Footrest - Torq Distribution

offset
highway pegs
U.S. Patent D405,393 & D411,440
These highway pegs utilize our unique
offset mount to allow riders a range of
adjustment not possible with other clamp-on
style highway pegs. The offset can be rotated 360˚ in a 4" diameter circle to
accommodate tall, short, or average height riders. These can be installed
on any round tubing (frames or engine guards), but it is important to keep in
mind that the footpeg itself will end up perpendicular to the bar to which it is
mounted. If your engine guard is angled in such a way that the peg will not be
level once installed, look to our Right Angle Mounts - pg 137 or Male Adapters
with Adjustable Stop - pg 139.
Small ISO ® -Pegs:
7998 with 1-1/4” Diameter Clamps (pr) $
124.99
Large ISO ® -Pegs:
7999 with 1-1/4” Diameter Clamps (pr) $
135.99
7933 with 1.35” Diameter Clamps (pr)
$
124.99
Note: Work great on Kawasaki front frame tubes.
Dually ISO ® -Pegs: U.S. Patent D405,393
7976 with 1” Diameter Clamps (pr) $
145.99
7966 with 1-1/8” Diameter Clamps (pr) $
145.99
7993 with 1-1/4” Diameter Clamps (pr) $
145.99
7920 with 1.35” Diameter Clamps (pr)
Note: Work great on Kawasaki front frame tubes.
Pilot TM Pegs:
4438 with 1” Diameter Clamps (pr) $
145.99
4436 with 1-1/4” Diameter Clamps (pr) $
145.99
7933
$
139.99
Great Highway Peg
Option for Vulcan
1500/1600!
2"
Many Options
for Ultimate
Adjustability!
3"
360˚
Adjustability!
7993
7999
4438
7998
helpful quick clamp size
selection information
• Baron Standard Engine Guards 1-1/4”
• Cobra Standard Engine Guards 1-1/4”
• Cobra Fatty Engine Guards 1-1/2”
• Kawasaki & Honda VT1300 Custom Line
Front Frame Down Tubes 1.35”
• Valkyrie Curved Part of Engine Guard 1-1/8”
• Yamaha Front Frame Down Tubes,
All Road Star, V Star, Roadliner,
Stratoliner & Raider 1-1/4”
• Yamaha Full Size/Full Loop Engine Guards 1-1/4”
• Honda Full Size/Full Loop Engine Guards 1-1/4”
• Victory Front Frame Down Tubes on ’06
& Up Hammer, Kingpin, Jackpot, & 8Ball 1-1/2”
Note: To measure your tube size either use the tool on page
138 or tighten an adjustable wrench around the tube. Remove
the wrench & measure the opening. Mounting Cruise Pegs off
frame tubes requires 1-1/2" of strait open tube for clamping at
equal height on both sides & approximately 3/8" of clearance
around tube. Many mid 1990's smaller metric engine guards
were a 1" tube.
longhorn offset peg mount
This stylish peg mount provides 360˚ adjustability so it can be used to position the peg closer to the rider or
further away. Its 3-1/4” arm gives an incredible 6-1/2” range of adjustment. Incorporating an innovative locking
device, this mount is guaranteed not to slip.
8016 Longhorn Offset Peg Mounts (pr)
$
72.99
For use with Magnum Quick Clamps only - pg 138.
7985 Longhorn Offset with 1” Clamp (pr)
$
114.99
U.S. Patent D411,440
7986 Longhorn Offset with 1-1/4” Clamp (pr)
U.S. Patent D411,440
$
114.99
8016
4577 Longhorn Offset with 1-1/2” Clamp (pr)
$
117.99
U.S. Patent D411,440
4568 Replacement Peg Mount Clevis (ea) $
21.99
Note: Male Mount Pegs sold separately - pg 142.
Accepts
All Male
Mount Pegs
pg 142
7986
2-1/2"
3-1/4"
F O O T R E S T S
N E W f o r 2 0 1 0 . . .
tour-tech cruise peg mounts
Offering an incredible range of adjustability
for your for Metric Cruisers! See Pg 16
P/N 4520-29
W W W . K U R Y A K Y N . C O M
135