caution - Toro

More documents

Recommendations

Info

Front Deck Lift Cylinder 10 9 RIGHT 7 7 8 9 11 12 FRONT 6 13 5 4 1 2 3 1. Lift cylinder (2 used) 2. Lift arm (LH shown) 3. Lock nut 4. Pin 5. Flange head screw Figure 90 6. Grease fitting 7. O -ring 8. 90 o hydraulic fitting 9. O -ring 10. Hydraulic fitting 11. Pivot pin 12. Cotter pin 13. Grease fitting Hydraulic System Page 4 - 128 Groundsmaster 4100--D
Removal (Fig. 90) 1. Park machine on a level surface, lower cutting deck, stop engine, engage parking brake and remove key from the ignition switch. 2. Read the General Pre<strong>caution</strong>s for Removing and Installing Hydraulic System Components at the beginning of this section. 3. To prevent contamination of hydraulic system during lift cylinder removal, thoroughly clean exterior of cylinder and fittings. NOTE: To ease installation, label the hydraulic hoses to show their correct position on the lift cylinder. 4. Disconnect hydraulic hoses from lift cylinder. 5. Remove flange head screw and lock nut that secure the pin to the lift arm. Remove pin from lift arm and cylinder shaft clevis which will free lift cylinder from lift arm. 6. Remove one cotter pin from upper lift pin. Pull upper lift pin from frame and cylinder barrel clevis. 7. Remove lift cylinder from machine. 8. If hydraulic fittings are to be removed from lift cylinder, mark fitting orientation to allow correct assembly. Remove fittings from cylinder and discard O--rings. Installation (Fig. 90) 1. If fittings were removed from lift cylinder, lubricate and place new O--rings onto fittings. Install fittings into port openings using marks made during the removal process to properly orientate fittings. Tighten fittings (see Hydraulic Fitting Installation in the General Information section of this chapter). 2. Position cylinder barrel clevis to frame and insert upper lift pin into frame and clevis. Secure lift pin with cotter pin. 3. Insert pin through lift arm and cylinder shaft clevis. Secure pin to lift arm with flange head screw and lock nut. 4. Attach hydraulic hoses to lift cylinder. 5. Fill reservoir with hydraulic fluid as required. 6. After assembly is completed, operate lift cylinder to verify that hydraulic hoses and fittings are not contacted by anything. Hydraulic System Groundsmaster 4100--D Page 4 - 129 Hydraulic System
Page 1 and 2:
Part No. 08162SL (Rev. A) Service M
Page 3 and 4:
Table Of Contents Chapter 1 - Safet
Page 5 and 6:
Table of Contents GENERAL SAFETY IN
Page 7 and 8:
Maintenance and Service 1. Before s
Page 9 and 10:
Safety and Instruction Decals Numer
Page 11 and 12:
Chapter 2 Table of Contents Product
Page 13 and 14:
Torque Specifications Recommended f
Page 15 and 16:
Standard Torque for Dry, Zinc Plate
Page 17 and 18:
Chapter 3 Kubota Diesel Engine Tabl
Page 19 and 20:
Specifications Item Make / Designat
Page 21 and 22:
Removal (Fig. 1) 1. Park machine on
Page 23 and 24:
Removal (Fig. 5) CAUTION B The muff
Page 25 and 26:
DANGER Because diesel fuel is highl
Page 27 and 28:
Page 29 and 30:
Engine Removal (Fig. 9) 1. Park mac
Page 31 and 32:
3. Slowly lower engine into the mac
Page 33 and 34:
Coupler Removal (Fig. 16) NOTE: The
Page 35 and 36:
Chapter 4 Hydraulic System Table of
Page 37 and 38:
General Information Operator’s Ma
Page 39 and 40:
Hydraulic Hose and Tube Installatio
Page 41 and 42:
Adjustable Fitting (Fig. 8) 1. Make
Page 43 and 44:
Hydraulic System This page is inten
Page 45 and 46:
Traction Circuit: 4WD (Mow) The tra
Page 47 and 48:
Traction Circuit: Transport (2WD) T
Page 49 and 50:
Lower Cutting Deck A four section g
Page 51 and 52:
Raise Cutting Deck A four section g
Page 53 and 54:
Mow Circuit Hydraulic flow for the
Page 55 and 56:
Page 57 and 58:
Steering Circuit A four section gea
Page 59 and 60:
Engine Cooling Fan Circuit A four s
Page 61 and 62:
Hydraulic Test Fitting Kit This kit
Page 63 and 64:
Problem Traction power is lost or u
Page 65 and 66:
Testing The most effective method f
Page 67 and 68:
Procedure for Traction Circuit Char
Page 69 and 70:
Procedure for Traction Circuit Reli
Page 71 and 72:
Procedure for Counterbalance Pressu
Page 73 and 74:
Procedure for Rear Traction Circuit
Page 75 and 76:
Procedure for Traction Circuit Redu
Page 77 and 78:
Procedure for Cutting Deck Circuit
Page 79 and 80:
Procedure for Cutting Deck Manifold
Page 81 and 82:
Procedure for Cutting Deck Gear Pum
Page 83 and 84:
Procedure for Cutting Deck Motor Ca
Page 85 and 86:
Procedure for Steering Circuit Reli
Page 87 and 88:
Procedure for Lift/Lower Circuit Re
Page 89 and 90:
Procedure for Steering and Lift/Low
Page 91 and 92:
Procedure for Engine Cooling Fan Ci
Page 93 and 94:
Procedure for Engine Cooling Fan Ci
Page 95 and 96:
Service and Repairs General Precaut
Page 97 and 98:
Charge Hydraulic System NOTE: When
Page 99 and 100:
NOTE: The front frame needs to be l
Page 101 and 102:
Removal (Fig. 48) CAUTION The radia
Page 103 and 104:
Removal (Fig 49) 1. Park machine on
Page 105 and 106:
IMPORTANT: Use caution when clampin
Page 107 and 108:
Page 109 and 110:
Removal (Fig. 53) 1. Park machine o
Page 111 and 112: Hydraulic System This page is inten
Page 113 and 114: Removal (Fig. 56) 1. Park machine o
Page 119 and 120: Removal (Fig. 59) NOTE: The ports o
Page 121 and 122: 4WD Manifold Service (Fig. 60) 1. M
Page 123 and 124: Removal (Fig. 61) 1. Read the Gener
Page 125 and 126: Filter Manifold Service (Fig. 62) F
Page 131 and 132: CAUTION The centering springs are u
Page 135 and 136: Disassembly (Fig. 68) 1. Pump oil o
Page 139 and 140: 8. Remove and discard back--up gask
Page 145 and 146: Fan Drive Manifold Service (Fig. 76
Page 147 and 148: Cutting Deck Motor Removal 1. Park
Page 149 and 150: IMPORTANT: Mark the relative positi
Page 153 and 154: Removal (Fig. 85) NOTE: The ports o
Page 155 and 156: PTO Manifold Service (Fig. 86) For
Page 161: Disassembly (Fig. 89) 1. Plug all p
Page 167 and 168: Disassembly (Figs. 92 and 93) 1. Re
Page 171 and 172: Chapter 5 Electrical System Table o
Page 173 and 174: Special Tools Order special tools f
Page 175 and 176: Troubleshooting CAUTION Remove all
Page 177 and 178: Cutting Deck Operating Problems The
Page 179 and 180: Adjustments Wing Deck Position Swit
Page 181 and 182: Component Testing For accurate resi
Page 183 and 184: Warning Lights Engine Oil Pressure
Page 185 and 186: Transport / 4WD Switch The transpor
Page 187 and 188: Seat Switch The seat switch is norm
Page 189 and 190: Hour Meter The hour meter is locate
Page 191 and 192: Start, Engine Shutdown, Seat, Alarm
Page 193 and 194: TEC -5002 Controller Groundsmaster
Page 195 and 196: Fuel Gauge The fuel gauge can be te
Page 197 and 198: Glow Controller The glow controller
Page 199 and 200: Dual Temperature Switch The dual te
Page 201 and 202: Traction Neutral Switch The tractio
Page 203 and 204: Fusible Links The Groundsmaster 410
Page 205 and 206: Cutting Deck Raise and Lower Switch
Page 207 and 208: Service and Repairs NOTE: For engin
Page 209 and 210: 2. Conduct a hydrometer test of the
Page 211 and 212: Chapter 6 Axles, Planetaries and Br
Page 213 and 214:
General Information Operator’s Ma
Page 215 and 216:
3. Chock rear wheels and jack up fr
Page 217 and 218:
This page is intentionally blank. A
Page 219 and 220:
Page 221 and 222:
NOTE: The planetary wheel drive ass
Page 223 and 224:
This page is intentionally blank. A
Page 225 and 226:
8. Remove cap screw and flange nut
Page 227 and 228:
Bevel Gear Case and Axle Case The f
Page 229 and 230:
Bevel Gear Case and Axle Case Insta
Page 231 and 232:
9. Remove the bevel gear case/axle
Page 233 and 234:
Axle Shafts The following procedure
Page 235 and 236:
7. Secure the lock nut with the sta
Page 237 and 238:
Differential Gear Inspection 1. Mea
Page 239 and 240:
Pinion Gear to Ring Gear Engagement
Page 241 and 242:
Chapter 7 Chassis Table of Contents
Page 243 and 244:
Disassembly (Fig. 1) 1. Park machin
Page 245 and 246:
CAUTION When changing attachments,
Page 247 and 248:
Page 249 and 250:
Disassembly (Fig. 8) 1. Disassemble
Page 251 and 252:
NOTE: Most of the seat suspension c
Page 253 and 254:
Removal 1. Park machine on a level
Page 255 and 256:
Chapter 8 Cutting Deck Table of Con
Page 257 and 258:
General Information CAUTION Never i
Page 259 and 260:
This page is intentionally blank. C
Page 261 and 262:
Removal (Fig. 1) 1. Position machin
Page 263 and 264:
Page 265 and 266:
Removal (Fig. 6) 1. Position machin
Page 267 and 268:
Cutting Deck Link Service Disassemb
Page 269 and 270:
Page 271 and 272:
Installation (Fig. 13) 1. Position
Page 273 and 274:
2. Install outer bearing spacer int
Page 275 and 276:
Removal (Fig. 20) 1. Park machine o
Page 277 and 278:
Disassembly (Fig. 22) 1. Park machi
Page 279 and 280:
Chapter 9 Foldout Drawings Table of
Page 281 and 282:
CENTER DECK MANIFOLD COUNTERBALANCE
Page 283 and 284:
CONTINUES FROM SHEET 1 CONTINUES FR
Page 285 and 286:
CONTINUES TO SHEET 2 CONTINUES TO S
Page 287 and 288:
CONTINUES TO SHEET 2 WHEN THE PTO S
Page 289 and 290:
CONTINUES TO SHEET 2 CONTINUES TO S
Page 291 and 292:
YELLOW GRAY YELLOW/BLACK VIOLET WHI
Page 293 and 294:
FLOW DIVIDER SOLENOID Groundsmaster
Page 295 and 296:
(STARTER) (STARTER) (STARTER) Groun
Page 297 and 298:
BLUE GRAY VIOLET BLACK YELLOW GRAY
show all

caution - Toro

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?