Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Spray Control Assembly<br />
SERIAL NUMBER BELOW 250999999 SHOWN<br />
10<br />
20<br />
15<br />
14<br />
13<br />
6<br />
5<br />
12<br />
9<br />
9<br />
11<br />
4<br />
19<br />
18<br />
17<br />
16<br />
5<br />
7<br />
6<br />
9<br />
10<br />
21<br />
22<br />
23<br />
24<br />
25<br />
28<br />
20<br />
27<br />
26<br />
29<br />
30<br />
3<br />
2<br />
35<br />
18<br />
29<br />
22<br />
4<br />
3<br />
5<br />
1<br />
34<br />
33<br />
32<br />
31<br />
5<br />
8<br />
9<br />
FRONT<br />
RIGHT<br />
1. Boom valve motor assembly<br />
2. O -ring<br />
3. Flange nut<br />
4. Flange nut<br />
5. Flange head screw<br />
6. Boom mounting bracket<br />
7. Cross support angle<br />
8. RH boom mount<br />
9. Flange nut<br />
10. Boom hold -in assembly<br />
11. Valve mounting bar<br />
12. LH boom mount<br />
Figure 20<br />
13. Flange head screw<br />
14. R -clamp<br />
15. Support bracket<br />
16. Tee assembly<br />
17. Agitation valve motor<br />
18. O -ring<br />
19. Hosebarb<br />
20. Hose clamp<br />
21. Agitation supply hose (1”)<br />
22. Fork<br />
23. Flange head screw<br />
24. Flange head screw<br />
25. Carriage bolt<br />
26. Mount bracket<br />
27. Boom bypass hose (1”)<br />
28. Fork<br />
29. Hose clamp<br />
30. Boom supply hose (3 used)<br />
31. Boom supply hose (1 1/2”)<br />
32. Hose clamp<br />
33. Hosebarb<br />
34. Pressure gauge tube<br />
35. Hosebarb<br />
IMPORTANT: Make sure to remove and neutralize<br />
chemicals from spray components before disassembly.<br />
Wear protective clothing, chemical resistant<br />
gloves, and eye protection during repair.<br />
Removal (Fig. 20)<br />
1. Park machine on a level surface, stop engine, engage<br />
parking brake, and remove key from the ignition<br />
switch.<br />
2. On machines with serial number below 310000000,<br />
remove two (2) flange head screws and flange nuts that<br />
secure support bracket (item 15) to mount bracket (item<br />
26). Position bracket away from spray control assembly.<br />
3. Label hoses for proper installation after repairs are<br />
completed (Fig. 21). Loosen hose clamps and disconnect<br />
hoses from spray control assembly as needed.<br />
Spray System<br />
Page 6 - 20<br />
Rev. D<br />
<strong>Multi</strong> <strong>Pro</strong> <strong>5700</strong>--D
Change language