DRIVER'S MANUAL SB220GS - Training Registration System

More documents

Recommendations

Info

Coolant is a harmful liquid. In order to avoid poisoning, avoid skin contact. In order to avoid damage when pouring cold liquid into a hot engine, let the engine run and pour slowly. 1. Set the heater’s temperature turning knob to “warm”. 2. Remove the filler cap (4) from the expansion tank. 3. Let the engine run for a few minutes. 4. Switch off the engine and check the coolant level. 5. The coolant level should be between the MAX and MIN marks. Top-up with coolant if necessary. Filling procedure cooling system 1. Close all heater valves and open the filler cap on the expansion tank. 2. Fill the expansion tank to the maximum level (engine not running). 3. Close the filler cap on expansion tank. 4. Start the engine and allow it to idle for several minutes. 5. Open the filler cap on the expansion tank and top up the expansion tank to the maximum level. 6. Gradually open the heater’s supply valve and simultaneously top-up the expansion tank to the maximum level. 7. Open the heater breathers for a few seconds and top up the expansion tank to the maximum level. Repeat this step until no more air is released from the breather. 8. Open the return valve of the heater and wait until no air is coming up through the expansion tank. 9. Operate the engine at 1500 rpm until no air comes up through the expansion tank. Top up the expansion tank to the max.level. 10. Make a test drive to check for leakage. TYRES AND RIMS - Check the tyres for wear, any foreign matter embedded in the tread and other damage. - Remove any foreign matter from the tread and from between twin tyres. - Check the wheel attachment. - Check the tyre pressure (do not forget the spare). Checking and adjusting the pressure must be done when the tyres are cold. - Do not fit tyres of different sizes otherwise the ABS system will not work correctly. The difference in the depth of tread must also not be greater than 7,5% (also see Replacing Tyres). 52 MAINTENANCE
LIGHTING AND INSTRUMENTS - Check the vehicle lighting, brake lights and instruments for correct operation. - Also check the horn, windscreen wipers and washers for correct operation. DRIVER’S SEAT AND MIRRORS - Adjust the seat and mirrors to the correct position. MAINTENANCE 53
Page 1 and 2: DRIVER’S MANUAL SB220GS Date 9702
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION ....
Page 5 and 6: INTRODUCTION This instruction manua
Page 7 and 8: COLD-WEATHER CONDITIONS Mount winte
Page 9 and 10: Always disconnect the battery earth
Page 11 and 12: -R05926- 01490B 01491B IDENTIFICATI
Page 13 and 14: IDENTIFICATION PLATE 1. Gross combi
Page 15 and 16: IDENTIFICATION 15
Page 17 and 18: The dashboard may differ in each ve
Page 19 and 20: 33. Raise/lower vehicle switch* 34.
Page 21 and 22: 11. YELLOW CENTRAL WARNING LAMP* Th
Page 23 and 24: 26. VOLT METER/RETARDER TEMPERATURE
Page 25 and 26: The tachograph disc has a maximum r
Page 27 and 28: mph v min 25 km /h v max125 km/h 12
Page 29 and 30: The minimum value obtainable: 25% o
Page 31 and 32: 38. DIFFERENTIAL LOCK SWITCH* The r
Page 33 and 34: OIL PRESSURE WARNING LAMP (B5) The
Page 35 and 36: LEFT MULTI-FUNCTION SWITCH Dipped b
Page 37 and 38: DRIVING CONTACT SWITCH/STARTER SWIT
Page 39 and 40: START PROCEDURE When starting the e
Page 41 and 42: 3 - position for hilly routes: 1st,
Page 43 and 44: If the door-controlled brake is in
Page 45 and 46: - With the vehicle stationary or mo
Page 47 and 48: E-GAS (ELECTRONIC THROTTLE CONTROL)
Page 49 and 50: The vehicle can only be returned to
Page 51: 2 Max. 3 DAF 4 Max. Min. -18 c Min.
Page 55 and 56: FRONT/ REAR 1 A 1187168 00736B 0148
Page 57 and 58: Damp air in the air-operated brake
Page 59 and 60: PREVENTIVE MAINTENANCE AFTER THE WI
Page 61 and 62: V-BELTS Renewing V-Belts - Always f
Page 63 and 64: 01499B BLEEDING THE FUEL SYSTEM Die
Page 65 and 66: After changing a tyre, the differen
Page 67 and 68: FUSES - The central panel of the el
Page 69 and 70: FUSES AND RELAYS E000 Fuse 7.5A, LH
Page 71 and 72: RELAYS G008 Relay windscreen wipers
Page 73 and 74: RELAYS G059 Relay retarder operatio
Page 75 and 76: Fuel system Injection order 1-5-3-6
Page 77 and 78: Wheels Wheel bolts tightening torqu
Page 79 and 80: Specification gearbox and intermedi
Page 81 and 82: Specification of coolants Coolant i
Page 83 and 84: LUBRICATION CHART 83
Page 85 and 86: ECAS warning lamp .................
Page 87 and 88: Tyres and rims ....................

DRIVER'S MANUAL SB220GS - Training Registration System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?