Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
6. Disconnect throttle cable from engine (Fig. 8).<br />
A. Loosen jam nut that secures throttle cable to<br />
throttle plate on engine.<br />
B. Remove e–ring that secures throttle cable to<br />
speed control lever on engine.<br />
C. Position throttle cable away from the engine.<br />
7. Remove fasteners that secure spray control console<br />
to seat box assembly (Fig. 9). Carefully pivot seats and<br />
control console forward to allow radiator access. Take<br />
care not to damage the wire harness or throttle cable.<br />
8. Remove four (4) cap screws (item 19), lock washers<br />
and flat washers that secure fan shroud to radiator.<br />
9. Remove two (2) cap screws (item 22), flat washers<br />
and flange nuts that attach fan shrouds.<br />
10.Carefully lift upper fan shroud from machine.<br />
11. Remove two (2) flange nuts (item 26) that secure the<br />
isomounts on the bottom of the radiator to the machine<br />
frame.<br />
12.Carefully lift radiator up from machine.<br />
Installation (Figs. 7)<br />
1. Replace any foam seal pieces that are damaged or<br />
deteriorated.<br />
2. Make sure that lower fan shroud is positioned below<br />
fan.<br />
3. Carefully lower radiator to the machine frame. Secure<br />
isomounts on the bottom of the radiator to the machine<br />
frame with two (2) flange nuts.<br />
4. Position upper fan shroud to radiator. Attach fan<br />
shrouds with cap screws (item 22), flat washers and<br />
flange nuts.<br />
5. Secure radiator shrouds to radiator with four (4) cap<br />
screws (item 19), lock washers and flat washers. Make<br />
sure that clearance exists between radiator shrouds<br />
and fan at all points before tightening fasteners.<br />
6. Connect lower and upper hoses to the radiator. Secure<br />
hoses with hose clamps.<br />
7. Carefully pivot seats and spray control console back<br />
in position taking care not to damage wiring harness or<br />
throttle cable. Install fasteners to secure control console<br />
to seat box assembly.<br />
8. Reconnect throttle cable to engine (Fig. 8).<br />
A. Position throttle cable end to speed control lever<br />
on engine and secure with e–ring.<br />
B. Secure throttle cable to throttle plate on engine<br />
with jam nut.<br />
9. Secure radiator shroud to radiator with six (6) cap<br />
screws (items 5 and 6), lock washers and flat washers.<br />
10.Place overflow hose to radiator flange and secure<br />
with hose clamp (Fig. 9).<br />
11. Make sure radiator drain is closed. Fill radiator with<br />
coolant (see Operator’s Manual).<br />
12.Check position of wires, hydraulic hoses and control<br />
cables for proper clearance with rotating, high temperature<br />
and moving components.<br />
13.Start engine and check for proper operation. Check<br />
all hose connections for leaks.<br />
1<br />
2<br />
Figure 8<br />
1. Throttle cable 2. Throttle plate<br />
2<br />
Figure 9<br />
1. Overflow hose 2. Spray console fastener<br />
1<br />
2<br />
Kubota Diesel<br />
Engine<br />
<strong>Multi</strong> <strong>Pro</strong> <strong>5700</strong>–D Page 3 – 11 Kubota Diesel Engine