16803 Timberlox Oil Base Solid Hide Stain - Cloverdale Paint
16803 Timberlox Oil Base Solid Hide Stain - Cloverdale Paint
16803 Timberlox Oil Base Solid Hide Stain - Cloverdale Paint
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
TECHNICAL SPECIFICATIONS DATA SHEET<br />
<strong>16803</strong><br />
<strong>Timberlox</strong> <strong>Oil</strong> <strong>Base</strong> <strong>Solid</strong> <strong>Hide</strong> <strong>Stain</strong><br />
Product Description<br />
<strong>Timberlox</strong> <strong>Oil</strong> <strong>Base</strong> <strong>Solid</strong> <strong>Hide</strong> <strong>Stain</strong> is a premium quality, self-priming, highly pigmented oil stain that<br />
provides a solid color appearance without obliteration of the natural texture of the wood. The penetrating<br />
formula conditions wood fibres, while providing long lasting water repellant protection. Available in standard<br />
premixed colors and tint bases which can be tinted to a wide range of popular colors. This product is<br />
approved by the Master <strong>Paint</strong>er's Institute under category #14.<br />
Intended Uses<br />
Use on new or previously stained wood surfaces such as siding, shakes, shingles, fences etc. Not<br />
recommended for horizontal surfaces such as decks.<br />
Product Data<br />
Color:<br />
White and custom colors plus premixed colors 16829 Oxford<br />
Brown, 16827 Chocolate, 16877 Russett, 16839 Cedar, 16865<br />
Forest Green, 16859 Navajo Red, 16863 Cape Cod Grey<br />
Drying Time: (@20 o C 50% Relative Humidity)<br />
Tack Free:<br />
1 Hour<br />
Finish:<br />
Flat<br />
<strong>Base</strong>s:<br />
<strong>16803</strong> White, 16801 Deep, 16804 Clear<br />
Vehicle Type:<br />
Alkyd<br />
Re-Coat:<br />
Thinner:<br />
78001 Mineral Spirits<br />
16 Hours<br />
Flash Point (Tag Closed Cup):<br />
42 o C (107 o F)<br />
Viscosity:<br />
58 - 63 KU #4 Ford Cup<br />
<strong>Solid</strong>s by Volume:<br />
53% V.O.C. (Before Thinning):<br />
435 g/L or 3.61 lbs/gal<br />
<strong>Solid</strong>s by Weight:<br />
74%<br />
Recommended Film Thickness<br />
(Per Coat):<br />
Dry: 3.9 - 5.8 mils (99 - 147 microns)<br />
Wet: 2.0 - 3.0 mils (51 - 76 microns)<br />
Theoretical Coverage (Per Coat):<br />
540 - 800 ft 2 /gal (13.25 - 19.63 m 2 /L)<br />
<strong>16803</strong> Page 1 of 2<br />
40-0050
Surface Preparation<br />
All surfaces must be clean, dry, free of powdery materials, and loose or scaling paint. If mildew is present,<br />
surface should be washed with a chlorine bleach solution (20% bleach, 1 % liquid detergent in water) see<br />
"Special Note". To avoid lap marks, keep a "wet edge" by stopping only at natural breaks such as windows,<br />
doors or the natural course of the siding.<br />
Recommended Primer<br />
Drywall<br />
Wood<br />
- N/A<br />
- Self-Priming or 15130 Exterior<br />
Alkyd <strong>Stain</strong> Blocking Primer<br />
Method<br />
Thinning<br />
- Brush (preferred, this works the<br />
stain into the surface), roller, H.V.L.P.<br />
or airless spray<br />
- Not normally required. Up to 10%<br />
with 78001 Clova Thinner No.1<br />
(Mineral Spirits) for spraying<br />
Masonry<br />
- Self-Priming<br />
Cleanup<br />
- Use 78001 Mineral Spirits<br />
Steel<br />
- N/A<br />
For detailed information please refer to MSDS<br />
Check for recent amendments to this data sheet at www.cloverdalepaint.com<br />
Safety Precautions<br />
Warning<br />
CONTAINS PETROLEUM DISTILLATE. HARMFUL IF SWALLOWED. CAUSES EYE AND SKIN<br />
IRRITATION. VAPOUR HARMFUL. COMBUSTIBLE. KEEP OUT OF REACH OF CHILDREN. Keep away<br />
from heat, sparks, and open flame. Do not take internally. Avoid contact with eyes and skin, and breathing<br />
of vapour or spray mist. Wear an air supplied mask when applying in enclosed areas. Wash thoroughly after<br />
handling. Close container after EACH use. USE WITH ADEQUATE VENTILATION.<br />
First Aid<br />
In case of eye contact, flush immediately with plenty of water for at least 15 minutes. Wash contaminated<br />
skin with soap and water. If ingested, call physician or the Poison Control Centre immediately.<br />
Warranty Disclaimer<br />
<strong>Cloverdale</strong> <strong>Paint</strong> manufactures quality products. In the event that this product is defective or in any way<br />
unsuitable for the application for which it is sold, <strong>Cloverdale</strong> <strong>Paint</strong> Inc. will replace the product free of<br />
charge. The warranty provided by this data sheet is the only warranty or guarantee of quality made in<br />
respect of this product by <strong>Cloverdale</strong> <strong>Paint</strong> Inc. By purchasing this product the customer accepts this<br />
warranty in lieu of all others, and waives all claims to any other remedy arising from any warranty or<br />
guarantee of quality, whether such warranty or guarantee of quality was made expressly to the customer or<br />
implied by any applicable law.<br />
Special Note<br />
This product contains a sufficient level of an Environment Canada approved mildewcide to prevent mould, mildew and<br />
algae from growing on the surface of the coating. As mildew growth is, to a large degree dependent on a surface<br />
preparation and local conditions, <strong>Cloverdale</strong> <strong>Paint</strong> cannot guarantee that mildew will not grow through or on any<br />
contaminants which may have deposited on the surface of the coating.<br />
6950 King George Hwy., Surrey, BC, V3W 4Z1<br />
Web Site: www.cloverdalepaint.com Email: helpdesk@cloverdalepaint.com<br />
Phone: (604) 596-6261 Fax: (604) 597-2677<br />
40-0050v3 2/9/09<br />
<strong>16803</strong> Page 2 of 2<br />
40-0050