Multi Pro 5700 - Toro

More documents

Recommendations

Info

Agitation Nozzles (Tank Mounted) 1 2 21 4 3 10 5 9 1 8 7 6 2 10 9 6 2 10 9 8 1 7 11 12 2 3 4 1 8 1 3 1 4 6 7 19 5 12 5 13 1 5 14 5 13 1 15 5 16 FRONT 20 5 RIGHT NOTE: ARROWS SHOW FLUID FLOW DIRECTION 18 17 15 1. O–ring 2. Fork 3. Hosebarb 4. Bulkhead nut 5. Hose clamp 6. Bulkhead gasket 7. Bulkhead fitting Figure 14 8. Elbow fitting 9. Agitation nozzle 10. Nut 11. Hose (3/4”) 12. Nut 13. Hosebarb 14. Hose (3/4”) 15. Tee fitting 16. Hose (3/4”) 17. R clamp 18. Flange head screw 19. Hose (3/4”) 20. Agitation supply hose (3/4”) 21. Spray tank Spray System Page 6 – 16 Multi Pro 5700–D
IMPORTANT: Make sure to remove and neutralize chemicals from tank and other components before disassembly. Wear protective clothing, chemical resistant gloves, and eye protection during repair. Disassembly (Fig. 14) 1. Park machine on a level surface, stop engine, engage parking brake, and remove key from the ignition switch. 2. Drain spray tank (see Operator’s Manual). 3. Label disconnected hoses for proper installation after repairs are completed. 1 SERIAL NUMBER BELOW 310000000 2 4. Remove agitation nozzles as required using Figure 14 as a guide. Discard all removed O--rings and gaskets. Figure 15 1. Agitation valve motor 2. Agitation supply hose Assembly (Fig. 14) NOTE: Coat all O--rings with vegetable oil before installation to reduce the chance of damage during assembly. 1. Install agitation nozzles using Figure 14 as a guide. Replace all removed O--rings and gaskets. 1 SERIAL NUMBER ABOVE 310000000 2. Check spray system for leaks. 2 Figure 16 1. Agitation valve motor 2. Agitation supply Spray System Rev. D Multi Pro 5700--D Page 6 - 17 Spray System
Page 1 and 2:
PART NO. 04130SL (Rev. D) Service M
Page 3 and 4:
Table Of Contents Chapter 1 - Safet
Page 5 and 6:
Table Of Contents (Continued) Chapt
Page 7 and 8:
Chapter 1 Safety Safety Table of Co
Page 9 and 10:
Maintenance and Service 1. Before s
Page 11 and 12:
Chapter 2 Product Records and Maint
Page 13 and 14:
Torque Specifications Recommended f
Page 15 and 16:
Standard Torque for Dry, Zinc Plate
Page 17 and 18:
Maintenance Maintenance procedures
Page 19 and 20:
Chapter 3 Kubota Diesel Engine Tabl
Page 21 and 22:
Kubota Diesel Engine This page is i
Page 23 and 24:
DANGER Because diesel fuel is highl
Page 25 and 26:
Removal (Fig. 4) NOTE: For air clea
Page 27 and 28:
Installation (Fig. 6 or 7) 1. Insta
Page 29 and 30:
6. Disconnect throttle cable from e
Page 31 and 32:
CAUTION Exhaust system components m
Page 33 and 34:
15.Check engine oil level and adjus
Page 35 and 36:
Chapter 4 Hydraulic System Table of
Page 37 and 38:
Specifications Item Piston (Tractio
Page 39 and 40:
SAE Straight Thread O -Ring Port -
Page 41 and 42:
This page is intentionally blank. H
Page 43 and 44:
Hydraulic Flow Circuits Traction Ci
Page 45 and 46:
Spray Pump Drive Circuit A single s
Page 47 and 48:
O -Ring Kit Toro Part Number: 16 -3
Page 49 and 50:
Machine travels too far before stop
Page 51 and 52:
Traction Circuit Charge Pressure Te
Page 53 and 54:
Gear Pump Flow Test Output from the
Page 55 and 56:
Steering Control Valve and Steering
Page 57 and 58:
Wheel Motor Efficiency: Case Drain
Page 59 and 60:
Adjustments Adjust Traction Pedal f
Page 61 and 62:
Service and Repairs General Precaut
Page 63 and 64:
Charge Hydraulic System NOTE: When
Page 65 and 66:
Removal (Fig. 26) 1. Park machine o
Page 67 and 68:
Hydraulic System This page is inten
Page 69 and 70:
3. Operate all hydraulic controls t
Page 71 and 72:
Manual Servo Control Assembly 44 to
Page 73 and 74:
Page 75 and 76:
Hydraulic System This page is inten
Page 77 and 78:
Page 79 and 80:
Relief Valve Removal 1. Park machin
Page 81 and 82:
Page 83 and 84:
Removal (Fig. 45) 1. Park the machi
Page 85 and 86:
CAUTION The centering springs are u
Page 87 and 88:
Page 89 and 90:
Disassembly (Fig. 52) 1. Remove oil
Page 91 and 92:
Page 93 and 94: Removal (Fig. 54) 1. Park the machi
Page 95 and 96: Chapter 5 Electrical System Table o
Page 97 and 98: Special Tools Order these special t
Page 99 and 100: Starting Problems (continued) Probl
Page 101 and 102: Component Testing For accurate resi
Page 103 and 104: Headlight Switch The headlight swit
Page 105 and 106: Brake Pedal Switch The brake pedal
Page 107 and 108: Indicator Lights High Temperature W
Page 109 and 110: Accessory Solenoid The accessory so
Page 111 and 112: Spray Pump, Agitation and Boom Cont
Page 113 and 114: Pulse Width Modulated (PWM) Valve S
Page 115 and 116: Relays The Multi Pro 5700-D uses th
Page 117 and 118: Fuel Stop Solenoid The fuel stop so
Page 119 and 120: Fuel Pump The fuel pump is attached
Page 121 and 122: Service and Repairs NOTE: See the K
Page 123 and 124: Cruise Control Coil Removal (Fig. 4
Page 125 and 126: Battery Service The battery is the
Page 127 and 128: H. Using the table below, determine
Page 129 and 130: Chapter 6 Spray System Table of Con
Page 131 and 132: General Information Precautions Con
Page 133 and 134: Spray System Operation The Multi Pr
Page 135 and 136: Erratic spray operation from booms.
Page 137 and 138: Pressure Dampener The pressure damp
Page 139 and 140: 5. Remove lock nuts, flat washers,
Page 141 and 142: Disassembly (Fig. 9) IMPORTANT: Mak
Page 143: This page is intentionally blank. S
Page 147 and 148: IMPORTANT: Make sure to remove and
Page 149 and 150: 4. If boom valve motor assembly is
Page 151 and 152: IMPORTANT: Boom valve motors may ha
Page 153 and 154: IMPORTANT: The agitation valve moto
Page 155 and 156: 4. Remove rear housing cover from v
Page 157 and 158: Boom and Agitation Valve Motor Serv
Page 159 and 160: Disassembly (Fig. 30) IMPORTANT: Ma
Page 161 and 162: NOTE: If suction tube in tank devel
Page 163 and 164: Disassembly (Fig. 33) IMPORTANT: Ma
Page 165 and 166: Disassembly (Fig. 37.1) IMPORTANT:
Page 167 and 168: Turret Body Service Disassembly (Fi
Page 169 and 170: Disassembly (Fig. 38) 1. Park machi
Page 171 and 172: Assembly (Fig. 41) 1. If pivot brac
Page 173 and 174: Adjustment 1. Loosen end nut that s
Page 175 and 176: Disassembly (Fig. 47) 1. Remove fou
Page 177 and 178: Removal (Fig. 48) 1. Park machine o
Page 179 and 180: Actuator Oil Level Under normal con
Page 181 and 182: Chapter 7 Chassis Table of Contents
Page 183 and 184: Service and Repairs Tie Rod Ends Re
Page 185 and 186: Removal (Fig. 3) 1. Park machine on
Page 187 and 188: Disassembly (Fig. 4) 1. Park machin
Page 189 and 190: Disassembly (Fig. 5) 1. Park machin
Page 191 and 192: 3. Chock front wheels and jack up r
Page 193 and 194: Brake Cables Removal 1. Remove brak
Page 195 and 196:
Page 197 and 198:
NOTE: The planetary wheel drive ass
Page 199 and 200:
Table of Contents GENERAL INFORMATI
Page 201 and 202:
Special Tools Diagnostic Display Th
Page 203 and 204:
Sonic Boom System This page is inte
Page 205 and 206:
Sprayer Operation on Level Turf Dur
Page 207 and 208:
Downward Slope in Turf Encountered
Page 209 and 210:
Rise in Turf Encountered During spr
Page 211 and 212:
Boom Level Changed by Operator Duri
Page 213 and 214:
Manual Boom Operation During spraye
Page 215 and 216:
Diagnostic Display The Sonic Boom S
Page 217 and 218:
Verify Diagnostic Display Output Fu
Page 219 and 220:
Problem One of the boom actuators w
Page 221 and 222:
Relays The Sonic Boom System uses s
Page 223 and 224:
Sonic Sensor Two (2) identical soni
Page 225 and 226:
Chapter 8 Electrical Diagrams Table
Page 227 and 228:
R/BK IGNITION SWITCH OFF RUN START
Page 229 and 230:
All relays and solenoids are shown
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
PINK PINK GRAY GRAY GRAY GRAY VIOLE
Page 237 and 238:
PINK PINK ORANGE RED RED/BLACK RED
Page 239 and 240:
RED ORANGE GREEN/RED GREEN/RED PINK
Page 241 and 242:
RED RED BROWN BROWN BROWN PINK PINK
Page 243 and 244:
Rev. D Page 8 - 19 Multi Pro 5700--
Page 245 and 246:
WHITE RED GREEN YELLOW GREEN YELLOW
Page 247 and 248:
Rev. D Page 8 - 23 Multi Pro 5700--
show all

Multi Pro 5700 - Toro

Create successful ePaper yourself

Delete template?

Save as template?