Please note - Swinburne University of Technology

NM024 Turning 4
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical.
Content
Multi start screw cutting V-threads and square threads.
NM025 Turning l
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical.
Content
Basic parallel turning to toleranced drawings.
NM026 Turning 2
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering (Basic) and
(Mechanical) and the Swinburne Certificate in Engineering
Practice.
Content
Advanced turning of tapers, ~arallel form turning, face
plate work and use of steadies.
NM027 Turning 3
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical.
Content
Single start screw cutting V-threads metric and imperial.
NM028 Fitting Techniques 2
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical.
Content
V-belts - couplings, balance of pulleys, pipe bending,
fitting of pipe work, mechanical and static seals.
NM020 Mechanical Power Transmission
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Engineering Post Trade course.
g Content
S Belts, chain drives, gears and reduction systems, mechanical
3 power transmission, clutches, bearings, types of
?f transmission.
-
M
NM030 Fluid Power
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical.
Content
Basic hydraulic and pneumatic systems.
NM031 Pneumatics l
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical.
Content
Compressed air generation and distribution, pneumatic
components, pneumatic circuitry, servicing.
NM032 Hydraulics l
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificate in Engineering - Mechanical, and
the Engineering Post Trade course.
Content
Basic hydraulics. Basic hydraulic component specifications,
graphic symbols, fault finding in hydraulic circuits.
NM033 Fluid Power Control 1
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Engineering Post Trade course.
Content
Safety in auto fluid power systems, fluid power control
systems, control switching, relay logic, electro- hydraulic/
pneumatic controls, electrical equipment.
NM034 Air Compression Distribution
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Engineering Post Trade course.
Content
Air compressors, air receivers, compressed air distribution
systems, maintenance procedures of compressors.
NM044 Engineering Drawing Interpretation 2
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificateof Engineering (Mechanical).
Content
Advanced engineering drawing interpretation, formal third
angle projection drawing, sectioning, detail drawing,
assembly drawing.
NM045 Electrical Discharge Machines
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Certificateof Engineering (Mechanical) and
the Engineering Post Trade course.
Content
The process and principles of EDM, preparation of
electrodes. Use of EDM die sink and CNC wire cutting
machines, including the preparation of programs for these
machines.
NM046 Press Tool l Introduction
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Engineering Post Trade course.
Content
Typical pressed components, stainless steel aluminium
copper and brass, zinc allots, punch, die, punch holder,
stripper, guides, stops, pilot, shedder, backing plate,
blanking, piercing, bending, forming, drawing, coining
effect of heat treatment on common features of press-tools,
die set, pillars, bushes, screws, dowels, stripper butts,
locaters etc.
NM047 Press Tool 2 Blank and Pierce
A 40 hour module Hawthorn Prerequisite: nil
A subject in the Engineering Post Trade course.
Content
Blanking and pierce dies, cutting action - design of punch