reviewingthesequenceofoperation........................... 12<br />
Openinganewprogram ..................................... 15<br />
Editingprogramproperties................................... 15<br />
Addingablock ............................................. 17<br />
Editingblockproperties...................................... 18<br />
UsingaConstantblock....................................... 19<br />
Addingacomment.......................................... 21<br />
CNT-APG001-EN<br />
v