(PDF) h50-0040 - Cloverdale Paint
(PDF) h50-0040 - Cloverdale Paint
(PDF) h50-0040 - Cloverdale Paint
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
General Properties<br />
Recommended Uses<br />
ClovaTherm<br />
Hi-Heat Resistant Enamel<br />
83225<br />
DATA SHEET<br />
A state-of-the-art silicone coating that can be subjected to temperatures up to 420 o C (790 o F) without the need for a heat<br />
cure to develop maximum performance properties. This single component fast drying enamel dries to a rich, low sheen<br />
finish with excellent heat resistance properties. ClovaTherm Hi Heat Resistant Enamel can be used as a self-priming,<br />
direct-to-metal enamel or used in combination with 83220 ClovaTherm Zinc for superior corrosion performance.<br />
This product is for use on steel surfaces where excellent heat resisting performance is required. ClovaTherm is an<br />
excellent alternative to conventional high heat coatings that require a heat cure and are subject to mechanical damage<br />
and weathering. See your <strong>Cloverdale</strong> <strong>Paint</strong> Technical Representative for recommendations for your project.<br />
Product Information<br />
GENERIC TYPE<br />
MIXED RATIO<br />
Silicone Resin<br />
N/A<br />
PIGMENT TYPE<br />
INDUCTION TIME<br />
Heat Resistant<br />
N/A<br />
COLOR<br />
POT LIFE<br />
83225 Aluminum, 83224 Black N/A<br />
BASES<br />
VISCOSITY MIXED<br />
N/A<br />
65 - 70 K.U.<br />
TEMPERATURE RESISTANCE (DRY)<br />
FINISH<br />
400 o C (752 o F) Continuous<br />
Low Sheen<br />
420 o C (788 o F) Intermittent<br />
AVERAGE VOLUME SOLIDS<br />
V.O.C. MIXED<br />
52% 433 g/L (3.61 lbs/gal)<br />
AVERAGE WEIGHT SOLIDS<br />
61%<br />
RECOMMENDED FILM THICKNESS<br />
MAXIMUM THINNING TO OBTAIN V.O.C. OF<br />
420 g/L (3.5 LBS/GAL)<br />
N/A<br />
Wet: 1.9 - 2.9 mils<br />
Dry: 1.0 - 1.5 mils<br />
See your <strong>Cloverdale</strong> Representative for project<br />
recommendations.<br />
THINNER<br />
78011 Xylene<br />
THEORETICAL COVERAGE<br />
ACCELERATOR<br />
834.1 ft 2 /gal @1 mil (25 microns) DFT N/A<br />
20.8 m 2 /L @ 1 mil (25 microns) DFT<br />
Actual coverage may vary depending on substrate and<br />
application methods.<br />
Methods of Application<br />
AIRLESS SPRAY<br />
Speeflo Atlas 30:1 with tip sizes .015" - .021" or equivalent<br />
H.V.L.P.<br />
CONVENTIONAL<br />
BRUSH / ROLLER<br />
Binks Model Mach 1 94 x 97AP (pressure) or equivalent<br />
Binks Model 95GUN 63CSS X 63PB (pressure) or equivalent<br />
Brushing and rolling is limited to small areas or touch-up<br />
Drying Time - Temperature, Relative Humidity, and Film Thickness will affect dry and re-coat times.<br />
Substrate<br />
Temperature<br />
Touch Dry<br />
20 o C (68 o F) 15 minutes<br />
Hard Dry<br />
Overcoat Interval<br />
Minimum Maximum Normal<br />
1 hour N/A N/A N/A<br />
83225 Page 1 of 2 <strong>h50</strong>-<strong>0040</strong>
Recommended Primer<br />
8322 Series<br />
STEEL<br />
CONCRETE<br />
GALVANIZED<br />
ALUMINUM<br />
Self Priming or topcoat with 83225 ClovaTherm Zinc for superior corrosion protection<br />
Not recommended<br />
Not recommended<br />
Not recommended<br />
Surface Preparation<br />
Surfaces to be coated must be clean, dry and free from grease, oil or other contaminants. All mill scale or<br />
weld spatter must be removed for maximum performance. The minimum surface preparation required is<br />
SSPC-SP3 Power Tool Cleaning but an SSPC-SP6 Commercial Sandblast is recommended for improved<br />
product performance. Surface profile should not exceed 1.25 mils as this is a thin film coating.<br />
Typical Resistance (Non-immersion)<br />
WEATHER GOOD<br />
SALT WATER<br />
GOOD<br />
ACIDS<br />
FAIR<br />
MOISTURE<br />
GOOD<br />
FRESH WATER<br />
GOOD<br />
ALKALIS<br />
FAIR<br />
SOLVENTS<br />
Limitations<br />
Do not apply where surface temperatures will exceed recommended temperature resistance levels. Not for immersion<br />
service. When 83220ClovaTherm Zinc is used as a base coat and top coated with 83225 Aluminum or 83224 Black<br />
ClovaTherm, total dry film thickness of the two coat system shall not exceed 2 mils dry.<br />
Mixing Instructions<br />
GOOD<br />
ABRASION<br />
GOOD<br />
Mix well before use and during use. Seal containers tightly when not in use.<br />
OIL<br />
GOOD<br />
Safety Precautions<br />
This product is for industrial use only. Refer to Material Safety Data Sheet for proper health and safety information.<br />
Storage and Handling<br />
FLASH POINT<br />
PRODUCT WEIGHT<br />
STORAGE<br />
PACKAGE SIZE<br />
24 o C (75 o F) TCC<br />
9.67 lbs/gal (container extra)<br />
Cool, dry, well ventilated area. See your <strong>Cloverdale</strong> <strong>Paint</strong> Representative.<br />
1 gallon, 5 gallon<br />
Some package sizes or colors may be by special order only. Please check with your <strong>Cloverdale</strong> Representative when ordering.<br />
Warranty Disclaimer<br />
<strong>Cloverdale</strong> <strong>Paint</strong> manufactures quality products. In the event that this product is defective or in any way unsuitable for the application for which it is sold, <strong>Cloverdale</strong> <strong>Paint</strong> Inc.<br />
will replace the product free of charge. The warranty provided by this data sheet is the only waranty or guarantee of quality made in respect of this product by <strong>Cloverdale</strong> <strong>Paint</strong><br />
Inc. By purchasing this product the customer accepts this warranty in lieu of all others, and waives all claims to any other remedy arising from any warranty or guarantee of<br />
quality, whether such warranty or guarantee of quality was made expressly to the customer or implied by any applicable law.<br />
Check for recent amendments to this data sheet at www.cloverdalepaint.com/html/catalog_recent_ir.asp<br />
<strong>Cloverdale</strong> <strong>Paint</strong> Inc.<br />
6950 King George Highway, Surrey, British Columbia, Canada V3W 4Z1<br />
Web Site: www.cloverdalepaint.com Email: helpdesk@cloverdalepaint.com<br />
Phone: 604 596 6261 Fax: 604 597 2677<br />
<strong>h50</strong>-<strong>0040</strong>v1<br />
12-Dec-05<br />
83225 Page 2 of 2 <strong>h50</strong>-<strong>0040</strong>
Change language