Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
Multi Pro 5700 - Toro
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
5. Remove lock nuts, flat washers, cap screws, and<br />
coupler spacers that secure rubber coupling to pump<br />
hub.<br />
6. Remove four (4) flange head screws and flange nuts<br />
that secure pump to pump mount bracket.<br />
7. Remove pump from machine.<br />
8. If needed, loosen set screws in pump hub. Pull hub<br />
from pump shaft. Locate and remove key from pump<br />
shaft. Remove set screws from pump hub. Clean<br />
threads of set screws and hub.<br />
9. Secure pump to mounting bracket by tightening<br />
flange head screws and flange nuts.<br />
10.Position front and rear guard plates to pump mount<br />
bracket. Install and tighten flange head screw and<br />
flange nut to guard plates. Install flange nuts to secure<br />
guard plates to pump mount bracket.<br />
11.Install pressure and suction hoses to correct barb fittings<br />
(Fig. 7). Secure hoses with hose clamps.<br />
9. If needed, remove pressure dampener, tee fitting<br />
(pressure), and elbow fitting (pressure) from pump outlet<br />
(Fig. 8).<br />
10.If needed, remove suction dampener and tee fitting<br />
(suction) from pump inlet (Fig. 8).<br />
Installation (Fig. 6)<br />
NOTE: Coat all spray system O--rings with vegetable<br />
oil before installation to reduce the chance of damage<br />
during assembly.<br />
2<br />
1<br />
1. Apply PTFE tape to threads of removed tee fitting<br />
(pressure), elbow fitting (pressure), and tee fitting (suction).<br />
Position new O--rings and gaskets on suction and<br />
pressure fittings that were removed during disassembly.<br />
2. If removed, install tee fitting (suction) and suction<br />
dampener to pump inlet. Orientate tee toward rear of<br />
machine (Fig. 8).<br />
1. Pressure hose 2. Suction hose<br />
10<br />
8<br />
9<br />
Figure 7<br />
6<br />
7<br />
6<br />
3. If removed, install elbow fitting (pressure), tee fitting<br />
(pressure), and pressure dampener to pump outlet.<br />
Orientate elbow toward rear of machine (Fig. 8).<br />
4. If pump hub was removed, apply antiseize lubricant<br />
to pump shaft. Install key in shaft and slide pump hub<br />
onto shaft.<br />
11<br />
12<br />
13<br />
14<br />
15<br />
5<br />
4<br />
3<br />
2<br />
1<br />
Spray<br />
System<br />
5. Position pump on pump mounting bracket and install<br />
flange head screws and flange nuts to pump and mounting<br />
bracket. Leave fasteners loose.<br />
17<br />
16<br />
9<br />
6. Place coupling spacers into rubber coupling. Install<br />
cap screws, flat washers, and lock nuts to secure rubber<br />
coupling to pump hub. Make sure that cap screw<br />
threads extend through lock nut.<br />
7. If pump hub was removed, apply Loctite #242 (or<br />
equivalent) to threads of pump hub set screws. Install<br />
set screws into pump hub to secure hub to pump shaft.<br />
8. Turn pump shaft by hand and position pump on<br />
mounting bracket to best align the coupling assembly<br />
between the pump shaft and the hydraulic motor shaft.<br />
1. Spray pump<br />
2. Pressure hose (1”)<br />
3. Hose clamp<br />
4. Hose barb<br />
5. Nut<br />
6. Gasket<br />
7. Tee fitting (pressure)<br />
8. Elbow fitting (pressure)<br />
9. O -ring<br />
Figure 8<br />
10. Pressure dampener<br />
11. Suction hose (1 1/2”)<br />
12. Hose clamp<br />
13. Nut<br />
14. Seal<br />
15. Tee fitting (suction)<br />
16. Suction dampener<br />
17. Hose barb<br />
<strong>Multi</strong> <strong>Pro</strong> <strong>5700</strong>--D Page 6 - 11 Rev. D<br />
Spray System