Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
SAE Straight Thread O -Ring Port - Non -adjustable<br />
1. Make sure both threads and sealing surfaces are<br />
free of burrs, nicks, scratches, or any foreign material.<br />
2. Always replace the O--ring seal when this type of fitting<br />
shows signs of leakage.<br />
3. Lubricate the O--ring with a light coating of oil.<br />
O-Ring<br />
4. Install the fitting into the port and tighten it down full<br />
length until finger tight.<br />
5. Tighten the fitting to the correct Flats From Finger<br />
Tight (F.F.F.T.).<br />
Size<br />
F.F.F.T.<br />
4 (1/4 in. nominal hose or tubing) 1.00 + 0.25<br />
6(3/8in.) 1.50+0.25<br />
8(1/2in.) 1.50+0.25<br />
10 (5/8 in.) 1.50 + 0.25<br />
12 (3/4 in.) 1.50 + 0.25<br />
16 (1 in.) 1.50 + 0.25<br />
NOTE: Installation torque values for non--adjustable fittings<br />
are listed in Figure 4. These torque values should<br />
only be used when a fitting can be accessed with a<br />
socket. Use of an offset wrench (e.g. crowfoot wrench)<br />
will affect torque wrench accuracy and should not be<br />
used.<br />
SAE Straight Thread O -Ring Port - Adjustable<br />
1. Make sure both threads and sealing surfaces are<br />
free of burrs, nicks, scratches, or any foreign material.<br />
2. Always replace the O--ring seal when this type of fitting<br />
shows signs of leakage.<br />
3. Lubricate the O--ring with a light coating of oil.<br />
Figure 3<br />
Fitting Size Installation Torque<br />
4 9--10ft--lb(12--13N--m)<br />
6 20 -- 21 ft -- lb (27 -- 28 N -- m)<br />
8 35 -- 37 ft -- lb (47 -- 50 N -- m)<br />
10 60 -- 66 ft -- lb (81 -- 89 N -- m)<br />
12 81 -- 87 ft -- lb (110 -- 117 N -- m)<br />
16 121--131 ft--lb (164--177 N--m)<br />
Figure 4<br />
Lock Nut<br />
Hydraulic<br />
System<br />
4. Turn back the jam nut as far as possible. Make sure<br />
the back up washer is not loose and is pushed up as far<br />
as possible (Step 1).<br />
5. Install the fitting into the port and tighten finger tight<br />
until the washer contacts the face of the port (Step 2).<br />
Figure 5<br />
O-Ring<br />
Back -up Washer<br />
6. To put the fitting in the desired position, unscrew it by<br />
the required amount, but no more than one full turn<br />
(Step 3).<br />
Step 1<br />
Step 3<br />
7. Hold the fitting in the desired position with a wrench<br />
and turn the jam nut with another wrench to the correct<br />
Flats From Finger Tight (F.F.F.T.) (Step 4).<br />
Size<br />
F.F.F.T.<br />
4 (1/4 in. nominal hose or tubing) 1.00 + 0.25<br />
6(3/8in.) 1.50+0.25<br />
8(1/2in.) 1.50+0.25<br />
10 (5/8 in.) 1.50 + 0.25<br />
12 (3/4 in.) 1.50 + 0.25<br />
16 (1 in.) 1.50 + 0.25<br />
Step 2 Step 4<br />
Figure 6<br />
<strong>Multi</strong> <strong>Pro</strong> <strong>5700</strong>--D<br />
Page 4 - 5<br />
Hydraulic System