english - Michael W. Buder

More documents

Recommendations

Info

SECTION 1 DESCRIPTION F2. Blank Plates 1. Blank Plates- The Blank Plates are available to install on the plenum where an air finger is not required. Half Blank Plate Outer Plate Blank Plate Inner Plate Finger Manifold Assembly Baffle Figure 1-9. Blank Plates (two sizes) and an Air Finger. 8
SECTION 2 INSTALLATION SECTION 2 INSTALLATION NOTE: The oven, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code (NEC), or ANSI/NFPA70. NOTE There must be adequate clearance between the oven and any adjacent combustible construction. Clearance must also be provided for servicing and for operation. CAUTION It is required that the oven be placed under a ventilation hood for adequate air supply and ventilation. CAUTION Do not obstruct the flow of combustion and ventilation air to and from your oven. Do not obstruct the ventilation holes in the Control Panel. CAUTION On ovens with the Machinery Drive Compartment located at the right end, a minimum clearance of 0″ to a left side wall, 18″ to a right side wall and 6″ from a back wall to air openings at the rear of the oven must be maintained. On ovens with the machinery/drive compartment located at the left end, a minimum clearance of 0″ to a right side wall, 18″ to a left side wall and 6″ from a back wall to air openings at the rear of the oven must be maintained. For servicing and cleaning, a minimum of 18″ clearance from all walls is recommended. I. UNLOADING Your Blodgett BE2136-Series Oven is shipped partially assembled. It will arrive in a carton on a crate. Carton size for a BE2136-Series Oven is: 58″ (2134mm) Long × 47.25″ (1473mm) Wide × 36″ (1118mm) High × The crate and carton must be examined before signing the Bill of Lading. Report any visible damage to the transport company, and check for the proper number of crates. If apparent damage is found, make arrangements to file a claim against the carrier. Surface Interstate Commerce Regulations (U.S.A.) require that the claim must be initiated by the consignee within 10 days from the date that the shipment is received. A Pre-installation Procedures Manual (MM P/N 88910-0009) is attached to the exterior wall of the carton. This manual contains detailed instructions on unpacking and moving the oven(s) to the operating site. When the transport company notifies you of an impending delivery, arrange to have a forklift at your facility to unload the carton(s). Instructions for stacking the ovens is continued in a separate manual used by Blodgett Authorized Installers. If you have a door wider than the carton, simply move the carton into your facility and arrange an appointment with your Blodgett Authorized Installer. If your door is narrower than the carton, then the oven will have to be unpacked. Follow the directions shown in the Pre-Installation Procedures Manual. 9
Page 2 and 3: IMPORTANT WARNING: IMPROPER INSTALL
Page 5 and 6: TABLE OF CONTENTS Page TABLE OF CON
Page 7 and 8: SECTION 1 DESCRIPTION SECTION 1 DES
Page 9 and 10: II. PRINCIPLE OF AIR FLOW The fan-s
Page 11 and 12: III. COMPONENT FUNCTION (Figure 1-6
Page 13: SECTION 1 DESCRIPTION Figure 1-8. C
Page 17 and 18: SECTION 2 INSTALLATION Figure 2-1 -
Page 19 and 20: SECTION 2 INSTALLATION Figure 2-6.
Page 21 and 22: UTILITY ROUGH-IN DIMENSIONS AND POS
Page 23 and 24: III. ELECTRICAL CONNECTION INFORMAT
Page 25 and 26: SECTION 3 OPERATION SECTION 3 OPERA
Page 27 and 28: SECTION 3 OPERATION E. Conveyor The
Page 29 and 30: SECTION 3 OPERATION D C B A LOCATIO
Page 31 and 32: SECTION 3 OPERATION "SP LOCK" Light
Page 33 and 34: SECTION 4 MAINTENANCE SECTION 4 MAI
Page 35 and 36: II. MAINTENANCE - MONTHLY NOTE: The
Page 37 and 38: B. Air Fingers Disassembly For Clea
Page 39 and 40: 4. Replace the air fingers by pushi
Page 41 and 42: E. Reinstall End Plugs 1. Reinstall
Page 43 and 44: H. Conveyor Belt Link Removal 1. Us
Page 45 and 46: 4. Reassemble conveyor drive chain
Page 47 and 48: D. Split-belt Conveyor Shaft Cleani
Page 49 and 50: 12. Slide shaft assembly to right s
Page 51 and 52: SECTION 5 TROUBLESHOOTING SECTION 5
Page 53 and 54: SECTION 6 - PARTS LIST SECTION 6 PA
Page 55 and 56: SECTION 6 PARTS LIST OVEN PANELS, W
Page 57 and 58: SECTION 6 PARTS LIST CONTROL PANEL
Page 59 and 60: SECTION 6 PARTS LIST BLOWER AND SHR
Page 61 and 62: SECTION 6 PARTS LIST CONVEYOR P/N -
Page 63 and 64: SECTION 6 PARTS LIST SPLIT BELT CON
Page 65 and 66:
SECTION 6 PARTS LIST MACHINERY COMP
Page 67 and 68:
SECTION 7 ELECTRICAL SCHEMATICS SEC
Page 69 and 70:
SECTION 7 ELECTRICAL SCHEMATICS Wir
Page 71 and 72:
NOTES SECTION 7 ELECTRICAL SCHEMATI
Page 74:
WARNING Improper installation, adju
show all

english - Michael W. Buder

Create successful ePaper yourself

Delete template?

Save as template?